Table of Contents
Advertisement
About this Manual
1.2 About this Manual
This manual is intended to be a complete reference for all installation and operation tasks for the GWF-7075. Please let us know if the
manual does not meet your needs in any way. We value your feedback!
1.2.1 Terms Used in this Manual
The following terminology is used with the GWF-7075 system. For additional information on the compatible devices, refer to the Com-
patibility Addendum to Gamewell-FCI Manuals, P/N:9000-0427-L8.
Term
SLC
Module
Input Point
Input Zone
Output Point
(or Output Circuit)
Group (or "Output Group")
Output (or "Cadence") Pattern
Mapping
SWIFT
1.3 Compatible Products
The chart below lists the products available from Gamewell-FCI for use with the GWF-7075.
NOTE: For additional information on compatible devices, refer to the Compatibility Addendum to Gamewell-FCI Manuals,
P/N: 9000-0427-L8.
Type of Device
Velociti mode
For a list of compatible devices, refer to Section 5.1 and the Compatibility Addendum of Gamewell-FCI Manuals,
Addressable SLC
P/N:9000-0427-L8.
Devices
SWIFT Wireless
See Section 5.2 for a list of compatible devices
SLC Devices
Other Modules
5824 Serial/Parallel Printer
Interface Module
GFPS-6S NAC Expander
RA-1000 and RA-1000R LCD
Annunciator
5860TG and 5860TR Trim Ring Trim ring kits for surface mounting the RA-1000 annunciator. 5860TG is gray; 5860TR
5880 LED Driver Module
Wireless
VW-GATE
VW-DIS-D
WSD-P
WSD-ACCLIMATE
WTD-RH
WTD-H
WAM-MM
B210W
Miscellaneous
HFSS Honeywell Fire Software
Suite
7860 Telephone Cord
7628
DF-50
CELL-MOD
CELL-CAB-GWF
MRD-1
GWF-7075 Addressable Fire Alarm Control Panel Manual — P/N LS10147-002GF-E:E 06/11/2019
Signaling Line Circuit
The term module is used for all hardware devices except for SLC addressable devices and notification
appliances. This includes the GWF-7075 panel itself.
An addressable sensing device, such as a smoke or heat detector or a contact monitor device.
A protected area made up of input points.
A notification point or circuit for notification appliances. Relay circuits and auxiliary power circuits are
also considered output points.
A group of output points. Operating characteristics are common to all output points in the group.
The pattern that the output will use, for example, Constant, March Code, ANSI 3.41. Applies to zones
and special system events. See Appendix Appendix B:, "Cadence Patterns" for additional information.
Mapping is the process of specifying which outputs are activated when certain events occur in the
system. Section 6.2 explains mapping in detail.
Smart Wireless Integrated Fire Technology
Table 1.2 Manual Terminology
Model
Allows a printer to be attached for the on-site event logging. Maximum of four 5824s
per control panel.
Provides 4 additional Notification Appliance Circuits/Auxiliary power. (Up to 8 per
GWF-7075 system.)
4 x 20 Remote LCD annunciator can be used in any combination, up to a total of 8
devices on one panel.
is red.
Driver for up to 40 LEDs. Interfaces with customized annunciator boards. In addition
the 5880 has eight generic switch input points.
Velociti Wireless SWIFT Gateway
SWIFT Wireless Display Driver
Velociti Wireless Photoelectric Smoke Detector requires 1 B210W base
Velociti Wireless Multi criteria Sensor Intelligent SWIFT Acclimate detector
Velociti Wireless Thermal Detector Rate-of-Rise, 135° Requires one B210W base
Velociti Wireless Thermal Detector, 135° fixed. Requires one B210W base for
installation
Wireless Monitor module
Wireless 6" (15.23cm) flanged Base
For communication and panel programming with a Windows-based computer. Enables
remote viewing of detector status and event history.
RJ31X cord for connecting phone line to the GWF-7075
UL Listed End-of-line resistor.
Dead Front insert.
Cellular board with Plastic Enclosure
Cellular board with Metal Enclosure
Manual Releasing Disconnect Assembly Instructions (P/N:LS10231-000GE-E)
Table 1.3 GWF-7075 Compatible Products
Description
Description
Introduction
9
Advertisement
Table of Contents
