kozy heat BAYPORT 36 LE Installation And Operation Manual

kozy heat BAYPORT 36 LE Installation And Operation Manual

Direct vent gas fireplaces
Table of Contents

Advertisement

Quick Links

HUSSONG MANUFACTURING CO., INC.
B A Y P O R T 3 6 L E
B A Y P O R T 3 6 M V
Models #BAY-36-LE & #BAY-36-MV
Direct Vent Gas Fireplaces
English and French installation manuals are available through your
local dealer. Visit our website www.kozyheat.com.
Les manuels d'installation en français et en anglais sont disponibles
chez votre détaillant local. Visitez www.kozyheat.com .
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
ͷ Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
ͷ WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
ͷ Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
Hussong Mfg. Co., Inc.
BAY-36-LE & BAY-36-MV Report No: 19-507
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATION AND
OPERATION MANUAL
This
appliance
an
aftermarket,
manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
DANGER
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed for the protection
of children and other at-risk individuals.
may
be
installed
permanently
located,
HOT GLASS WILL
CAUSE BURNS
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS
Rev. 11, April 2021
Starting Serial Number: 20 105348 21
in

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BAYPORT 36 LE and is the answer not in the manual?

Questions and answers

Summary of Contents for kozy heat BAYPORT 36 LE

  • Page 1 INSTALLATION AND OPERATION MANUAL HUSSONG MANUFACTURING CO., INC. B A Y P O R T 3 6 L E B A Y P O R T 3 6 M V Models #BAY-36-LE & #BAY-36-MV Direct Vent Gas Fireplaces English and French installation manuals are available through your local dealer.
  • Page 3: Homeowner Reference Information

    Please retain this owner’s manual for future reference. CON GRAT ULAT I ON S! We welcome you as a new owner of a Kozy Heat gas fireplace. Kozy Heat products are designed with superior components and materials, and assembled by trained craftsmen who take pride in their work.
  • Page 5: Table Of Contents

    6.2 Minimum Termination Clearances ............28 14.0 REPLACEMENT PARTS LIST..........66 7.0 VENTING .................. 29 LIMITED LIFETIME WARRANTY ............ 69 7.1 Rear Vent Conversion Instructions............29 #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces TABLE OF CONTENTS 5...
  • Page 7: Introduction

    Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified. #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces INTRODUCTION 7...
  • Page 8: Specifications

    • The AC power supply to this appliance must be hot at all times and shall not have a switch installed in it. 8 SPECIFICATIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 9: Appliance Dimensions

    ” (49mm) (58mm) ⁄ ” ⁄ ⁄ ” ” (829mm) (208mm) GAS LINE HOLE (152mm) ELECTRICAL ACCESS ¾ ” (907mm) Figure 2.1, Appliance Dimensions #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces SPECIFICATIONS 9...
  • Page 10: Safety Barrier Dimensions

    3” (76mm) ABOVE THE HEARTH (941mm) ⁄ AND 3” (76mm) CLEARANCE ” FROM THE OUTSIDE EDGE (819mm) TO A SIDEWALL B36A-FPDSF2 B36-PTF2 Figure 2.2, Safety Barrier Dimensions 10 SPECIFICATIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 11: Framing

    • If the appliance is to be installed above floor level, a solid, continuous platform must be constructed below the appliance. #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 11...
  • Page 12: Stand-Off Assembly And Installation

    FORMED STAND-OFFS AND NAILING FLANGES Framing Studs Stand-o Flange 1/4” (6mm) Clearance FRONT VIEW Stand-o Flange Figure 3.1, Nailing Flange and Stand-off Assembly and Installation 12 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 13: Clearances To Combustibles

    TOP VENT ⁄ ” (301mm) ⁄ ” (905mm) ¼ ” (6mm) ⁄ ” ¼ ” (628mm) (920mm) ⁄ ” (1280mm) Figure 3.2, Typical Installation Options #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 13...
  • Page 14: Wall Enclosure Rough Opening

    ” (920mm) ½ ” (13mm) TYPICAL ⁄ ” FINISH MATERIAL (403mm)* *INCLUDES ½” (13mm) TYPICAL FINISH MATERIAL WITH FLUSH MOUNT Figure 3.3, Framing Dimensions 14 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 15: Vent Termination Framing

    Kozy Heat’s #700-WPT, or wall thimble products that comply with the required 1” (25mm) top clearance to combustibles, must be installed for all horizontal vent runs that pass through interior or exterior walls.
  • Page 16 (1295mm) (991mm) 26” (661mm) 700-WPT Framing Dimensions Ships with #700-2 ½ ” (241mm) ½ ” (241mm) ¾ ” (120mm) Figure 3.4, Minimum Horizontal Venting 16 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 17: Outdoor Covered Fireplace Installation

    The width of the overhang to EACH side of the replace (C) must be 5’ or greater. Figure 3.5, Outdoor Covered Fireplace Install - 1 #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FRAMING 17...
  • Page 18 MINIMUM WEATHERPROOF OVERHANG IN FRONT AND SIDES INSIDE OUTSIDE FREE STANDING STRUCTURE (WEATHERPROOF ENCLOSURE) Figure 3.6, Outdoor Covered Fireplace Install - 2 18 FRAMING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 19: Facing And Finishing

    (top or rear): 45-1/2” (1556mm). • Natural gas and propane minimum chamber height for horizontal vent terminations using flex pipe: 55-1/2” (1410mm). #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 19...
  • Page 20 **NON-COMBUSTIBLE ZONE: 55-1/2” (1410mm) minimum chamber height for top vent minimum horizontal vent terminations using ex pipe Figure 4.2, B36-RSF2 Mantel Requirements 20 FACING AND FINISHING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 21 NOTE: 37-3/4” x 10-1/2” NONCOMBUSTIBLE MATERIAL SUPPLIED WITH FIREPLACE ALLOWS 3/4” OVERLAP ONTO FRAMING SIDES AND 1/2” ONTO HEADER Figure 4.4, BAY-36 Non-Combustible Zone #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 21...
  • Page 22: Finishing Trim Kit Assembly #B36-Ftk

    Use screws included in the components packet to complete side panel installation. If installed, remove the top stand-offs. Figure 4.5, Finishing Trim Kit Installation #B36-FTK 22 FACING AND FINISHING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 23: Exterior Trim Kit Assembly

    Install the exterior trim top panel. Align the holes in the top trim panel with the front holes in the stand-offs and attach to the Figure 4.6, Exterior Trim Kit Installation #B36-081 #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 23...
  • Page 24: Safety Barrier Installations

    BACK OF THE FIREPLACE SAFETY SCREEN FRONT MUST MAKE CONTACT WITH THE FIREPLACE FACE/ FINISH MATERIAL Figure 4.7, B36-RSF2 Install Figure 4.8, Side View Gasket Install 24 FACING AND FINISHING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 25 To remove safety screen: lift the screen up and out of slots. FIRST POSITION NOTCHED TAB LOUVER FIRST POSITION LOUVER NOTCH Figure 4.9, Safety Screen Louver and Notch Locations Figure 4.11, Adjust Louver #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FACING AND FINISHING 25...
  • Page 26: Gas Line Connection

    See Figure 2.1, Appliance Dimensions on page 9. • Do not run gas line in a manner that would obstruct fan operation. 26 GAS LINE CONNECTION Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 27: Termination Locations

    Over 12/12 to 14/12 1.52 Over 14/12 to 16/12 1.83 Over 16/12 to 18/12 2.13 Over 18/12 to 20/12 2.27 Over 20/12 to 21/12 2.44 #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces TERMINATION LOCATIONS 27...
  • Page 28: Minimum Termination Clearances

    Manufacturing Co., Inc. will not be held responsible for heat damage caused from terminating under vinyl overhangs, vinyl ceilings, or vinyl ventilated/ unventilated soffits. 28 TERMINATION LOCATIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 29: Venting

    2. REMOVE (4) SCREWS SECURING 6-5/8” COMBUSTION AIR INTAKE COLLAR 3. REMOVE (6) SCREWS SECURING EXHAUST COVER PLATE 3. REMOVE (6) SCREWS SECURING 4” EXHAUST COLLAR #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 29...
  • Page 30 VERIFY GASKET IS IN PLACE. SECURE WITH (4) SCREWS PREVIOUSLY REMOVED. 3. SECURE COVER PLATE WITH (7) SCREWS PREVIOUSLY REMOVED. 3. SECURE COVER PLATE WITH (5) SCREWS PREVIOUSLY REMOVED. 30 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 31: Approved Vent Systems

    This appliance is equipped for use with a 4” exhaust by 6-5/8” air intake co-axial vent pipe system. This appliance is approved for use with Kozy Heat 4” x 7” #700 Series Flexible Direct Vent system (horizontal terminations only). Refer to Section 7.9 #700-2 Series Direct Vent Termination Kit(s) on page 43 for venting components and installation instructions.
  • Page 32: Restrictor Assembly And Installation

    SLIDE RESTRICTOR INTO EXHAUST PIPE ON TOP OF FIREPLACE WITH TABS POINTING TOWARDS YOU PRIOR TO ATTACHING VENTING Figure 7.1, Restrictor Assembly and Installation 32 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 33: Vent Heat Shield Assembly Installation

    HORIZONTAL VENT VERTICAL VENT HEAT SHIELD HEAT SHIELD Figure 7.4, Vent Heat Shield on a Corner Installation ATTACHMENT SCREWS Figure 7.2, Installed Heat Shield Assembly #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 33...
  • Page 34: Coaxial Rigid Pipe Venting Configurations

    Section 7.2 Approved Vent Systems on page 7.6.1.1 Vertical Terminations Minimum / Maximum Vertical Venting: 3’ (914mm) minimum vertical length / 50’ (15.24m) maximum vertical length + termination cap 34 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 35 (i) Minimum Vertical / Maximum Horizontal Terminations: 90° horizontal elbow + 6” (152mm) minimum horizontal run / 8’ (2.4m) maximum horizontal + termination cap #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 35...
  • Page 36 (2) 45° degree elbows may be used in place of (1) 90° elbow. manufacturers listed in Section 7.2 Approved Vent Systems on page Figure 7.5, Natural Gas & Propane - Top Vent Combination Venting (V/H) 36 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 37 (ii) Minimum / Maximum Combination Venting Vertical Terminations: 90° vertical elbow + 3’ (914mm) minimum vertical length / 50’ (15.2m) maximum vertical length + termination cap #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 37...
  • Page 38 • (2) 45° degree elbows may be used in place of (1) 90° elbow. Figure 7.6, Natural Gas - Rear Vent Combination Venting (H/V) 38 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 39 • 25’ (7.6m) maximum vertical rise + 25’ (7.6m) maximum horizontal run = 50’ (15.2m) of total length • Maximum of (5) 90° elbows. #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 39...
  • Page 40 Section 7.2 Approved Vent Systems on page • (2) 45° degree elbows may be used in place of (1) 90° elbow. Figure 7.7, Combination Rear Venting - Propane 40 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 41: Class A Chimney/Masonry Chimney Conversion

    4” aluminum flexible pipe / 50’ (15.24m) maximum length of 4” aluminum flexible pipe + top adapter + termination cap 10’ (3.05m) 24” (610mm) #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 41...
  • Page 42: Coaxial To Co-Linear Chimney Conversion

    (3.05m) minimum length of 3” x 3” aluminum flexible pipe / 50’ 10’ (3.05m) (15.24m) maximum length of 3” x 3” aluminum flexible pipe + termination cap (iii) 24” (610mm) maximum 42 VENTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 43: 700-2 Series Direct Vent Termination Kit(S)

    (OPTIONAL) insulate the wall thimble with any unfaced insulation Figure 7.9, Installation and Assembly of #700-2 Series products listed as non-combustible per ASTM E 136. #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces VENTING 43...
  • Page 44: Fireplace Setup

    Lift the bottom frame up and out of slots on firebox floor. To reinstall, align the tabs on the bottom frame and lower into position. Reinstall safety barrier. Figure 8.1, Bottom Frame Removal 44 FIREPLACE SETUP Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 45: B36-500 Log Set Installation

    Position the ember panel in front of the burner. Figure 8.2, Base Logs Figure 8.3, Installed Log Set #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces FIREPLACE SETUP 45...
  • Page 46: Control Board Removal And Installation

    11. Reconnect electrical power. 12. Verify proper log placement, operation of fireplace, and any electrical components. Figure 8.4, Control Board Removal and Installation 46 FIREPLACE SETUP Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 47: Electrical Information

    Follow instructions included with assembly. • If an optional component is to be used, run low-voltage wires from control module to the location of component. #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ELECTRICAL INFORMATION 47...
  • Page 48 MALE END SENSOR BATTERY PACK IPI/CPI SWITCH 886 PROFLAME PILOT BURNER Figure 9.2, Electronic Gas Valve Wiring Schematic with Thermostat or Wall Switch Wiring 48 ELECTRICAL INFORMATION Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 49 TH and TP-TH on gas valve Figure 9.4, Millivolt Gas Valve Wiring Schematic with Thermostat or Wall Switch Wiring #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ELECTRICAL INFORMATION 49...
  • Page 50: B36-075 Optional Fan Kit

    The fan will turn ON and OFF automatically as fireplace heats and cools. Adjust fan to desired speed while it is running. 50 ELECTRICAL INFORMATION Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 51 Black from receptacle Connect A to B, C to D, E to F, and G to H Figure 9.5, Fan Wiring and Connections #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ELECTRICAL INFORMATION 51...
  • Page 52: Operating Instructions

    OFF position. To access gas controls under the fireplace, remove the bottom Reinstall bottom frame. frame. Press the ON/OFF rocker switch to “OFF”. 52 OPERATING INSTRUCTIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 53 To operate the appliance, see the operating instructions and safety information on the previous page. Figure 10.2, HI/LO Pressure Knob #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces OPERATING INSTRUCTIONS 53...
  • Page 54: Lighting Instructions (#Bay-36-Mv)

    Push in gas control knob slightly and turn clockwise “OFF”. Turn off all electric power to the appliance if service is to be performed. Reinstall bottom frame. Remove bottom frame. 54 OPERATING INSTRUCTIONS Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 55 Refer to the lighting instructions on the previous page for lighting procedures and safety information. Gas control knob HI/LO pressure regulator knob Figure 10.3, Millivolt Gas Control Valve #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces OPERATING INSTRUCTIONS 55...
  • Page 56: Adjustment

    Disconnect hose and tighten the inlet (IN) pressure tap by Tap (B) (0.41 - 0.87 kPa) (1.59 - 2.48 kPa) (B) MANIFOLD (A) INLET PRESSURE PRESSURE TAP Figure 11.1, Pressure Check Taps 56 ADJUSTMENT Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 57 (0.41 - 0.87 kPa) (1.59 - 2.48 kPa) tighten. (A) INLET PRESSURE TAP (B) MANIFOLD PRESSURE TAP Figure 11.2, Pressure Check Taps Locations (Millivolt Gas Valve) #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ADJUSTMENT 57...
  • Page 58: Burner Flame Adjustments

    Venturi settings(s) closed too far. Open venturi(s) slightly Figure 11.3, Burner Venturi OR gas pressure too high - check manometer settings Figure 11.4, Flame Appearance and Characteristics 58 ADJUSTMENT Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 59 Insert restrictor into the 4” (102mm) exhaust pipe with the tabs pointing towards you. Reinstall baffle using (4) screws previously removed. Reinstall all other components previously removed. #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces ADJUSTMENT 59...
  • Page 60: Troubleshooting

    Plugged main burner orifice Remove blockage. Pilot flame Verify the pilot flame is properly directed to ignite burner. See pilot flame troubleshooting above. 60 TROUBLESHOOTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 61 Check the vent pipes for leaks, and the vent cap for debris. Repair the system vent pipes or remove debris from vent cap, if necessary. No reaction to command Battery back up batteries low Replace batteries. #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces TROUBLESHOOTING 61...
  • Page 62: Continuous Pilot Ignition (Millivolt) System

    Pilot safety dropout Pilot flame is too high or too low. Clean pilot hood and adjust pilot flame for maximum flame impingement on thermopile. 62 TROUBLESHOOTING Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 63 Check the vent pipe for leaks, and the vent cap for debris. Repair vent system pipe or remove debris from vent cap if necessary. #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces TROUBLESHOOTING 63...
  • Page 64: Maintenance

    Performed by: Annually Frequency: Action: • Examination of the vent system is required. • The flow of combustion and ventilation air must not be obstructed. 64 MAINTENANCE Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 65: Burner And Pilot System

    Test and measure the flame failure response time of the flame safety system. It must de-energize the safety shutoff in no more than (30) seconds. Burner ori ce BURNER PORTS Figure 13.1, Burner System #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces MAINTENANCE 65...
  • Page 66: Replacement Parts List

    700-092 Burner Assembly B36L-135A Thermocouple 700-093 Hussong Manufacturing Co., Inc. P.O. Box 577 204 Industrial Park Drive Lakefield, MN 56150-0577 BAY-36-MV and BAY-36-LE 66 REPLACEMENT PARTS LIST Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces #BAY-36-LE & MV R.11 April 2021...
  • Page 67 FAN KIT Fan Kit B36-075 Hussong Manufacturing Co., Inc. P.O. Box 577 204 Industrial Park Drive Lakefield, MN 56150-0577 BAY-36-MV and BAY-36-LE #BAY-36-LE & MV R.11 April 2021 Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces REPLACEMENT PARTS LIST 67...
  • Page 69: Limited Lifetime Warranty

    • All parts and material except the items listed in the 30 day Kozy Heat gas appliance from the date of purchase to the original warranty and any exclusions or limitations that may apply. purchaser, that it is free of defects in materials and workmanship at *Hussong Mfg.

This manual is also suitable for:

Bayport 36 mvBay-36-leBay-36-mv

Table of Contents