Subscribe to Our Youtube Channel
Related Manuals for Hachette PACK 3
Summary of Contents for Hachette PACK 3
- Page 1 A L I E N spectacular scale EASY ASSEMBLY BUILD THE TERRIFYING XENOMORPH FROM ALIEN PACK 3 KITS 13 - 20...
-
Page 2: Table Of Contents
Keep away from children. If you suspect a magnet has been swallowed, seek medical help straight away. Hachette Partworks Ltd, 4th Floor, Jordan House, Some parts may have sharp edges, please handle them with care. - Page 3 A S S E M B L Y G U I D E K I T 1 3 : T H E H E A D A N D T H E S K U L L ( I I ) In this kit you will continue to assemble different parts of the Xenomorph’s head and skull.
- Page 4 K I T 1 3 : T H E H E A D A N D T H E S K U L L ( I I ) EXPERT ADVICE From this kit onwards, the Pipes provided will be attached to small numbered tabs which will allow for quick identi cation. Before adding them to the assembly, gently twist the tab to remove it from the piece.
- Page 5 K I T 1 3 : T H E H E A D A N D T H E S K U L L ( I I ) 13-5 13-1 Take the head assembly you worked on in pack 2 - kit 12 and orientate Head part 13-1, as shown.
- Page 6 K I T 1 3 : T H E H E A D A N D T H E S K U L L ( I I ) To finish, test-fit the tabs on Pipe R3 13-4 into the next three slots and glue 13-4 (R3) in place.
-
Page 7: K I
A S S E M B L Y G U I D E K I T 1 4 : T H E S K U L L & T H E R I G H T L E G ( I ) In this kit you will continue to add appendages to the skull as well as working on parts of the right calf. -
Page 8: K I
K I T 1 4 : T H E S K U L L & T H E R I G H T L E G ( I ) 14-2 (A1) Take the skull assembly which was worked on in the last kit and continue fitting the pipes on the right-hand side. - Page 9 K I T 1 4 : T H E S K U L L & T H E R I G H T L E G ( I ) 14-5 Finally, take the Calf Skin 14-1 14-5 and fit the four Magnets 14-5 14-5 into the circular recesses as...
-
Page 10: K I
A S S E M B L Y G U I D E K I T 1 5 : T H E S K U L L & T H E R I G H T L E G ( I I ) In this kit you will continue to add appendages to the skull as well as working on parts of the right calf. - Page 11 K I T 1 5 : T H E S K U L L & T H E R I G H T L E G ( I I ) Take the skull assembly you worked on in the previous kit. Check that the tabs on Pipe R4 15-3 fit correctly...
- Page 12 K I T 1 5 : T H E S K U L L & T H E R I G H T L E G ( I I ) 14-1 14-1 15-5 (R7) 15-6 (R6) 15-5 (R7) Take the right Calf Skin 14-1, Repeat the previous step to attach supplied with the previous kit, along Pipe R6...
-
Page 13: K I
A S S E M B L Y G U I D E K I T 1 6 : T H E S K U L L A N D T H E R I G H T L E G ( I I I ) In this kit you will continue to add appendages to the skull as well as starting work on building the right tibia. -
Page 14: K I
K I T 1 6 : T H E S K U L L & T H E R I G H T L E G ( I I I ) Take the skull assembly that you worked on in the previous kit. Check that the Pipe R8 16-2 fits... - Page 15 K I T 1 6 : T H E S K U L L & T H E R I G H T L E G ( I I I ) Repeat the previous step to fit the Pipe R10 16-4 underneath the other side of the Jaw 1-2.
- Page 16 K I T 1 6 : T H E S K U L L & T H E R I G H T L E G ( I I I ) 16-1 15-1 Take the Right Calf Skin 14-1 which was worked on in kit 14 and the Tibia parts 15-1/16-1.
- Page 17 A S S E M B L Y G U I D E K I T 1 7 : T H E R I G H T L E G ( I ) In this kit you will continue to assemble parts of the right tibia and leg. 17-1 17-2 17-3...
- Page 18 K I T 1 7 : T H E R I G H T L E G ( I ) 17-2 Place the Right Tibia 17-1 17-1 on the work surface and note from the diagram how Connector 17-2 fits into the oval recess on part 17-1.
- Page 19 K I T 1 7 : T H E R I G H T L E G ( I ) Repeat the previous step to add the remaining two Magnets 17-3 to part 4-4, 17-3 17-3 as shown. Again, it doesn’t matter which way up the magnets are tted.
- Page 20 A S S E M B L Y G U I D E K I T 1 8 : T H E R I G H T L E G ( I I ) In this kit you will continue to assemble parts of the right leg. 18-1 18-2 18-3...
- Page 21 K I T 1 8 : T H E R I G H T L E G ( I I ) 18-4 17-1 Take the right tibia assembly 17-1 that was worked on in the last kit along with the Tibia part 18-1. The two parts are joined together using the previously fitted Connector 17-2.
- Page 22 K I T 1 8 : T H E R I G H T L E G ( I I ) 18-4 18-4 18-2 The two sections are joined together using two Connectors 18-2 18-2, as shown. Secure the Connectors 18-2 in place using two 2.3x6mm screws 18-4.
- Page 23 K I T 1 8 : T H E R I G H T L E G ( I I ) EXPERT TIP: Magnets are used to hold some of the parts together. Consequently, it is important that the magnets are correctly orientated so that the parts are attracted to each other.
- Page 24 A S S E M B L Y G U I D E K I T 1 9 : T H E R I G H T R I B S In this kit you will start to assemble the right ribs and their support structure.
- Page 25 K I T 1 9 : T H E R I G H T R I B S 19-2 Take the Right Rib 19-2 insert it into the Rib Support 19-3, as shown. A raised screw socket on Rib 19-2 fits into a hole in the Support 19-3.
- Page 26 K I T 1 9 : T H E R I G H T R I B S EXPERT TIP: When tightening a screw into metal, the screw sometimes needs to cut a thread which makes it dif cult to turn. If this should be the case, turn the screw half a turn forwards and then a quarter turn backwards until the screw is tted in place.
- Page 27 A S S E M B L Y G U I D E K I T 2 0 : T H E R I G H T R I B S A N D T H E L E G ( I ) In this kit you will continue to assemble the right ribs and leg of the Xenomorph.
- Page 28 K I T 2 0 : T H E R I G H T R I B S A N D T H E L E G ( I ) 20-6 20-2 20-2 19-1 20-1 19-3 Place Right Ribs 20-1 20-2 on the work surface.
- Page 29 Connector 20-4 overhangs the end of Tibia 20-3, 20-4 fix in place with a 2.3x6mm screw 20-5. 20-3 ANOTHER RIB HAS BEEN FITTED KIT 20 AND PACK 3 ALONG WITH MORE PARTS FOR IS NOW COMPLETE THE RIGHT LEG.
Need help?
Do you have a question about the PACK 3 and is the answer not in the manual?
Questions and answers