Hachette U-BOAT U96 Assembly Instructions Manual
Hide thumbs
Also See for U-BOAT U96:
- Assembly instructions manual (21 pages) ,
- Assembly instructions manual (16 pages) ,
- Assembly instructions manual (19 pages)
Related Manuals for Hachette U-BOAT U96
Summary of Contents for Hachette U-BOAT U96
- Page 1 U 96 Pack 8 Kits 29-32 25 20 U-BOAT BUILD THE ICONIC WORLD WAR II U-BOAT...
- Page 2 Kit 29: Three more connectors Kit 30: The hull Kit 31: The first magnet Kit 32: Hull section © 2023/2024 Hachette Partworks Ltd. ALL RIGHTS RESERVED Not suitable for children under 14. Hachette Partworks Ltd WARNING: All parts belong to a kit.
- Page 3 Kit 29: Three more connectors After adding a marker label to a cable, you will connect it to the forward circuit board. Then, three connecting pieces are added to the hull structure and bow compartment bulkhead. 29-1 29-2 29-4 29-5 29-3 Parts reference list Part no.
- Page 4 Kit 29: Three more connectors STAGE 1 Connecting the cable 24-2 29-4 29-4 29-5 Peel the cable label 29-5 from the backing film and wrap it around Insert one of the ends of the cable 29-4 into port 6 of the PCB the cable 29-4 approximately 8mm from a connector.
- Page 5 Kit 29: Three more connectors 29-2 29-3 20-1 20-1 19-2 Connect the upper part of the connector 29-2 to the bow Now working from the other side of the hull, remove the compartment bulkhead 20-1 using a screw, as shown. screw from connector 19-2 and keep it aside as a spare.
- Page 6 Kit 30: The hull The next lower hull section is added to the assembly. Two pieces of cardboard are then folded to make a stand for the structure. 30-1 30-2 30-3 Parts reference list Part no. Name Screws 30-1 Lower hull section 30-2 Stand Dimensions...
- Page 7 Kit 30: The hull STAGE 1 Attaching the hull section 19-1 29-1 30-1 29-1 30-1 19-1 30-1 Take the lower hull section 30-1 and lay it on your work surface. Attach the hull section 30-1 to the connector 29-1 using four Note that the gap between the end and the transverse rib is screws through the free holes, as shown above.
- Page 8 Kit 30: The hull Fold the stand 30-3 along both folds, creating a rectangular tube. Insert the two tabs into the slots and press down gently to seat them. 30-3 Line up the two stands 30-2 30-3 as shown in the photo. Take the hull assembly and rest it across the stands, as indicated by the arrows.
- Page 9 Kit 31: The first magnet Upper deck parts and a compressed air cylinder are first assembled and then glued to the assembly above the bow compartment. The front bracket is attached to the model, and the first magnet inserted into the bracket. 31-1 31-2 31-3...
- Page 10 Kit 31: The first magnet STAGE 1 Assembling the upper deck pieces and compressed air bottle 31-1 31-1 31-2 31-2 Place both halves of the upper deck compartment 31-1 31-2 Glue the two halves 31-1 31-2 together, ensuring that they fit your work surface.
- Page 11 Kit 31: The first magnet STAGE 2 Installing the front bracket and magnet From above, slide the magnet 31-5 into the holding slot in the bracket 31-4 (see inset 31-4 picture). Then fit the bracket between the two connectors 29-3 on the starboard (R) side of the hull.
- Page 12 Kit 32: Hull section A new upper section of the hull is fitted with two connectors and then added to the assembly. A beam is then secured to the hull structure. 32-1 32-2 32-3 32-4 Parts reference list Part no. Name Screws 32-1...
- Page 13 Kit 32: Hull section STAGE 1 Installing the hull section and beam 32-3 32-3 32-1 32-1 Place the hull section 32-1 on your work surface, the interior side Fix the connector 32-3 to the hull piece 32-1 using two screws. facing up.
- Page 14 Kit 32: Hull section Take the beam 32-4 and fit it between the 32-3 two connectors 32-3 and 29-3, as shown. 32-4 29-3 Fix the beam 32-4 in place using two screws into connector 32-3 and another two into connector 29-3. 32-4 32-3 29-3...
Need help?
Do you have a question about the U-BOAT U96 and is the answer not in the manual?
Questions and answers