Page 1
Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs • Parts of the assembly will be • We do not approximately 24kgs. easier with 2 people. recommend the Please lift with care. use of power •...
Page 3
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020...
Page 4
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly.
Page 5
Assembly Instructions Drawer Assembly Step 1 www.youtube.com/watch?v=InNBV_uuMmo Prepare the 3 drawer fronts Screw 2 metal dowels into each of the drawer fronts Note: Tighten the metal dowels up fully against the panels. Step 2 Prepare the drawer sides Insert a small locking cam nut into the hole shown on the left drawer...
Page 6
Assembly Instructions Step 4 Fit the drawer base Slide the drawer base down the grooves in the drawer sides and down into the groove in the drawer front Step 5 Fit the drawer back Fit the drawer back between the drawer sides Make sure that the drawer base...
Page 7
Assembly Instructions Fitting Ball Bearing Runners Step 8 www.youtube.com/watch?v=yG4xtiJJeSg Prepare the left side Place 3 runners the left side shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw Slide the runner back the other way and fit the 2nd screw into...
Page 8
Assembly Instructions Step 9 Prepare the right side Place 3 runners the right side shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw Slide the runner back the other way and fit the 2nd screw into Finished...
Page 9
Assembly Instructions Step 11 Fit the plinth and the rail to the right side Push the plinth onto the right side Note: Support the rail secure it with screw until the left side has been Push the rail onto the fitted in the next step.
Page 10
Assembly Instructions Step 14 Squaring up a Chest and tting the Back Panel www.youtube.com/watch?v=FeaI6541z7o Fit the back The measurement from top corner X to bottom corner X must be Square up the unit by equal to the measurement from top corner Y to bottom corner Y making sure that measurement x to x equals y to y.
Page 11
Assembly Instructions Step 16 inside Fit the shelves to the surface bookcase ends Attach the 3 shelves to the bookcase ends p l a using 12 screws c h i s u r p l a f a c c h i s u r p l a f a c...
Page 12
Assembly Instructions Step 18 Choose desk layout Before going onto the next step, decide which way around you would like your desk to be. Place the 2 assemblies where the desk will be used, so that the unit Drawers on the left does not have to be moved once the top panel has been secured...
Page 13
Assembly Instructions Step 20 Fit the top Lift the top and push the 8 metal dowels fitted to the top down into the holes in the top edge of the sides and bookcase ends Use a screwdriver to tighten the 8 large locking cam nuts fitted to the sides and bookcase end panels...
Page 14
Assembly Instructions Step 21 WARNING! Fit the 2 overbalance In order to prevent overturning protector kits this product must be used with the 2 wall attachment devices provided To prevent possible overbalancing this unit must be secured to a Example suitable wall by fitting of the 2 overbalance Attach the...
A Guide to Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are supplied with your are suitable for supporting your unit.
Page 16
If they catch on the runner you may need to loosen them slightly. If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.