Table of Contents
Advertisement
Sub
Index
Object Name
Index
Upper Range Value (URV)**
0x0118
0x00
0x0119
0x00
SSC1 Set Delay
0x011A
0x00
SSC1 Reset Delay
0x011B
0x00
SSC2 Set Delay
0x011C
0x00
SSC2 Reset Delay
0x011D
0x00
AmbientTemp
0x011E
0x00
AnalogOutEnabled**
AnalogOutType**
0x011F
0x00
0x0120
0x00
Damping filter
RelayThresholdConfigura-
0x0200
0x00
tionValue
U=User, M=Maintenance, S=Specialist
MU= Measure Unit
*Available only in SIL 2 / PL d Relay output version
** Available only in SIL 2 / PL d Analog output version
*** Available only in T integrated version
7.5. LED behavior
The IL transducer has an RGB led on board used to show the status and functionalities of the device:
Table 11
Led behavior
Status/Event
OFF
SIO mode
IO-Link
Autozero command
Cal Mode
Safety related
Error/Warning
Non Safety related
Error/Warning
Relay threshold overtaking
80618_MAN_IO-LINK IMPACT_12-2019_ENG
Access
Length
(Bytes)
U
M
S
RO R/W R/W 2
RO R/W R/W 2
RO R/W R/W 2
RO R/W R/W 2
RO R/W R/W 2
RO RO RO 2
RO RO RO 1
RO R/W R/W 1
RO R/W R/W 2
-
R/W R/W 1
Led Color
Mode
-
Fixed
Green
Fixed
Green
Blinking
Blue
Fixed
Yellow
Fixed
Red
Blinking
Yellow
Blinking
Pink
Blinking
Data
Value
Value
Type
(example)
Range
UInt16
FS
33%FS...FS
UInt16
0
0...500
UInt16
0
0...500
UInt16
0
0...500
UInt16
0
0...500
Int16
0
-40...125
0: disabled
Boolean
1...255:
0...255
enabled
0x00--> no
analog
0x01-->
4...20 mA
Uint8
0...2
0x02-->
0,5...10,5
V
Uint16
0
0...1000
UInt8
80
10...100
Timing
Note
OFF
ON
100ms OFF
900ms ON
1s ON
If autozero command is accepted
Then OFF
ON
Until Cal mode disabled
500ms OFF
500ms ON
500ms OFF
500ms ON
500ms OFF
500ms ON
Gradient
Offset Unit Description
Rangeability functionality,
specifies the end value of
According
range for Analog output
to MU
0
MU
(limited from 33 to 100%
See
FS)
Table 10
SSC1 Delay time set (see
0,1
0
s
par. 7.6)
SSC1 Delay time reset
0,1
0
s
(see par. 7.6)
SSC2 Delay time set (see
0,1
0
s
par. 7.6)
SSC2 Delay time reset
0,1
0
s
(see par. 7.6)
1
0
°C
Temperature of electronics
Defines if the transducer
has Analog output (en-
1
0
-
abled) or not (disabled)
Selects type of analog
1
0
-
output.
Need restart to be effective
Process data (pressure)
filter; it affects both Digital
and Analog output
Limited to 1s (user have
0,001
0
s
to consider it for safety
function reaction)
0 = disabled
1 ms = not accepted
Defines value of Relay
threshold inserted by
1
0
%
user (needs confirmation
through sys command)
(see par.7.8)
21
Advertisement
Table of Contents
