gefran ILI Series Original Operating Instructions page 17

Table 6
Error and Warnings in Detailed Device Status
Event Code Event Type
- -
- -
- -
0x5000 Error
0x8C10 Warning
0x8C30 Warning
0x5100 Error
0x5100 Error
0x5100 Error
0x8CA0 Error
0x4210 Error
0x8C00 Error
0x8CA5 Error
0x8CA6 Error
0x8CA7 Error
0x18A4 Error
0x8CA1 Warning
0x8CA2 Warning
0x8CA3 Warning
0x8CA4 Error
Table 7 Other Events
Event Code Event Type
0x8DFD Error
0x8DFE Warning
0x8DFF Notification
0x189C Notification
0x189D Notification
0x189E Notification
0x189F Notification
0x18A0 Warning
0x18A1 Notification
80618_MAN_IO-LINK IMPACT_12-2019_ENG
Device Status Possible failure
Power supply cable
-
broken
- Device not connected
- Broken Power supply
Broken primary element
Failure or not connected primary
element
Pressure above 150%
of Span respect to
Out of Specification
factory zero at room
temperature
Pressure below
-50% of Span respect
Out of Specification
to factory zero at room
temperature
Failure Overvoltage
Failure Undervoltage
Out of specification Voltage variations
Error in program
Failure
sequence
Electronics overtem-
Out of specification
perature
Failure Error in input stage
Failure Error in RAM Memory
Failure Error in ROM Memory
Failure Error in CPU
The Relay did not
Failure open/close when
required
Not Functional Safety Related
Maintenance
Zero drift excessive
required
Process temperature
Out of specification
over limit allowed
Process temperature
Out of specification
below -30°C
Process temperature
Failure
sensor broken
Device Status Description
Failure Test event type "Error"
OK Test event type "Warning"
OK Test event type "Notification"
OK event for Autozero command successfully completed
OK event for Autozero command failed due to value (autozero) out of range
OK event for Autozero command failed due to function temporarily not available
OK event for Autozero command reset
OK event for Relay opened
OK event for Relay Threshold Changed, required confirmation*
Output behavior
IO-Link
Relay
Pressure value
Functional Safety Related
- Open
- Open
- Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 Open
16000 -
- -
- -
- -
Temperature =
-
10000
Reset Mode
Analog
LOW Remove failure
LOW Remove failure
LOW Remove failure
Send device to factory
HIGH
for repair
Switch off and on; if error
HIGH persists send to factory
for repair
Switch off and on; if error
HIGH persists send to factory
for repair
Switch off and on; if error
LOW persists send to factory
for repair
Switch off and on; if error
LOW persists send to factory
for repair
Switch off and on; if error
LOW persists send to factory
for repair
Switch off and on; if error
LOW persists send to factory
for repair
Switch off and on (leave
temperature cool down);
LOW
if error persists send to
factory for repair
Switch off and on; if error
LOW persists send to factory
for repair
Switch off and on; if error
LOW persists send to factory
for repair
Switch off and on; if error
LOW persists send to factory
for repair
Switch off and on; if error
LOW persists send to factory
for repair
Switch off and on; if error
- persists send to factory
for repair
Send device to factory for
-
maintenance
Switch off and on (leave
temperature cool down);
-
if error persists send to
factory for repair
Switch off and on (leave
temperature increase);
-
if error persists send to
factory for repair
Send device to factory
-
for repair
Note
Note
Valid for SIL 2 /
PL d Diagnostic
Valid for SIL 2 /
PL d Diagnostic
Valid for SIL 2 /
PL d Diagnostic
Only for SIL 2
/ PL d certified
transducer
Only for SIL 2
/ PL d certified
transducer
Only for SIL2/
PLd certified
transducer
Only for SIL 2
/ PL d certified
transducer
Only for SIL 2 /
PL d
Relay version
17