Advertisement

Quick Links

CORN
CORN
INSTALLATION MANUAL
AGCO
AGCO
3300
3300
09020402c
HEADSIGHT.COM | 574.546.5022

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AGCO 3300 CORN and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Headsight AGCO 3300 CORN

  • Page 1 CORN CORN INSTALLATION MANUAL AGCO AGCO 3300 3300 09020402c HEADSIGHT.COM | 574.546.5022...
  • Page 3 This icon designates an important instruction. Suggestions If you have any suggestions to improve this manual please call 574-546-5022 or email info@headsight.com. Disclaimers HEADSIGHT, HORIZON, PINPOINT, FORESIGHT, FEATHERSIGHT, TRUESENSE, TERRAHAWK, INSIGHT, the Headsight logo, the Horizon logo, and Terrahawk logo are trademarks of Headsight Harvesting Solutions.
  • Page 4: Table Of Contents

    Table of Contents Installation�������������������������������������������������������������������������������� Mounting Sensors �������������������������������������������������������������������������������02 AllRows �������������������������������������������������������������������������������� Sensor Wiring ����������������������������������������������������������������������������������03 DetermineWiringSystem ����������������������������������������������������������������� IndependentWiring���������������������������������������������������������������������������� OEIntegratedWiring��������������������������������������������������������������������������� IndependentWiring:HarnessLengthTable �������������������������������������������������� RemovingWiresforTightAccess����������������������������������������������������������� RoutingWiring�������������������������������������������������������������������������� IndependentWiring���������������������������������������������������������������������������� OEIntegratedWiring��������������������������������������������������������������������������� Install Horizon or Insight Controller�������������������������������������������������������������07 Install Light Wiring (Optional, Independent Wiring Only) ����������������������������������������07 Connecting Insight - Integrated Wiring only �����������������������������������������������������08 InstallInsight&AdapterHarness�����������������������������������������������������������������...
  • Page 5: Installation

    Installation Before working on combine or under header always: 1. Perform all combine and header manufacturer safety precautions for servicing header. 2. Insert stop to prevent movement of header. 3. Turn off combine and remove key from ignition. 4. Set combine parking brake. 5.
  • Page 6: Mounting Sensors

    Mounting Sensors All Rows 1. If equipped, remove the OE poly skid from the snout. 2. Bolt the Truesight sensor to the pocket bracket using provided hardwareSelct. • M 10 x 16 flange bolt at rear • M 10 x 25 carriage bolt and flange nut at front 3.
  • Page 7: Sensor Wiring

    Sensor Wiring Properly routing the wiring is the most critical part of the installation process. Please take time to ensure that you have allowed sufficient slack for motion as well as sufficient clearance from moving header parts or crop flow. Determine Wiring System Two different wiring systems are possible on the AGCO 3300 headers.
  • Page 8: IndependentWiring:HarnessLengthTable

    Independent Wiring: Harness Length Table 1. Select appropriate wiring from chart below and mark blue connector with sensor position. Standard Sensor Routing Header Width Left Left Center Center Right Center Right Up to – – ' and ’ ' and ’–Up ' and Removing Wires for Tight Access...
  • Page 9: RoutingWiring

    Routing Wiring Independent Wiring 1. Remove the black connector from the end of the extension harness. • Use appropriate length PFBxx 2. Route the loose pins end of the extension harness up through the snoot mounting plate from back to front. 3.
  • Page 10: OeIntegratedWiring

    7. Secure harness around pivot as shown. • Make sure to leave enough slack for full motion of snoot 8. Route the cable around rear hinge as shown. • Leave enough slack for motion • Use zip tie on bar •...
  • Page 11: Install Horizon Or Insight Controller

    3. Drill mounting holes using ½” drill bit. 4. Secure box to header using hardware provided. See the Headsight combine manual for more details about how to install the remaining wiring harness or control box and then connect each individual sensor. For Integrated wiring installs, see “Connecting Insight - Integrated Wiring Only”...
  • Page 12: Connecting Insight - Integrated Wiring Only

    Connecting Insight - Integrated Wiring only This section is only for installing Insight when connected to the OEM header wiring to use more than 2 sensors, use Foresight, or to add a 3rd or 5th sensor to a OE 2 or 4 sensor system. Install Insight &...
  • Page 13: ForLateModelCombines-InstallPowerAdapterOnHeader

    1. Route the Y521 (2 pin plug) up along the original combine harness to the single point. 2. Tie it near the single point for easy connection 3. Follow the instructions in the Headsight Agco combine manual to install the correct power wire for your model combine.
  • Page 14: Sensor Adjustment

    Sensor Adjustment Insert header stop to prevent movement. Changing Swing 1. Loosen the bolt A holding downstop. 2. Slide the downstop to new position in slotted hole. • Raising downstop will increase voltage swing and allow higher maximum cutting height •...
  • Page 15: Sensor Extensions

    Sensor Extensions Headsight recommends using the lowest setting that allows you to run as high as you desire. Increasing the length of the extension will reduce header control sensitivity. 1. Remove flange lock nut then remove arm and spring. 2. Install extension to sensor assembly with previously removed spring and flange locknut.
  • Page 16: Parts

    Parts Mounting Bracket and Harness ITEM QTY. PART NUMBER DESCRIPTION HT2290 Bracket, Outer Snout harness PFG5F PFG5R Hood harness PFBxx (xx=length) Extension Harness (10,17,23,33,38) B2290 Mounting Hardware...
  • Page 18 This Page Is Intentionally Left Blank...
  • Page 19: Statement Of Limited Warranty

    Headsight is for the sole purpose of identifying such goods and shall not create an express warranty that the goods shall conform to such description.
  • Page 20 574.546.5022 • 574.546.5760 4845 3B Rd • Bremen, IN 46506 info@headsight.com www.headsight.com...

Table of Contents