ZKTeco F18 Quick Start Manual
  1. Manuals
  2. Brands
  3. ZKTeco Manuals
  4. IP Access Controllers
  5. F18
  6. Quick start manual

ZKTeco F18 Quick Start Manual

Hide thumbs Also See for F18:
Table of Contents

Advertisement

Quick Links

Download this manual
Quick Start Guide
F18
Version: 1.0
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.

Advertisement

Table of Contents
loading

Related Manuals for ZKTeco F18

Summary of Contents for ZKTeco F18

  • Page 1 Quick Start Guide Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
  • Page 2 1 Overview Front Side 2.4 Inch TFT LCD USB Slot Reset Button Keypad & RF Card Read Area Door Bell & LED Indicator Fingerprint Sensor Speaker 正面 Back Bottom Star-shaped screw hole for fixing device to the back plate Tamper Alarm Button Terminal Block: 485+ 485-...

  • Page 3: Wiring Diagram

    2 Installation of Wall-mount Before the installation, please connect the cables to the connectors. 1) Fix back plate to the wall. 2) Mount the device on the back plate. 3) Secure the device and back plate. 3 Cautions 1) Power cable is connected after other wirings, and shut down the power firstly, when making some necessary checking.

  • Page 4: Lock Connection

    5 Lock Connection The system supports Normally Opened Lock and Normally Closed Lock. The NO LOCK (normally opened at power on) is connected with 'NO1' and 'COM' terminals, and the NC LOCK (normally closed at power on) is connected with 'NC1' and 'COM' terminals. Take NC Lock as an example below: 1)Device not sharing power with the lock 2)Device sharing power with the lock...
  • Page 5 7 RS485 and RS232 Connection RS232 Printer RS485 485+ 485+ Reader 485- 485- Note: RS232 for TA push firmware connect to the Printer. 8 Wiegand Reader Connection +12V +12V W D 1 IWD1 W D 0 IWD0 RLED Wiegand Card Reader GLED BEEP...

  • Page 6: Power Connection

    9 Power Connection 12VDC Recommended power supply: 1 12V ± 10%, at least 500mA. 2) To share the power with other devices, use a power supply with higher current ratings. 10 Ethernet Connection RJ 45 IP address: 192.168. .130 Subnet mask: 255.255.255.0 IP address: 192.168.

  • Page 7: User Registration

    11 User Registration When there is no super administrator set in the device, press M/OK to enter the menu. After setting the super administrator, the system will request for the administrator’s verification before entering the menu. For the security purpose, it is recommended to register a super administrator at the first time you use the device.
  • Page 8 12 Ethernet and Cloud Server Setting Press M/OK on the initial interface. Select COMM. and press M/OK. Then, select Ethernet on the Comm. Interface, press M/OK to set the network of the device. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface.
  • Page 9 13 Connect to ZKBioAccess IVS Software Device Side: Set ethernet and cloud server parameters refer to chapter 12. Note: The IP address should be able to communicate with the ZKBioAccess IVS server, preferably in the same network segment with the server address. Server address: Set the IP address as of ZKBioAccess IVS server.
  • Page 10 4) Click Add in operation column, a new window will pop-up. Select Icon type, Area, and Add to Level f rom each dropdown and click to add the device. Add Personnel on the Software 1) Click Personnel > Person > New. 2) Fill in all the required fields and click OK to register a new user.
  • Page 11 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.

Table of Contents