Related Manuals for ZKTeco F35
Summary of Contents for ZKTeco F35
- Page 1 Quick Start Guide Version: 1.1 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
-
Page 2: Terminal Block
Overview Microphone 25.35mm 75.00mm Camera Near-infrared Flash 2.4-inch Color Screen Hidden Touch Keypad Doorbell Button Card Reading Area Restart Fingerprint Sensor Speaker Front Bottom Side Back Terminal Block BELL- BELL+ Bell & Alarm Lock, Door Sensor, 12VIN PGND Exit Button & PGND Auxiliary Input Power In... -
Page 3: Installation Environment
Installation Environment Please refer to the following recommendations for installation. 10ft KEEP DISTANCE AVOID GLASS AVOID DIRECT AVOID USE OF REFRACTION SUNLIGHT ANY HEAT SOURCE AND EXPOSURE NEAR THE DEVICE Device Installation ① Stick the mounting template sticker to the wall and drill holes according to the mounting template sticker. ②... -
Page 4: Standalone Installation
Standalone Installation Smoke Alarm Detector Door Sensor Bell Printer Exit Button Reader Lock ZKBio CVAccess ZKBioTime 8.0 TCP/IP ★ Note: Features and parameters with mark are not available in all devices. Power Connection AC Adapter DC 12 3A Recommended AC Adapter 1) 12V ±... -
Page 5: Ethernet Connection
Ethernet Connection Connect the device and computer software via an Ethernet cable. As shown in the example below: ZKBio CVAccess ZKBioTime 8.0 Default IP address: 192.168.1.201 IP address: 192.168.1.130 Subnet mask: 255.255.255.0 Subnet mask: 255.255.255.0 Click on [COMM.] > [Ethernet] > [IP Address] , input the IP address and tap on [M/OK]. Note: In LAN, the IP address of the server (PC) and the device must be in the same network segment when connecting to the software. - Page 6 RS485, RS232 & DM10 Connection INWD0 INWD1 +12V 12VOUT 485+ RX232 485- 485A RS232 TX232 Printer RS485 Reader 485B WD1-OUT WD0-OUT INWD0 INWD1 RS485 AUX IN READER1 READER2 12VOUT RX232 485A TX232 AUX OUT LOCK VOUT POWER 485B RS485 DIP WD1-OUT DM10 WD0-OUT...
-
Page 7: Lock Relay Connection
Lock Relay Connection The system supports Normally Opened Lock and Normally Closed Lock. The NO LOCK (normally unlocks when power-on) is connected with 'NO' and 'COM' terminals, and the NC LOCK (normally locks when power-on) is connected with 'NC' and 'COM' terminals. Take NC Lock as an example below: 1) Device not sharing power with the lock 2) Device sharing power with the lock... - Page 8 After a successful pairing, click the device icon will ring the wireless doorbell. Note: 1) Each F35 only supports one wireless doorbell. 2) Wireless doorbell needs to be purchased by the customers themselves.
-
Page 9: User Registration
User Registration Press the [M/OK] key to access the main menu in case the device has not been configured with a super administrator. When creating a new user, assign the User Role as Super Admin. This action will prompt the system to request verification from the administrator before granting access to the menu. - Page 10 Method 2: Register on ZKBio CVAccess software: Please set the IP address and cloud service server address in the Comm. Menu option on the device. Click [Access] > [Device] > [Search] > [Search] to search the device on the software. When an appropriate server address and port is set on the device, the searched device displays automatically.
- Page 11 Method 3: Register on the phone: Click [Personnel] > [Parameters], enter ‘’http://Server address: Port’’ in the QR Code URL bar. The software will automatically generate a QR code. Scan the QR code or login onto ‘’http://Server address: Port/tokenAdreg’’ by the mobile phone to register users.
- Page 12 Ethernet and Cloud Server Settings Tap on [M/OK] > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface. Tap on [M/OK] >...
- Page 13 Connect to ZSmart After downloading and installing the ZSmart App on your phone, open the application and proceed to add the device by scanning the QR code. The steps for this process are as follows: On the device, tap on [M/OK] > [System] > [Video Intercom Parameters] > [QR Code Binding].
- Page 14 Visitors click the on the device to call and then phone will ring. The user can select accept or decline the call. After accepting the call, it will enter the video door phone interface.
-
Page 15: Onvif Settings
ONVIF Settings This function needs to be used with the Network Video Recorder (NVR). Set F35 to the same network segment as the NVR. 2. Tap on [M/OK] > [System] > [ONVIF Settings] to set the User Name and Password. - Page 16 4. Select the checkbox for the device you want to add and edit the parameters in the corresponding text field, then click on OK to add it to the connection list. 5. After successfully adding, the video image obtaining from the device can be viewed in real-time.
-
Page 17: Sip Settings
SIP Settings This function needs to be used with the indoor station. Local Area Network Use Set the indoor station to the same network segment as the device. On the SIP Settings interface, click on Account > Dtmf to set the value as same as the value of DTMF in the indoor station. - Page 18 Tap the icon on the device and click the calling shortcut keys to call the indoor station. Direct Calling On the SIP Settings interface, click on Calling Shortcut Settings > Call Mode > Direct Calling Mode> Add. Select the IP addresses of the indoor stations that you want to call, then the indoor stations will be displayed in the list.
- Page 19 Once the SIP is set up correctly, a green dot will appear in the upper right corner of the call page to indicate that the F35 is connected to the server. You can call the account name of the indoor station.
- Page 20 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.