Page 1
F18 User Manual Version: 1.0 Date: Dec. 2011 Introduction: This document mainly introduces the windows and operations of F18 model of 2.4 Inches color TFT products.
Page 3
About this manual Not all the devices have the function with ★ . The real product prevails. The photograph in this manual may be different from that of the real product. The real product prevails. Key functions of various models are different. Please read the key board instruction in appendix firstly.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 1. Operating Instruction 1.1 Abbreviated Operating Procedures Step 1: Install the device and power it up. Step 2: Enroll users by registering his/her fingerprints, passwords or card.
F18 User Manual V1.0 1.2 Introduction to Fingerprint Recognition technology Enroll fingerprint by pressing index finger, middle finger or ring finger . Proper press: Make finger center pressed on the sensor window Improper press: Upright Too lean Slant Too downward Please adopt the correct way to place the finger to avoid improper operation led to the identification performance degradation.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 1.3 About Verification Mode When the device is on initial interface, only after successful fingerprint or password or Card verification, user can save attendance record on the device. Initial Interface (As shown below): ...
Page 12
F18 User Manual V1.0 (1) 1:N fingerprint matching Verify the fingerprint pressed on the sensor at present with all fingerprint data in the fingerprint reader. Step 1: Press fingerprint properly on the sensor on initial interface. Step 2: If device says ‘Thank you”, the verification is completed.
Page 13
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. (2) 1:1 fingerprint match(User ID+fingerprint) Verify the fingerprint pressed on the sensor at present with the fingerprint related with user number. Use this method when it is difficult to identify user’s fingerprint.
Page 14
F18 User Manual V1.0 Step 3: If device says ‘Thank you”, the verification is completed. Notice: If device says “Please press again”, return Step 2 for the second operation. - 6 -...
Page 15
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. If device says “Error ID”, that means you input ID number is wrong, please return Step 1 for the second operation. Password Matching Step 1: Input User ID of employee to be verified on initial interface.
Page 16
F18 User Manual V1.0 Step3: Input password when the interface appears. Step 4: If device says ‘Thank you”, the verification is completed. - 8 -...
Page 17
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. When the screen displayed "password error" and "Input password again" as shown below: - 9 -...
Page 18
F18 User Manual V1.0 Please return Step 3 input password again for the second operation. Ranges of the input password time is 0~9. Employee can set default time what you want. For details please refer to 4.4 Display Setting. ...
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. Step 3: If the card has not registered yet, prompt that card is not registered. 1.4 Connection with PC The device only records attendance time. The statement can be disposed by software on PC.
Page 20
F18 User Manual V1.0 Subnet mask: Default subnet mask as 255.255.255.0. You can modify it if it is necessary. Gateway address: Default gateway address0.0.0.0. You can modify it if it is necessary. Network speed: There are three options: ATUO, 10M, and 100M.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. is set, input corresponding numerical value on connection interface of PC software. Set device: Enter Menu-Communication option to set the following items: Device ID: Set it in “Security”.
Page 22
F18 User Manual V1.0 Communication: Set up communication parameters between the equipment and the PC, including IP address, gateway, subnet mask, baud rate, device number, communications password etc. System: Manage the data and set the system parameters, including basic parameters, interface parameters, fingerprint and attendance parameters, to maximize meet user’s needs in the functional, display and other areas.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 2. User Management The user’s basic information on the device includes fingerprint, password and management access. In company’s attendance management, for employee’s change, the information on the device also needs modification.
Page 24
F18 User Manual V1.0 Notice: Only some models have name and card options. ID.NO: Staff's attendance number. FP (Fingerprint): enroll employee’s fingerprint. Ten fingerprints can be enrolled at most. The employee with fingerprint enrolled can use fingerprint to record attendance.
Page 25
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. may entry the menu operation; after the manager is appointed, anyone is unable to entry the menu until the manager status is confirmed, after the success can entry the menu:...
Page 26
F18 User Manual V1.0 Enroll password Input password (1~8) according to device’s prompt, and press OK to verify it. Then press OK save it or press ESC to exit without saving it. After saving, display will be on the device, which means the password has been set.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. number will display on the register button. Privilege setting Scroll the▲/▼ key and local cursor on the "Privilege" option box, scroll key to choose privilege. Save/exit user registration To confirm the registration information is correct, after getting confirmation, save it.
Page 28
F18 User Manual V1.0 Notice:1) means this employee is the administrator. means password has been enrolled. means ID Card has been enrolled. 2) The picture may be different from your device. The real product prevails. Press menu on the above interface, and the operating menu will pop out: Press ▲/▼...
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 2.2.1 Search user If many users are enrolled, in order to find an employee quickly, the device has provided “User ID” to search the employee. Press menu on manage user interface to get operating menu.
F18 User Manual V1.0 Notice: The picture may be different from your device. The real product prevails. Press ▲/▼ to read attendance record. Press OK/menu to query detailed information. Then press “ESC” to return to manage user interface. 2.2.3 Edit user Edit user information saved in the device.
Page 31
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. fingerprint, password or card. Use ▲/▼ or query user on manage user interface to select employee to be edited. Then press menu to select “edit” or press shortcut to verify it, and all enrolled information can be displayed on the device: ...
F18 User Manual V1.0 2.2.4 Delete user “Del user” is to delete employee’s partial information or all information from the device. It is used when the following states happen: 1) When employee’s fingerprint or password is not needed any more.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 2.2.5 Add user In order to add user conveniently for operator, add user is configured here. The function is the same as that of 2.1 add user.
Page 34
F18 User Manual V1.0 1. Enrollment Step 1: Select enroll card and then press OK. Step 2: press keyboard to input the number to be enrolled(if the number has been there already, the device will prompt you to copy the information to the card.), and then press OK.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. Sway the card in the induction area. After the device inducts the card, move the card off. When the verification is successful, the device will give prompt.
Page 36
F18 User Manual V1.0 Step 3: Press finger properly three times. Step 4: Device prompts “please show card”. Step 5: Put the card in the induction area, waiting for the device to read fingerprint data into card until the enrollment succeeds.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 2.3.3 Clear card information Delete all the information in the card being operated at present. Operation: Put the card in the induction area, waiting for device to delete all the information in the card.
F18 User Manual V1.0 Press ▲/▼ to select “only copy user information” or “copy user information and fingerprint”, and then press OK. 2.3.5 Set card parameter value Set password of Mifare card and decide whether the information should be saved or not.
Page 39
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. card can only be used on this device. Save the information: Decide whether to save the enrolled information to the device when enrolling card or fingerprint card. “No” means the information is only saved in the card.
F18 User Manual V1.0 2.4 Access Control Option★ Access control option is to set user’s open door time zone, control lock and related device’s parameters. If the device support external facial instrument, it can not support the camera and advanced access control at the same time.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 2.4.1 Time Zone Setting Time zone is the minimum unit of access control option. The whole system can define 50 time zones. Every time zone defines seven time sections (namely, a week).
F18 User Manual V1.0 Input time zone number. If the enrolled time zone has number already, then the time zone setting will displayed automatically. Press ▲/▼, to move the cursor to the input box, press numeric key on small keyboard to input value. Then press Menu to save it and press ESC to exit.
Page 43
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. Press ▲/▼ to select add. Press ▲/▼ to move cursor to the input box. Press numeric key on small keyboard to input the value. After setting, press Menu to save it. Then press ESC to exit.
F18 User Manual V1.0 Press ▲/▼ to move cursor to the input box. Press numeric key on small keyboard to input the value. After setting, press Menu to save it. Then press ESC to exit. Delete holidays Select the line to be deleted. Press Menu to select delete in operating menu.
Page 45
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. Add group time zone Press Menu to get operating menu. Press ▲/▼ to select add. For example, to add a group whose time zone is 2 and 3, as shown below: - 37 -...
Page 46
F18 User Manual V1.0 Notice: 1) If holiday is effective, only when there is intersection between group zone and holiday time zone, can the group member open the door. 2) If holiday is ineffective, the access control time of group member won’t be affected by holiday.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. In the Access Group setting interface, select the line to be deleted. Press Menu to select delete in operating menu. 2.4.4 Set Unlock Combination Make various groups into different access controls to achieve multi-verification and improve security.
Page 48
F18 User Manual V1.0 Press ▲/▼ to move cursor to the input box. Press numeric key on small keyboard to input value. After setting, press Menu to save it. Then press ESC to exit. Edit unlock combination Select the line to be edited. Press OK directly or press Menu to select edit in operating menu.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. menu. 2.4.5 Access Control Parameters Set device control locks and related device parameters. Lock driver time length: Device control electronic lock is in enabling time.
F18 User Manual V1.0 2) If time zone of NO or NC has no definition, the device will prompt it and add the definition in time zone setting. Operation: Press Menu -> User Management -> Access Setting -> Access Control Parameters: Press ▲/▼to move cursor to the item to be set.
Page 51
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 1:1 Trig: if select “Yes”, when user use 1:1 match mode, alarm signal will come out. Or there is no alarm signal. 1: N Trig: if select “Yes”, when user use 1: N match mode, alarm signal will come out.
F18 User Manual V1.0 ★ Anti-passback Setting 2.4.7 【overview】 Sometimes, some illegal person follows the employee into the gate, which will bring security problem. To prevent such risk, this function is enabled. In record must match out record, or the gate won’t be open.
Page 53
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. The choice of Machine models: Press ▲/▼ to switch the input box. Press to modify the setting. Select Anti-Out, refer to out anti-pass back, only user’s last record is in-record, the door can be open.
Page 54
F18 User Manual V1.0 will trigger the alarm signal as illegal access. Out: New user’s first time access will pass. In anti-passback mode not restrict of IN. In-Out anti-passback (APB-Out/In): New user’s first time access will pass. Only user’s last record is out-record, can the door be open when he/she want IN.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 3. Communication Option When the device and PC are used to transmit data, it is necessary to use communication wire to set communication parameters in the device. When the device is in communication, “communicating…”...
F18 User Manual V1.0 Device IP address: IP is 192.168.1.201 by default. You can modify it if it is necessary. But it cannot be the same with that of PC. Subnet mask: It is 255.255.255.0 by default. You can modify it if it is necessary.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 485 is recommended. RS232: Whether use RS232 to communicate. Select “ON” if RS232 is to be used. RS485: Whether use RS485 to communicate. Select “ON” if RS485 is to be used.
F18 User Manual V1.0 Device ID: 1—254. If RS232/RS485 is used, this ID needs to be input on the software communication interface. To improve the security of attendance data, connection password needs to be set here. Connection password must be input when PC software is to connect device to read data.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 3.4.1 Input configuration User defined format: User defined Wiegand input format Bit digit: Wiegand data digit length Pulse width: Pulse width is 100 microseconds by default, which can be adjusted from 20 to 800.
F18 User Manual V1.0 Input the name of user-defined format. Press ▲/▼to move cursor to the item to be set. If it is the input box, press numeric keys on small keyboard to input the value. If it is the roll box, press to switch the values.
Page 61
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. Input the name of user-defined format. Press ▲/▼to move cursor to the item to be set. If it is the input box, press numeric keys on small keyboard to input the value.
F18 User Manual V1.0 4. System Option Set system parameters to meet user’s demand as many as possible. 4.1 System parameters 1: 1 matching threshold value: The similarity of ID + fingerprint verification and the enrolled template 1: N matching threshold value: The similarity of verification and the...
Page 63
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. Time format: Time format displayed on initial interface. Press set 24H or 12H. Date format: Press to select format. The fingerprint sensor supports ten date format: YY-MM-DD, YY/MM/DD, YY.MM.DD, MM-DD-YY, MM/DD/YY, MM.DD.YY, DD-MM-YY, DD/MM/YY, DD.MM.YY and YYYYMMDD.
F18 User Manual V1.0 Press ▲/▼ to move cursor to the input box. Press numeric key on small keyboard to input the value. If it is the input box, press numeric keys on small keyboard to input the value. If it is the roll box, press switch the values.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. data for how to upload the propaganda pictures.) Operation: Press “▲/▼” to preview the propaganda pictures in the device. Click OK to delete all these pictures. After deletion, the next picture will appear.
F18 User Manual V1.0 4.4 Display Setting Press ▲/▼ or to move cursor to the input box. Press numeric key on small keyboard to input the number. After setting, press menu directly to save the setting and return to the last interface. Press “ESC”...
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 4.4.3 Picture cycle interval Picture cycle interval means how soon will the picture be changed (effective value is 3~999 seconds.) Display propaganda picture: User can display some propaganda pictures on the screen.
F18 User Manual V1.0 interface success, machine displayed: "Standby Interface modified success ". T hen you should restart the device. Notice: "4.4.3 Picture cycle interval" and "4.4.4 Clock display delay" functions are fit use common mode of interface style only.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. keyboard definition to that of factory. Reset bell option: Only reset bell option to factory state. Reset other parameters: only reset communication option, system parameter and interface option and so on to factory state.
Page 70
F18 User Manual V1.0 Fingerprint image display: Select whether to display the fingerprint image on the screen when it is enrolling or verifying there are 4 options: display upon both enrollment and verification, only display upon enrollment, only display upon verification, not display upon enrollment and verification.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 5. Date Time 5.1 Date Time option Accurate attendance time is based on accurate time date. Enter time date to set options: Operation: Press ▲/▼...
Page 72
F18 User Manual V1.0 The regulations are different in different countries. At present, nearly 110 countries adopt DLST. To meet the demand of DLST, a special option can be customized on our RF Card Time & Attendance recorder. Make the time one hour forward...
Page 73
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 3) Press /“OK” to save setting. Press “ESC” to exit without saving. - 65 -...
F18 User Manual V1.0 6. PenDrive Management Import user information, fingerprint template, attendance data and so on in the device to attendance software or import user information and fingerprint to other devices through U disk. 6.1 Download data 1. Download attendance data Save all attendance data in the device to U disk.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. device ID). 2. Download user data Save all users’ information and fingerprint in the device to U disk. Operation: Insert USB flash disk into USB slot of the device, press “▲/▼” to download user, then user.dat (user information) and template.dat (fingerprint template) will be saved in U disk.
Page 76
F18 User Manual V1.0 Insert U disk into USB slot of device. Press “▲/▼” to preview the pictures of U disk. If you want to upload the picture, click OK. Then the next picture will appear automatically. After upload, press ESC to exit.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 7. Auto Test The device can test various modules automatically to help operator to judge the module with fault quickly. Auto test include TFT display Test, Audio Test, Keyboard Test, Sensor Test and RTC Test.
F18 User Manual V1.0 Press OK to continue and press ESC to exit. 7.3 Keyboard test The device can automatically test various keyboards to see whether the keys work normally or not. Press any keyboard on the test interface (except for OK and ESC) to check whether the pressed keyboard is in accordance with that displayed on the screen.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 8. Query Record Employee’s attendance records will be saved in the device. For convenience, query record function is provided. According to user’s input query condition, the record will be displayed on the screen for user to check.
Page 80
F18 User Manual V1.0 Press “▲/▼” to move the cursor to the line to be queried. And press OK to check attendance record. For example, the detailed attendance information of employee 10001 on May8th as follows: At the bottom of the screen, there are some remark, and the capital...
Page 81
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. It is the attendance status. The code displayed in the list is the status code. And status name will be displayed in the information column. - 73 -...
F18 User Manual V1.0 9. System Information Use system information to check the current device’s saving status, its version information and so on. 9.1 Record capacity Display the count of enrolled users, administrator, password enrollment, the current enrolled fingerprint and the current saved attendance record.
Page 83
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. - 75 -...
F18 User Manual V1.0 10. Appendix 10.1 Keyboard Different device has different kinds of keyboard, and the function of the keyboard is different. Please check the fallows: Keyboard type 1: function Numeric 1. 0~9 , used to input employee number, password and so 2.
Page 85
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. Keyboard type 2: function Numeric 1. 0~9,used to input employee number, password and so 2. 0 on manage user interface is shortcut of “query user”. ▲...
Page 86
F18 User Manual V1.0 Keyboard type 3: function Numeric 1. 0~9,used to input employee number, password and so 2. 0 on manage user interface is shortcut of “query user”. ▲ 1. Upward. 2. Shortcut. ▼ 1. Downward. 2. Shortcut. 1. Right.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. 10.2 USB USB Host The device will may be used as USB Host to exchange data with external U disk. The data transmission speed is quick, the traditional fingerprint machine only supports the RS232, RS485 or Ethernet way data transmission, when as a result of physical condition limit, data quantity big, and the data transmission cost quite long time.
F18 User Manual V1.0 fingerprint or password verification in 10 minutes. For example: the employee with User ID of 1 can check his intraday attendance record by pressing after fingerprint verification. Notice: The picture may be different from your device. The real product prevails.
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. The picture’s resolution is 320 wide and 240 high. It is better not to be more or less than it. The propaganda pictures’ count should be 10 at most. If you want it, please contact our businessman or technician.
F18 User Manual V1.0 10.6 Web time & attendance ★ Summary The T & A system is based on Web Server technical, use Page Request technical to process and manage data, it integrate many feature ,such local data collection ,...
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. Fully compatible with our company Inc program WEB Server platform may be fully compatible with current program each other entirely is mutually beneficial, ability to much more flexible to meet customer need.
F18 User Manual V1.0 This function can be set in the fingerprint machine option, Press Manu key, enter the Date Time. In the XX Month XX Date XX minute move forward an hour, and that in the XX Month XX Date, XX Minute move Back an hour.
Page 93
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. You can set every few hours to synchronize. (With range of 0-99, only the device is set as master unit, this setting is valid) 2) Connection Choose the master unit and slave unit.
F18 User Manual V1.0 10.11 About the human rights privacy statement Dear customer: First thank you for using Multi-biometric identification product we design and produce. As one of the global famous fingerprint identification core technology provider, we are constantly carrying on the development and research, also we believe such action is necessary to: (a) comply with the law or legal process served on Our company;...
Error! Use the Home tab to apply 标题 1 to the text that you want to appear here. not any legal liability for any damage it cause. Note: There are limited rights to privacy and human rights in the Chinese Constitution. The personal dignity of citizens of the People's Republic of China is inviolable and further, that insult, libel, false accusation or false incrimination directed against citizens by any means is prohibited, the...
Page 96
F18 User Manual V1.0 The toxic and harmful substances or elements Part name Cr6 + PBDE ○ ○ ○ ○ ○ × resistor ○ ○ ○ ○ ○ × capacitor ○ ○ ○ ○ ○ × inductance ○ ○ ○...