ZKTeco F18 Installation Manual

F18 Installation Guide
1. Equipment Installation
Wiring Hole
Fixing Hole Fixing Hole
F18 Mounting Paper
(only for your reference)
In st ru ct io n fo r th e Mo un ti ng P ap er
Be fo re t he d ev ic e is f as te ne d, p le as e
st ic k th e pa pe r to t he p la ce w he re y ou
wa nt t o in st al l it , th en m ak e ho le s an d
la y ca bl es a cc or di ng t o th e mo un ti ng
pa pe r.
10
11
12
13
Fixing Hole Fixing Hole
(1) Post the mounting template on the (2) Remove the screw on the
wall. Drill the holes according to
the marks on the template (holes
for screws and wiring).
(4) Fix the plastic pad and the back (5) Tighten the screw on the bottom,
plate on the wall according to the
mounting paper.
2. Structure and Function
RS485 TCP/IP
⑦
⑤
RS232/RS485 Converter
EXIT
④
BUTTON
①
⑥
②
Lock Sensor Exit Button
Reader
Bell
③
Alarm
Version: V1.1 Date: Nov. 2011
(3) Take away the back plate.
bottom of device.
fix the device to the back plate.
Access Control System Function
(1) If a registered user verified, the device will export the
signal to unlock the door.
(2) Door sensor will detect the on-off state If the door is
unexpected opened or improperly closed, the alarm signal
(digital value) will be triggered.
(3) If the d evice is removed i llegal , it will output an ly
alarm signal.
(4) External card reader is supported.
(5) External exit button is supported, it is convenient to
open the door inside.
(6) External door bell is supported.
(7) Supports RS485 TCP/IP , modes to connect
PC can manage multiple devices.
3.Lock Connection
(1) Share power with the lock:
+
-
DC12V
NC LOCK
-
+
(2) Does not share power with the lock:
+
-
DC12V
+
-
DC Power
NC LOCK
(1) The system supports NO LOCK and NC LOCK. For example the NO LOCK (normally open at
power on) is connected with
on) is connected with 'NC'
(2) When the Electrical Lock is connected to the Access control System, you need to parallel one FR107
diode (equipped in the package) to prevent the self-inductance EMF affecting the system, do not
reverse the polarities.
4. Other Parts Connection:
Door Bell
Exit Button
Alarm Power
-
+
Alarm Voltage output ≤ DC 12V
with PC. One
①:
'I': device output current, '
+
+12V
GND
-
BELL-
BELL+ DC12V
SEN
GND
-
BUT
FR 107
NO1
+
COM1
FR 107
NC1
NO LOCK
NO2
COM2
+
+12V
-
GND
DC12V
BELL-
-
BELL+
FR 107
SEN
+
GND
NO LOCK
BUT
-
NO1
COM1
+
NC1
+
FR 107
NO2
COM2
DC Power
' NO' and COM terminals, and the NC LOCK(normally close at power ' '
and COM' terminals. '
5. Power Connection:
BELL-
Input DC 12V, 500mA (50mA standby). Positive
BELL+
is connected with '+12V', negative is connected
SEN
with 'GND' (do not reverse the polarities).
GND
EXIT
BUTTON BUT
NO1
COM1
NC1
Door Sensor
NO2
COM2
Alarm
U ': lock voltage, ' I ': lock current
LOCK LOCK
！
Warning: No operating with power on
+12V
GND
Device shares power with the lock:
BELL-
BELL+
>1A... ①
U =12V, I-I
LOCK LOCK
SEN
GND
And the distance between the lock
BUT
and the device is equal or less
NO1
COM1
than 10 meters.
NC1
NO2
COM2
+12V
Does not shares power with the lock:
GND
≤1A;
BELL- A. U =12V I- I
LOCK LOCK
BELL+
≠12V;
B . U
LOCK
SEN
C. The distance between the lock and
GND
BUT
the device is more than 10 meters.
NO1
COM1
NC1
NO2
COM2
+
+12V
-
GND
DC12V