Summary of Contents for Maytronics Dolphin Wave 200XL
Page 1
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide October 2017...
Page 2
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Release History Prepared by Approved Date Revision History October 2017 Release History...
Table of Contents Overview ....................1 Robot Works Along Walls for a Long period of Time ......2 Slippery Pool Surface ................2 Robot Doesn’t Drive in Straight Lines ............ 3 Robot in Shape Mode ................3 Starting Point from a Shaped Wall ............3 Deviation Greater Than 10°...
Page 4
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide 12 Robot Drives Back before Capitalize the Line ........10 12.1 Pool Length Not Set Up Correctly ............10 12.2 Driving System Failure..............10 13 Robot Not Communicating with the Remote Control ......11 13.1...
Overview This Dolphin Wave 200 and 300 Pool Troubleshooting Guide is intended to guide technician in addressing problems associated with possible faults in the robot. The information in this guide is organized according to type of problem/symptom/component and the troubleshooting checks to be performed to pinpoint the source of the problem.
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide With regard to ... See ... Robot doesn’t complete lines Chapter 1 2, Robot Drives Back before Capitalize the Line, page 10 Robot drives width (instead of Chapter 6 , Robot Doesn’t Climb...
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Robot Doesn’t Drive in Straight Lines ➣ In this chapter… Robot in Shape Mode page 3 Starting Point from a Shaped Wall page 3 Deviation Greater Than 10° Degrees page 3 Robot in Shape Mode If possible, change the scanning mode to “Rectangular”.
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Not Enough Space between Lines ➣ In this chapter… Flat Pool Floor page 4 Sloped Pool page 4 Flat Pool Floor If the pool floor is flat and is not enough space between the lines, change...
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Sloped Pool Floor If the robot works "Down the slope," change the scanning direction to "Up the slope." (Wave 300 only) "Down the slope" "Up the slope" Change the line spacing to Medium or Fine (see change the line...
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Robot Leaves Unclean Spots in the Pool ➣ In this chapter… Robot in “Lines to” Scanning Mode page 6 Robot Doesn't Clean Areas Near Rounded page 6 Walls Niches, Tunnels, or Maze Areas in the Pool...
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Shaped Pool (No Rectangular Walls) Change the cleaning mode to “Maze scanning” and extend the cycle time (see change the cleaning mode to “Maze scanning” Video). Dirt Near Pool Wall Change the cleaning mode to “Crisscross” or clean the specific area via remote control (see change the cleaning mode to “Crisscross”...
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Worn Vacuum Strips Replace the vacuum strips (see wave 200XL Link). Wave 200XL vacuum strips Wave 300XL vacuum strip Robot Stays in the Deep Area ➣ In this chapter… Slope Greater Than 35° Degrees...
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Blocked Filter Clean the filter (see wave 200XL filter cleaning Video or wave 300XL filter cleaning Video). Slippery Pool Floor Check if the chemicals in the pool are balanced. Floating Cable Gets Stuck between Swimming Lanes Floats ➣...
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide 11.2 Alert LED On Refer to the error troubleshooting file (see wave 200XL Link). Robot Drives Back before Capitalize the Line ➣ In this chapter… Pool Length Not Set Up Correctly page 10...
Page 15
Dolphin Wave 200XL and 300XL Pool Troubleshooting Guide Robot Not Communicating with the Remote Control ➣ In this chapter… Distance between Remote Control and page 11 Caddy is Greater Than 50m Remote ID page 11 13.1 Distance between Remote Control and Caddy is...