Maytronics Dolphin Proteus DX3 - Swimming Pool Cleaner Manual

Helpful hints

• When working, the Power Supply should be placed in the shade.
• If the Dolphin is fitted with combined or wonder brushes, gently squeeze the brushes until they are soaked with water.
• Release minimal required floating cable length to ensure proper pool coverage.
  Leave excess cable rolled outside the pool.
• After each cleaning cycle wash the filters or cartridge. Clogged filters reduce scanning and cleaning efficiency
• To remove the kinks stretch the cable out completely and let it sit for at least a day in the sun.
• Store the pool cleaner in a shady place on its Caddy, if not on a caddy, place the pool cleaner upside down.

For a detailed manual (including videos):
manuals.maytronics.com/99996114-LES

Unit operation

Set Up

1. Attach the floating cable to the power supply.
   
2. Position the power supply at least 3.5m /12ft away from the edge of the pool.
   

Into the pool

3. Put the Pool Cleaner into the pool. Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions.
   

Operation

4. Turn the power supply ON. the pool cleaner will now operate until it has reached the end of the cleaning cycle.
   

Out of the pool

Cleaning the filter

It is highly reccomended to clean the filter basket after each cleaning cycle.
Note: Don't let the filter cartridges dry out before cleaning.

Unplug the power supply before servicing

1. Open the filter cover.
   
2. Lift up the basket.
   
3. Open the latch to release the bottom lid in order to remove the debris.
   
4. Clean the filter basket with a hose.
   

Storage

7. Coil the cable and store in a cool, dry place.
   Do NOT store the robot and its accessories where it will be exposed to direct sunlight, excessive heat or to frost.

Maintenance

Periodic filter cleaning

Dismantle the 2 ultra-fine filter panels of the outer basket according to the following steps:

1. Dismantle the 2 panels using your thumbs.
   
3. Clean the filter panels with a hose.
   
4. Assemble the filter panels.
   
5. Insert the clean filter basket and close the filter cover.
   

Cleaning the impeller

If you notice debris trapped in the impeller:
Unplug the power supply before servicing

Clean the debris trapped in the impeller opening, according to the following steps:

1. If the debris is not reachable follow the next steps.
   
2. Using a short screwdrive open the 2 screws.
   
3. Pull the impeller cover backwards to release it. Clean the debris trapped around the impeller. Assemble the impeller cover.
   

Cautions & Warnings

• Use the originally supplied power supply only.
• Do not use an extension cable in any case whatsoever.
• Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter.
• Keep the power supply out of standing water.
• Do not enter the pool while the Pool Cleaner is working.
• Unplug the power supply before servicing.
• Do not use the cable to take the pool cleaner out of the water.
• Use the Pool Cleaner in the following water conditions only: Chlorine Max 4 ppm;
  pH 7.0 - 7.8; Temperature 6 -34°C(43-93°F);
  NaCl Maximum = 5000 ppm.

Digital Power Supply
Input: 100-125 AC Volts
50-60 Hertz
120 Watt
Output: <30 VDC
IP 54

Specifications:
Motor protection: IP68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/16.4ft

Documents / Resources

References

• Dolphin Pool Cleaners' Manuals & Troubleshooting | Maytronics

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Maytronics Dolphin Proteus DX3 - Swimming Pool Cleaner Manual