Extron electronics NetPA AT Series Setup Manual
  1. Manuals
  2. Brands
  3. Extron electronics Manuals
  4. Recording Equipment
  5. NetPA AT Series
  6. Setup manual

Extron electronics NetPA AT Series Setup Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NetPA AT Series • Setup Guide
This guide provides basic instructions for an experienced technician to install the NetPA 502 AT and NetPA 1001-70V AT
Networked Power Amplifiers. Both the NetPA 502 AT and NetPA 1001-70V AT models are collectively referred to as NetPA AT in
this guide. For additional information and specifications, see the NetPA AT product page at www.extron.com.
WARNING: Installation and service must be performed by experienced personnel only.
AVERTISSEMENT : L'installation et l'entretien doivent être effectués par le personnel autorisé uniquement.
100-240V
0.5AMAX
50-60Hz
A
100-240V
0.5AMAX
50-60Hz
NetPA 502 AT and NetPA 1001-70V AT Rear Panels
Figure 1.
A
IEC AC power input, 100 to 240 VAC, 50-60 Hz
B
Gain adjustment (see
details)
C
Line out connector (see
details)
D
Remote connector (see
details)
E
RJ-45 Ethernet connector (see
page 2 for details)
Step 1 — Powering Down Equipment
Be sure that power to the NetPA AT is turned off first by disconnecting the power
NOTE:
Adjust the audio level to = (full attenuation) prior to powering the amplifier in
Turn off all other equipment and disconnect the power cables. Verify that the amplifier is disconnected from the power source
before proceeding.
Step 2 — Application Example and Mounting
For a typical application example, see Application Example in the user guide. For further mounting instructions, see Mounting the
NetPA AT in the user guide.
GAIN
LINE OUT
1
2
1
2
-4
-4
-6
-6
-2
-2
-8
0
-8
0
-12
+2
+2
-20
+4
+4
-
-
+6
+6
J
C
B
GAIN
LINE OUT
HPF
1
1
-4
-6
80 Hz
-2
-8
0
-12
+2
+4
-20
-
+6
OFF
step
12, on page 8 for
step 7
on page 2 for
step 6
on page 2 for
step 3
on
AT
8Ω/4Ω OUTPUTS
REMOTE
G
LINK
RESET
CLASS 2 WIRING
D
E F G
NetPA 1001-70V AT
AT
70 V OUTPUTS
REMOTE
G
LINK
RESET
CLASS 2 WIRING
F
Link indicator (see
Link Indicator LED
details)
G
Reset button (see
Resetting the NetPA AT
details)
H
Amplified stereo audio output connector (see
page 2 for details)
I
Amplified mono audio output connector (see
2 for details)
J
HPF (high pass filter switch) (see
details)
A
.
DProduct
NetPA 502 AT
1
2
H
I
on page 10 for
on page 9 for
step 4
on
step 4
on page
step 5
on page 2 for
step
8.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NetPA AT Series and is the answer not in the manual?

Questions and answers

Related Manuals for Extron electronics NetPA AT Series

Summary of Contents for Extron electronics NetPA AT Series

  • Page 1 DProduct NetPA AT Series • Setup Guide This guide provides basic instructions for an experienced technician to install the NetPA 502 AT and NetPA 1001-70V AT Networked Power Amplifiers. Both the NetPA 502 AT and NetPA 1001-70V AT models are collectively referred to as NetPA AT in this guide.

  • Page 2: Step 4 - Audio Output Connector

    NetPA AT Series • Setup Guide (Continued) Step 3 — Connecting the NetPA AT to the Network Using standard CAT cable, connect the RJ-45 connector of the NetPA AT to a LAN for digital audio transport (see Creating a Physical Dante Network on page 9).

  • Page 3: Product Category

    Product Category Step 8 — Powering On the Equipment ATTENTION: The amplifier must be powered on last. ATTENTION : L’amplificateur doit être allumé en dernier. Reconnect all power cables and switch on all other equipment before powering on the amplifier. The front panel power LED of the NetPA AT lights green.
  • Page 4 NetPA AT Series • Setup Guide (Continued) The Download Center page opens. — Download Center Dante Download Figure 3. Fill in the required fields. Click Download dantecontrollernxn.exe. Save the file to your desktop (or other known location). Locate and double-click the saved Dante Controller file to begin installation.
  • Page 5 Product Category From the toolbar, select Device>Device View. The Dante Controller - Device View dialog opens. Select your device from the (Select a Dante Device...) drop-down list. NOTES: • If there are multiple NetPA ATs connected to the network that have not been renamed, to identify an individual device you must obtain the MAC address of the desired device from the label on the rear panel.
  • Page 6 NetPA AT Series • Setup Guide (Continued) Click Apply. A warning opens. Click Yes to enter the new name, then close the dialog. The new name is written to the NetPA AT. Repeat as necessary for all NetPA AT devices. NOTE: After the NetPA AT is renamed, it can remain connected to the network. However, subsequent devices must be connected one at a time and renamed before the next device is connected.
  • Page 7 Product Category Step 11 — Dante Operation Select Devices After the receiver inputs of the NetPA AT are configured, they must be routed to the other Dante devices on the audio network. Dante Controller is required. Ensure the control computer and NetPA AT are connected to the same network. From the start menu select All >...
  • Page 8 (receivers). Click the junction again to disconnect the input from the output. See the “Dante Controller” section of the NetPA AT Series user guide for information on Dante Controller operation. Step 12 — Setting the Gain Potentiometer Turn up the gain potentiometer to the desired level. When the pot is set to 0 dB, and a 0 dBFS signal is NetPA 502 AT transmitted through the Dante port, the amplifier outputs full power.

  • Page 9: Creating A Physical Dante Network

    Product Category Creating a Physical Dante Network A physical network is required to share Dante audio channels between a DMP 128 AT device and a NetPA AT. The NetPA 502 AT and NetPA 1001-70V AT have an RJ-45 connector located on the back panel that accepts a standard network cable. A DMP 128-based Dante network can be configured in a star or daisy chain network topology using the four port switch and the Dante Controller in switched mode.

  • Page 10: Front Panel Features

    (Inside India Only) Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +31.33.453.4040 +91.80.3055.3777 +1.714.491.1517 FAX +1.919.850.1001 FAX +31.33.453.4050 FAX +91.80.3055.3737 FAX © 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com...

Table of Contents