Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JEI MAGBEAST HM200T
Summary of Contents for JEI MAGBEAST HM200T
- Page 1 OPERATOR’S MANUAL MAGBEAST HM200T Magnetic Drilling Machine JEI DRILLING & CUTTING SOLUTIONS LTD UNIT 21 EMPIRE BUSINESS PARK, ENTERPRISE WAY, BURNLEY, LANCASHIRE, BB12 6LT, UK TEL: 00 44 1706 229490 E-MAIL: sales@jeisolutions.co.uk Web: www.jeiuk.com...
-
Page 2: Contents Of The Manual
OVERLOAD PROTECTION CIRCUIT & CONNECTION WIRING DIAGRAM [10] GIB ADJUSTMENT -- Patented 13/14/15/ [11] PART LIST 16/17 Check List of Contents with Magbeast HM200T Drilling Machine List Operator's Manual YES/NO Coolant Bottle YES/NO Arbor—MT5 (1 1/4" bore) YES/NO 6mm Hexagon Key... - Page 3 MAGBEAST HM200T MAGBEAST HM200T DRILLING MACHINE [1] SPECIFICATIONS OF Maximum hole cutting capacity in .2/.3C steel = 200mm dia. x 75mm deep Tapping up to M52 Motor Unit Voltages 230v/60Hz 110v/50-60Hz Normal full load output 2850 W Magnet Size 295 x 140 x 70 mm Magnet Force at 20°C with...
- Page 4 MAGBEAST HM200T READ BEFORE USING THE MACHINE [2] SAFETY PROCEDURES ● When using electrical tools, basic safety precautions should always be followed to reduce the risk of electric shock, fire, and personal injury. ● Do NOT use in wet or damp conditions. Failure to do so may result in personal injury.
-
Page 5: Extension Cable Selection
MAGBEAST HM200T [3] OPERATING INSTRUCTIONS Keep the inside of the cutter clear of swarf. It restricts the operating depth of the cutter. ● Ensure that the coolant bottle contains sufficient cutting oil to complete the required operating ● duration. Refill as required. -
Page 6: Mounting Of Cutters
MAGBEAST HM200T lengths shall not be exceeded: For 110v supply: 3.5metres of 3 core x 1.5mm² For 230v supply: 26metres of 3 core x 1.5mm² or 17metres of 3 core x 1.0mm² ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE WHEN CHANGING CUTTERS. -
Page 7: Troubleshooting Guide
MAGBEAST HM200T [6] Trouble Shooting Guide Problem Cause Remedy Magnetic Material being cut may Attach an additional piece of base won’t hold be too thin for efficient metal under work-piece where effectively holding of magnet. magnet will located, mechanically clamp... - Page 8 MAGBEAST HM200T cutter breakage cutter thoroughly and replace Incorrectly re-sharpened Always have a new cutter on or worn cutter hand to refer to for correct tooth geometry, together with instruction sheet Cutter skipping See causes and remedies (2) Slide-ways need...
-
Page 9: Overload Protection
MAGBEAST HM200T [7] SPEED SELECTION—Speed Adjustable with volume switch 1. Method of Gear Change The machines are equipped with a mechanical four-speed gearbox. Please just turn the lever to the right or left to change gear. It is not necessary to set the gear in neutral to change gear.(patented) 2. -
Page 10: Control Panel
MAGBEAST HM200T [9] CONTROL PANEL 10 | P a g e... - Page 11 MAGBEAST HM200T ① MAGNET SWITCH: Main switch of Machine ②SPEED : - HI: GEAR RPM - LO: Electronic RPM, About 75% of HI ③ ROTATION SWITCH - FOR: Forwarding (CW: Clockwise) - REV.: Reverse (CCW: Counter Clockwise) [10] PROTECTION-GEAR SLIP HM200T has a slip system for protection.
-
Page 12: Warning! This Appliance Must Be Earthed
MAGBEAST HM200T [11] CIRCUIT & CONNECTION WIRINGDIAGRAM 1. CIRCUIT WARNING - THIS APPLIANCE MUST BE EARTHED! Insulation Resistance Test With the magnet switch in the ON position, apply a voltage of 1.5kv between the live connection on the mains plug and the frame of the machine for a duration of 7 seconds. -
Page 13: Part List
MAGBEAST HM200T [13] PART LIST PART A 13 | P a g e... - Page 14 MAGBEAST HM200T PART NO. PART NAME Q'ty HM200T SPINDLE HM200T BALL BEARING 6910ZZ HM200T OIL SEAL HM200T MAIN GEAR HM200T BALL BEARING 6906 2RSC3 HM200T SNAP RING HM200T HM200T GEAR BOX HM200T NEEDLE BEARING NK 1012 HM200T FIRST GEAR HM200T...
- Page 15 MAGBEAST HM200T HM200T NEEDLE BEARING RLM1416 HM200T SNAP RING HM200T THIRD GEAR H HM200T THIRD CLUTCH HM200T THIRD PINION HM200T SNAP RING HM200T THIRD GEAR L HM200T SNAP RING HM200T BEARING 16001 ZZ HM200T THIRD CHANGE BLOCK HM200T BEARING 6202 2RSC3...
- Page 16 MAGBEAST HM200T PART B 16 | P a g e...
- Page 17 MAGBEAST HM200T PART NO. PART NAME Q'ty HM200T SLIDE HM200T O-RING ASSEMBLED STOPPER BOLT HM200T PIN PI6-L10 HM200T HEX SOCKET BOLT M6-L15 HM200T ARBOR STOPPER HM200T HEX SOCKET BOLT M5-L10 HM200T WING BOLT M8-L20 HM200T GIB A HM200T RACK GEAR PART NO.
-
Page 18: Warranty Card
MAGBEAST HM200T WARRANTY CARD WARRANTY CARD No.................. in the name of Manufacturer warrants the Magbeast 5 Drilling Machine with Magnetic Base to be free of defects in material and workmanship under normal use for a period of 12 months from date of sale.