1. GENERAL INFORMATION 1.1. Application The Minibeast Cordless is a drilling machine designed to drill holes of diameters up to 36 mm (1.42″) with TCT annular cutters and up to 30 mm (1.18″) with HSS annular cutters. The machine can also drill holes of diameters up to 12 mm (0.47″) by using twist drill bits.
3 units 5 Battery 18 V LiHD 4.0 Ah 1 unit 6 Box 1 unit - Operator’s Manual 1 unit This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Electromagnetic base switch (MAGNET) Chip guard Control panel LED indicator Hole for a safety strap Electromagnetic base Spindle with arbor This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
21. Do not use on surfaces that are rough, not flat, not rigid, or are covered with rust, paint, chips, or dirt. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Page 7
36. Do not allow the battery to be fully discharged. Do not leave the battery in the machine. 37. Store the machine and battery in a safe and dry place. Do not store discharged battery. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Page 8
39. When you transport the battery, familiarize yourself with hazardous goods carriage regulations (UN 3480 and UN 3481). This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Before using the machine, read the description of the following symbols. Wear eye protection Wear ear protection Refer to instruction manual Warning of flammable substances Warning of corrosive substances This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
(4) so that the flat surfaces (5) align with the screws (6). Use the 4 mm hex wrench to tighten the screws. To remove the tool, loosen the screws. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Do not allow coolant to flow into the motor. Do not use pure water as coolant. You can use a mixture of water and drilling oil. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
To check the charge level, press the charge status button. If only one LED on the charge indicator flashes green, charge the battery. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
4.7. Clamping surface requirements The ferromagnetic surface to which the drilling machine is clamped must be at least 6 mm (0.24”) thick. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Page 14
Some types of steel (non-ferromagnetic) do not conduct the magnetic flux, therefore the machine cannot clamp onto them. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
15 minutes the electromagnetic base turns off Red flashes Motor overload or clamping loss Motor stops This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
9. Turn the handles to the left to put the tool above the workpiece. 10. Lower the chip guard to cover the tool. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Remove the cooling system. 6. With gloves on, remove the tool from the arbor. 7. Put the machine in the box. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
5.3. Battery 18 V LiHD 10.0 Ah Part number: AKM-0738-10-00-02-0 5.4. Pressure cooling system Capacity: 2 liters Part number: UKL-0440-16-00-00-0 This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Part number (vacuum pad, supply hose): JEI-VPAD Part number (vacuum pump with safety reservoir): AGR-0541-10-20-00-0 (EU) AGR-0541-10-10-00-0 (UK) Part number (ejector): ZSP-0587-11-00-00-0 This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
David McFadden, Unit 21 Empire Business Park, Burnley, Lancs, BB12 6LT Burnley, 16 May 2022 ___________________________ David McFadden Managing Director This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.
Signature of seller ......................0.03 / 27 May 2022 WE RESERVE THE RIGHT TO MAKE CHANGES IN THIS MANUAL WITHOUT NOTICE This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited.