Related Manuals for JEI AIRBEAST DRILL-AIR50A
Summary of Contents for JEI AIRBEAST DRILL-AIR50A
- Page 1 OPERATOR’S MANUAL AIR DRILLING MACHINE WITH MAGNETIC BASE DRILL-AIR50A, ATEX Unit 21 Empire Bus Park, Enterprise Way, Burnley, UK, BB12 6LT Phone: +44 1706 229490 www.jeiuk.com e-mail: sales@jeisolutions.co.uk...
-
Page 2: Table Of Contents
Contents 1. GENERAL INFORMATION ....................3 1.1. Application ......................... 3 1.2. Technical data......................4 1.3. Equipment included ....................5 1.4. Dimensions ........................ 6 1.5. Design ........................7 2. SAFETY PRECAUTIONS ....................8 3. STARTUP AND OPERATION ..................11 3.1. Installing and removing the arbor or MT2 twist drill bit ..........11 3.2. -
Page 3: General Information
A safety chain protects the machine from falling in case of clamping loss. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 4: Technical Data
Required ambient temperature 0–40°C (32–104°F) Weight 24.5 kg (54 lbs) * always check the clamping of the magnetic base using the indicator This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 5: Equipment Included
2.5 mm hex wrench 1 unit 8 mm combination wrench 1 unit Equipment box 1 unit – Operator’s Manual 1 unit This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 6: Dimensions
DRILL-AIR50A, ATEX 1.4. Dimensions 503 mm (19 51/64″) 285 mm (11 7/32″) This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 7: Design
Arbor Clamping indicator Chip guard Lug for a safety chain Air connection Magnetic base Magnetic base switch (MAGNET ON / OFF) This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 8: Safety Precautions
14. Use the set screws to tighten the annular cutter. Remove wrenches from the work area before you connect the machine to the power source. 15. Do not use tools that are dull or damaged. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. - Page 9 33. If you are not going to use the machine, remove the tool from the holder. Then, remove the machine from the work area and keep it in a safe and dry place. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited.
- Page 10 34. If you are not going to use the machine for an extended period, put anti-corrosion material on the steel parts. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited.
-
Page 11: Startup And Operation
(4). Next, turn the arbor (drill bit) to the right (5) until it snaps into place. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. - Page 12 (1) to align the holes in the spindle and gearbox (2). Put the drift into the hole (3). Next, hold the carrying handle with one hand and hit the drift with a mallet (4). This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited.
-
Page 13: Installing And Removing The Annular Cutter
(3) with the screws (4). Use the 5 mm hex wrench to tighten the screws. To remove the cutter, loosen the screws (4) with the 5 mm hex wrench. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 14: Installing And Removing The Cooling System
(3). Then, attach the hose to the fitting and move the spring to the arbor (5, 6). To remove the bottle, continue in reverse sequence. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 15: Preparing
Some types of steel (non-ferromagnetic) do not conduct magnetic flux so the machine cannot clamp onto them. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. - Page 16 (1, 2) and tighten the screws. CAUTION: Removing the lock is forbidden! Screws for front-rear adjustment (2) Screws for right-left adjustment (1) This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited.
- Page 17 Then ensure that the machine is clamped to the surface by checking the position of clamping indicator. Drilling is allowed only when the clamping indicator matches the marker. Marker ✓ Clamped Unclamped This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited.
- Page 18 The cooling system works by gravity. Thus, in the inverted or horizontal position, use coolants under pressure or in the form of spray or paste. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited.
-
Page 19: Drilling
Turn the handles to the left to put the tool into the workpiece. Keep the machine in the same position until the hole is made. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. - Page 20 MOTOR slider to OFF to turn off the engine. Before you move the machine, set the MAGNET switch to OFF to turn off the base. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited.
-
Page 21: Maintaining The Air Preparation Unit
24 hours, increase the supply of oil and let the motor operate for 2–3 seconds. This will prevent rusting and degrading of the rotor vanes. This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 22: Adjusting The Gibs
Move the motor up and down and adjust the screws (3) so that the travel is smooth. Next, tighten the screws (4) and then tighten the nuts (5). This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 23: Accessories
4. ACCESSORIES 4.1. Air preparation unit Part number (filter, regulator, lubricator): ZST-000021 4.2. Pressure cooling system Capacity: 2 liters. Part number: UKL-0440-16-00-00-0 This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 24: Environmental Protection
This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 25: Declaration Of Conformity
Person authorized to compile the technical file: David McFadden, JEI, Burnley, UK Bunrley, 19 August 2024 ___________________________ David McFadden Managing Director This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited. -
Page 26: Warranty Card
Signature and stamp of the seller .................. 0.02 / 24 September 2024 WE RESERVE THE RIGHT TO MAKE CHANGES IN THIS MANUAL WITHOUT NOTICE This document is protected by copyrights. Copying, using, or distributing without permission of JEI DRILLING & CUTTING is prohibited.
Need help?
Do you have a question about the AIRBEAST DRILL-AIR50A and is the answer not in the manual?
Questions and answers