Table of Contents
Related Manuals for JEI AIRBEAST 40 ATEX
Summary of Contents for JEI AIRBEAST 40 ATEX
- Page 1 OPERATOR’S MANUAL HORIZONTAL AIR DRILLING MACHINE WITH MAGNETIC BASE AIRBEAST 40 ATEX Unit 21 Empire Business Park, Enterprise Way, Burnley BB12 6LT, UK Phone: 00 44 1706 229490 www.jeiuk.com e-mail: sales@jeisolutions.co.uk...
-
Page 2: Table Of Contents
Contents 1. GENERAL INFORMATION ....................3 1.1. Application ......................... 3 1.2. Technical data......................3 1.3. Equipment included ....................4 1.4. Dimensions ........................ 4 1.5. Design ........................5 2. SAFETY PRECAUTIONS ....................6 3. SYMBOLS ......................... 7 4. STARTUP AND OPERATION ................... 8 4.1. -
Page 3: General Information
1. GENERAL INFORMATION 1.1. Application The AIRBEAST 40 ATEX is a drilling machine designed to drill holes of diameters of up to 40 mm (1 37/64″) to a depth of up to 25 mm (63/64″) by using annular cutters. The machine is Ex c IIC T6/T4 Gb Ex c IIIB T6/T4 Db certified to allow work in potentially explosive atmospheres. -
Page 4: Equipment Included
Cooling system bottle 0.5 l 1 unit – Operator’s manual 1 unit 1.4. Dimensions 600 mm (23 5/8″) 205 mm (8 5/64″) This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 5: Design
MOTOR slider (ON/OFF) Chip guard Hole for a safety strap Magnetic base Clamping indicator Magnetic base switch (MAGNET ON/OFF) Air connection This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 6: Safety Precautions
19. Use annular cutters without the pilot pin only when you drill incomplete through holes. 20. Do not drill holes whose diameter or depth differ from those specified in the technical data. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 7: Symbols
33. If you are not going to use the machine for an extended period, put anti-corrosion material on the steel parts. 34. SYMBOLS Refer to instruction manual Wear ear protection Wear eye protection This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 8: Startup And Operation
Attach the feed lever (1). To install the lever at the other side of the machine, use the 4 mm hex wrench and loosen the head screw (2). Then, attach the head at the other side. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 9: Installing And Removing The Annular Cutter
(6) with the screws (3). Use the 4 mm hex wrench to tighten the screws. To remove the cutter, loosen the screws (3) with the 4 mm hex wrench. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 10: Preparing
(including the supply hose and fittings) are of at least 13 mm (33/64″). Use an air preparation unit that has a filter, regulator, and lubricator. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. - Page 11 Then ensure that the machine is clamped to the surface by checking the position of clamping indicator. Drilling is allowed only when the clamping indicator matches the marker. Marker ✓ Clamped Unclamped This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited.
- Page 12 Do not put the strap into the buckle from the front. Horizontal drilling Vertical drilling CORRECT ✓ INCORRECT The maximum possible twist of the strap Inverted drilling This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited.
- Page 13 Then, turn the feed lever to apply a light pressure on the pilot pin. The coolant should fill the system and start flowing from the cutter. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited.
-
Page 14: Drilling
When the annular cutter goes through the workpiece, the slug core is pushed out with a large force. Slug core This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 15: Maintaining The Air Preparation Unit
24 hours, increase the supply of oil and let the motor operate for 2–3 seconds. This will prevent rusting and degrading of the rotor vanes. This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 16: Accessories
AIRBEAST 40, ATEX 4. ACCESSORIES Air preparation unit Part number (filter, regulator, lubricator): ZST-000021 This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 17: Environmental Protection
This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 18: Declaration Of Conformity
2014/34/EU, 2006/42/EC. Person authorized to compile the technical file: David McFadden, Burnley, UK Burnley, 24 November 2023 ___________________________ David McFadden Managing Director This document is protected by copyrights. Copying, using, or distributing without permission of JEI Drilling & Cutting is prohibited. -
Page 19: Warranty Card
WARRANTY CARD No.................. in the name of Manufacturer warrants the AIRBEAST 40 ATEX Drilling Machine to be free of defects in material and workmanship under normal use for a period of 12 months from the date of sale. This...
Need help?
Do you have a question about the AIRBEAST 40 ATEX and is the answer not in the manual?
Questions and answers