Directed DS3 Installation Manual
For 2022 mitsubishi outlander (smart key)
Hide thumbs
Also See for DS3:
- Installation manual (27 pages) ,
- Installation manual (26 pages) ,
- Installation manual (27 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Directed DS3
Summary of Contents for Directed DS3
- Page 1 933.NISS14 DS3+ / DS4+ v1.04.195.3 2022 Mitsubishi Outlander (Smart Key)
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Pre-Installation Module Programming Test Activating 8-Channel Gateway Wiring diagram Locating components in the vehicle Vehicle connections Module programming For Security-Only and Convenience-Only programming, see next sections. Module programming for convenience only (skip transponder) Pairing remotes Connecting the module 8556T Temperature Sensor... -
Page 3: Introduction
Introduction This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on the DIRECTLINK text in the header for additional information. -
Page 4: Vehicle Function Compatibilities
Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart. Parking Lights Control Remote Start Takeover Arm Factory Security SmartStart Disarm Factory Security... -
Page 5: Pre-Installation And Application Warnings
Pre-installation and application warnings This section highlights important information for this specific firmware and will assist in pricing accordingly, as START HERE well as bringing awareness to any operational or vehicle limitations. Compatibilities and Requirements T-Harness Keys required for Keys required T-Harness is not compatible. -
Page 6: Pre-Installation Module Programming Test
Connect the 12-pin main power harness to the module. DS3+: Wait until the LED turns ON solid red then proceed to the next step. DS4+: The LED turns ON solid blue for 1 second to confirm Bluetooth communication. -
Page 7: Activating 8-Channel Gateway
Activating 8-Channel Gateway Note: If the Pre-Installation Module Programming Test was successful, skip this page and proceed with the full installation. To set the 8-Channel Gateway to Open Mode: 1. Click A new page will appear with a CGW Information tab, and a Restricted Mode tab directly under it. -
Page 8: Wiring Diagram
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( HS CAN Low: Tan: 1 HS CAN High: Tan/Black: 2 HS CAN 2 Low: Orange/Brown: 3 module can also be used for this installation. -
Page 9: Locating Components In The Vehicle
Locating components in the vehicle Optional starter disable connection When using an external relay, use a 1N4002 diode or larger. 1A diode [1N4002+ ] (+) Ignition (-) Ground When Armed (GWA) Output: Blue/White: 2 Refer to the Vehicle connections section for wire and Starter (conn. -
Page 10: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2022 Mitsubishi Outlander (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes. Data harness, 8-pin white connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color... - Page 11 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/19 Blue (-) Trunk Input No Connection H2/20 Green (-) Door Input No Connection H2/21 Gray (-) Hood Switch Input H2/22 Violet/White (AC) Tach Input No Connection Main harness, 12-pin black connector (H3) Module Connects To Conn./Pin...
- Page 12 RF Port harness, 2-pin white connector (H5) Module Conn./Pin Color Description H5/1 RF Loop H5/2 RF Loop D2D harness, 4-pin white (1) and black (2) connectors (H6) Module Conn./Pin Color Description H6/1 Blue (Data) TX H6/2 Black (-) Ground H6/3 Green (Data) RX H6/4...
-
Page 13: Module Programming
DS3+: Connect the 12-pin main power harness to the DS3+ module FIRST. Wait until the LED turns ON solid red before proceeding to the next step. -
Page 14: Module Programming For Convenience Only (Skip Transponder)
Connect the 12-pin main power harness to the module. DS3+ DS4+ DS3+: Wait until the LED turns ON solid red then proceed to the next step. Must connect Solid Solid... -
Page 15: Pairing Remotes
Note: Connected devices become registered within 4 to 6 seconds. 8556T Temperature Sensor The 8556T Temperature Sensor is optional, but included with your DS3+/DS4+ module. When used, the Temperature Sensor must be plugged into the 2-pin black connector of your module. -
Page 16: When Used In Conjunction With Smartstart
Loops Pigtails DO NOT connect the Directed SmartStart ® 2-pin power harness when using the DS3+/DS4+. Power and ground will be provided by the D2D connector on the module. Refer to the Directed SmartStart ® documentation for further details. D2D port configuration Caution! Do not connect the Control Center (antenna) or any digital sensors (8504D) to the white D2D1 port. -
Page 17: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles (EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata, and other such vehicles. -
Page 18: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power. - Page 19 External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
-
Page 20: Soft Reset
If required for your installation, connect all the harnesses to the module, EXCEPT the 12-pin main 12-pin harness power harness. Press and hold the programming button, then connect the 12-pin harness to the module. DS3+: Wait 3 seconds until the LED turns ON solid orange then release the programming button. & &... -
Page 21: Tach Learning Procedure (Not Needed With Virtual Tach)
Tach learning procedure (not needed with Virtual Tach) Data Tach: The procedure is not required as the tach comes preprogrammed. However, it is strongly recommended to learn the exact value of the vehicle for the most consistent and reliable starting and functionality. Hardwired Tach: The procedure is required. -
Page 22: Limited Lifetime Consumer Warranty
Limited Lifetime Consumer Warranty VOXX DEI LLC (the Company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or work- manship within the Lifetime from the date of original purchase in the original vehicle, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor. -
Page 23: Quick Reference Guide (Customer Copy)
3 possible ways you can send commands to your vehicle, using the: in Park (P). • Factory remote. • Aftermarket remote. Press the Remote Start button on the transmitter.* • Directed SmartStart application via your smartphone. & Parking lights The parking lights will flash once to indicate the vehicle is Press... - Page 24 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit www.mysmartstart.com.