Advertisement
S1C17M10
Model
Timers
16-bit PWM timer (T16B)
Supply voltage detector (SVD3)
Detection voltage
Detection level
Other
Serial interfaces
UART (UART2)
Synchronous serial interface (SPIA)
I
2
C (I2C)
*1
Smart card interface (SMCIF)
LCD driver (LCD16A)
LCD output
LCD contrast
Other
Multiplier/divider (COPRO2)
Arithmetic functions
Reset
#RESET pin
Power-on reset
Key entry reset
Watchdog timer reset
Supply voltage detector reset
Interrupt
Non-maskable interrupt
Programmable interrupt
Power supply voltage
V
operating voltage
DD
V
operating voltage for Flash programming 2.4 to 5.5 V (V
DD
Operating temperature
Operating temperature range
Current consumption (Typ. value)
SLEEP mode
*2
HALT mode
RUN mode
Shipping form
1
*3
2
*1 The input filter in I2C (SDA and SCL inputs) does not comply with the standard for removing noise spikes less than 50 ns.
*2 The RAM retains data even in SLEEP mode.
*3 Shown in parentheses is a JEITA package name.
2
1 channel
Event counter/capture function
PWM waveform generation function
Number of PWM output or capture input ports: 2 ports/channel
V
or external voltage (one external voltage input port is provided and an external
DD
voltage level can be detected even if it exceeds V
V
: 28 levels (1.8 to 5.0 V)/external voltage: 32 levels (1.2 to 5.0 V)
DD
Intermittent operation mode
Generates an interrupt or reset according to the detection level evaluation.
1 channel
Baud-rate generator included, IrDA1.0 supported
Open drain output, signal polarity, and baud rate division ratio are configurable.
1 channel
2 to 16-bit variable data length
The 16-bit timer (T16) can be used for the baud-rate generator in master mode.
1 channel
Baud-rate generator included
1 channel
Baud-rate generator included
88SEG × 1–8COM (max.), 80SEG × 9–16COM (max.)
16 levels
1/4 or 1/5 bias power supply included, external voltage can be applied.
16-bit × 16-bit multiplier
16-bit × 16-bit + 32-bit multiply and accumulation unit
32-bit ÷ 32-bit divider
Reset when the reset pin is set to low.
Reset at power on.
Reset when the P00 to P01/P02/P03 keys are pressed simultaneously (can be enabled/
disabled using a register).
Reset when the watchdog timer overflows (can be enabled/disabled using a register).
Reset when the supply voltage detector detects the set voltage level (can be enabled/
disabled using a register).
4 systems (Reset, address misaligned interrupt, debug, NMI)
External interrupt: 1 system (8 levels)
Internal interrupt: 14 systems (8 levels)
1.8 to 5.5 V
= 7.5 V external power supply is required.)
PP
2.4 to 5.5 V (When V
is generated internally)
PP
-40 to 85 °C
0.16 µA
IOSC = OFF, OSC1 = OFF, OSC3 = OFF
0.6 µA
OSC1 = 32 kHz (crystal oscillator), RTC = ON
4 µA
OSC1 = 32 kHz (crystal oscillator), RTC = ON, CPU = OSC1
145 µA
OSC1 = 32 kHz (crystal oscillator), RTC = ON, OSC3 = 1 MHz (ceramic oscillator),
CPU = OSC3
TQFP15-128PIN (P-TQFP128-1414-0.40, 14 × 14 mm, t = 1.2 mm, 0.4 mm pitch)
Die form (Pad pitch: 80 µm (min.))
Seiko Epson Corporation
S1C17M10
.)
DD
Advertisement
