TPM 156/22 These technical specifications state a row of manufactured sizes and models of smoke extraction dampers - multi SEDM. It is valid for production, designing, ordering, delivery, maintenance and operation. CONTENT I. GENERAL.....................................3 Description....................................3 Design.....................................4 Design with actuating mechanism............................4 Communication and control module MDCM........................9...
TPM 156/22 I. GENERAL Description Smoke extraction dampers - SEDM dampers are designed into an inlet or extract smoke ventilation system. The dampers are designed either to close to provide compartmentalization or to open (for fresh air inlet) or to allow removal of the heat and combustible products from a fire in the affected fire zone/compartment.
The actuator for operating the damper blade is mounted ■ in an insulated cover/box. It is accessible after removing Insulated cover/box Actuating mechanism Design .44, .54 and .65 Page 4 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 5
(BEN 24-ST) with plug Cable 1 m, 6 x 0,75 mm Cable 1 m, 6 x 0,75 mm - auxiliary switch connectors * Only available for 24V and selected damper sizes Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 5...
Page 6
(BEE 24-ST) with plug Cable 1 m, 6 x 0,75 mm Cable 1 m, 6 x 0,75 mm - auxiliary switch connectors * Only available for 24V and selected damper sizes Page 6 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 7
Storage temperature -40°C … +80°C Cable 1 m, 3 x 0,75 mm Connection - drive Cable 1 m, 6 x 0,75 mm - auxiliary switch (BE 24-ST) with plug connectors Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 7...
Page 8
Protection class Degree of protection IP 66 Adjustment time for 95° < 60 s Ambient temperature -40°C … +50°C Storage temperature -40°C … +70°C Cable 1 m, 0,5 mm Connection Page 8 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Damper actuator Comms IN Communications loop cable CAT 3 or equivalent 1.5mm 2 core screened Comms OUT 230mm x 160mm x 62mm deep steel enclosure powder coated red - IP54 Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 9...
B+83 (140*) (106*) SEDM Actuating mechanism Damper blade Access door/ inspection cover Dimensions with actuating mechanism InMax 50.75S. Flange** ** If it is necessary, arbitrary flange could be removed. Page 10 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 11
Values “e” and “f” - with flange Values "a","c","e" and "f", has to be respected when projecting related smoke exhaust ducts. Flange with corner hole Flanges of dampers are 30 mm wide with oval hole. Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 11...
BELIMO BEN 225 x (15 N.m) 47,7 51,4 0,0264 49,0 52,9 0,0295 50,0 54,0 0,0318 52,5 56,8 0,0380 Sizes listed within the maximum/minimum sizes can be manufactured on request. Page 12 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 13
60,8 65,8 0,0714 64,2 69,4 0,0819 67,5 72,9 0,0924 68,3 73,7 0,0945 70,9 76,6 0,1029 72,9 78,8 0,1092 Sizes listed within the maximum/minimum sizes can be manufactured on request. Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 13...
Page 14
0,1470 84,2 91,0 0,1568 87,8 94,8 0,1691 BELIMO BEE 94,6 102,3 0,1936 (25 N.m) 1000 101,7 109,7 0,2181 Sizes listed within the maximum/minimum sizes can be manufactured on request. Page 14 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 15
BELIMO BEN 450 x 58,1 62,9 0,0532 (15 N.m) 60,5 65,4 0,0646 62,0 67,1 0,0722 63,2 68,4 0,0779 Sizes listed within the maximum/minimum sizes can be manufactured on request. Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 15...
Page 16
74,3 80,1 0,1392 78,3 84,5 0,1632 82,4 88,9 0,1872 86,5 93,3 0,2112 87,4 94,1 0,2160 90,6 97,5 0,2352 Sizes listed within the maximum/minimum sizes can be manufactured on request. Page 16 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 17
111,0 0,3127 104,1 111,9 0,3180 107,5 115,5 0,3392 BELIMO BEE 111,8 120,0 0,3657 (25 N.m) 121,6 130,4 0,4187 Sizes listed within the maximum/minimum sizes can be manufactured on request. Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 17...
Page 18
68,8 70,3 0,0725 BELIMO BEN 700 x (15 N.m) 71,0 72,6 0,0882 73,8 75,4 0,1071 75,6 77,2 0,1197 Sizes listed within the maximum/minimum sizes can be manufactured on request. Page 18 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 19
80,6 87,1 0,1666 84,7 91,4 0,1972 89,3 96,2 0,2312 93,8 101,0 0,2652 98,4 105,8 0,2992 99,4 106,8 0,3060 Sizes listed within the maximum/minimum sizes can be manufactured on request. Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 19...
Page 20
128,6 0,4482 126,2 135,1 0,4897 127,2 136,2 0,4980 BELIMO BE (40 N.m) 131,3 140,4 0,5312 136,3 145,7 0,5727 Sizes listed within the maximum/minimum sizes can be manufactured on request. Page 20 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 21
94,0 100,4 0,1062 BELIMO BEN 1250 x 97,0 103,6 0,1357 (15 N.m) 100,1 106,7 0,1652 103,7 110,4 0,2006 Sizes listed within the maximum/minimum sizes can be manufactured on request. Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 21...
Page 22
129,6 139,7 0,4147 (25 N.m) 136,3 146,5 0,4862 142,8 153,4 0,5577 150,7 161,5 0,6292 BELIMO BE (40 N.m) Sizes listed within the maximum/minimum sizes can be manufactured on request. Page 22 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 23
185,6 197,8 0,9792 192,5 205,0 1,0557 214,1 227,1 1,2087 SCHISCHEK InMax 50.75 (75 N.m) 1000 228,0 241,4 1,3617 Sizes listed within the maximum/minimum sizes can be manufactured on request. Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 23...
“CLOSED”. The damper body should not be deformed in and not rub against the body of the damper or duct during the course of installation. operation. Dimensions of installation opening Installation opening Ablative Coated Batt Page 24 SEDM - Smoke extraction damper - multi Version 2022-12-20...
If the wall thickness is the same as tested but is a lower EI value, then a higher EIS classified damper can be used within the wall (e.g wall is 100mm thick and fire resistance EI 60, then an EI 120 S damper can be used and will be classified as EI60S) Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 25...
Fire stop coating thickness 1 mm (e.g. HILTI CFS-CT, PROMASTOP-CC or equivalent) Fixing profile with threaded rod → see pages 33 to 36 Calcium silicate Actuator housing* * Cover of actuating mechanism has to be removable after installation Page 26 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Fire stop coating thickness 1 mm (e.g. HILTI CFS-CT, PROMASTOP-CC or equivalent) Fixing profile with threaded rod → see pages 33 to 36 Calcium silicate Actuator housing* * Cover of actuating mechanism has to be removable after installation Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 27...
Fixing profile HILTI MQ-41 (or MQ-41/3 or equivalent) → see page 36 Calcium silicate Actuator housing* L-holder → see page 37 * Cover of actuating mechanism has to be removable after installation Page 28 SEDM - Smoke extraction damper - multi Version 2022-12-20...
M8 bolt assemply on damper side „B“ (bolt M8x105 mm, 2 pcs large washer M8, nut M8) distance from edge see fig. * Connecting straps, spacer straps, screws, screw connections and Promat glue K84 are not included in the delivery! Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 29...
Page 30
10 M8 bolt assemply on damper side „B“ (bolt M8x105 mm, 2 pcs large washer M8, nut M8) distance from edge see fig. * Connecting straps, spacer straps, screws, screw connections and Promat glue K84 are not included in the delivery! Page 30 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 31
M8, nut M8) distance from edge see fig., span max. 400 mm Connecting straps, spacer straps, screws, screw connections and Promat glue K84 are not included in the delivery! Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 31...
Page 32
= min. 30 mm, max. 400 mm Seal all joints (Overplating strips, Spacing strips ■ with SEDM damper) with Promat glue K84. Examples of anchors to the fire dividing con- ■ struction →...
TPM 156/22 Suspension systems Suspension SEDM installed in vertical duct MULTI EIS 120 Brackets must be mounted on sides, location and symmetry is ■ not a specific requirement but is preferential. The dampers and duct must be suspended separately. ■...
Page 34
TPM 156/22 Suspension SEDM installed in horizontal duct MULTI EIS 120 Brackets must be mounted on sides, location and symmetry is ■ not a specific requirement but is preferential. The dampers and duct must be suspended separately. ■ Duct from BS EN 12101-7 in Steel (insulated or spray coated) ■...
Page 35
Coupling Nut M8 - M20 Anchor Hinge plate - min. thickness 10 mm Concrete screw tested for fire resistance R30-R90, max. Tension up to 0.75 KN (length 35 mm) Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 35...
Page 36
Washer for M8 - M20 Nut M8 - M20 Dimension elements of the suspension system Flange of SEDM ■ acc. to the weight of the damper, → see page 35 Flange of duct Page 36 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 37
TPM 156/22 Fixing SEDM according to size, with L-holder - tested fixing on wall / ceiling FOR: A < 500 B ≥ 500 FOR: A < 500 B < 500 FOR: A ≥ 500 B ≥ 500 From inner edge of the damper to...
Page 38
M8 bolt assemply (bolt min. M8x60 mm, 2 pcs large washer M8, nut M8) or equivalent Anchor → see page 35 Fixing profile with threaded rod → see page 36 Page 38 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 39
TPM 156/22 Fixing SEDM according to size - tested fixing to solid / gypsum or ceiling wall FOR: A < 500 B ≥ 500 FOR: A < 500 B < 500 FOR: A ≥ 500 B ≥ 500 From inner edge of the damper to the center of the holder, on both sides / opposite sides (mirrored) 1 holder to CENTER damper part "A"...
Page 40
TPM 156/22 Fixing SEDM to the solid (ceiling) wall construction with Ablative Coated Batt system * ATTENTION TO THE LOCATION OF THE JOINT ! Screws and nuts must not impede the free rotation of Blades. Solid wall construction SEDM Ablative Coated Batt Fixing element/steel holder for connecting damper to the wall (optional accessories MANDIK, a.s.
Page 41
SEDM Ablative Coated Batt Fixing element/steel holder for connecting damper to the wall (optional accessories MANDIK, a.s. or sheet metal min. thickness 2 mm and min. width 60 mm) Screw UNI 6x60 mm Installation hols The method of mounting must meet the ■...
M8 bolt assemply (bolt M8x20 mm, 2 pcs large washer M8, nut M8) * Ceramic self-adhesive tape (FJ 120 Pyrosil B 170-250 kg/m - Tremco-illbruck) or equivalent Lock washers Page 42 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Page 43
TPM 156/22 Example of connection SEDM damper in steel duct MULTI with insulation ROCKWOOL FIREPRO DuctRock Slab Connect the joints of stone wool plates with ROCKWOOL FIREPRO Glue, secure with nails and welding pins at max. spacings of 250 mm.
Page 44
TPM 156/22 Example installed SEDM damper in fire separating construction and connection to steel duct MULTI Connect the joints of stone wool plates with ROCKWOOL FIREPRO Glue, secure with nails and welding pins at max. spacings of 250 mm. Board joints must be covered using ROCKWOOL black aluminium foil tape. Follow duct supplier's instructions and insulation.
For KMM grille ensure blade overlaps do not strike KMM- spacer duct may be required - not included in delivery. ■ Free area value for KMM is 78%. ■ SEDM with cover grille without flange SEDM with cover grille and with flange Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 45...
[kg/m air density ξ coefficient of local pressure loss for the nominal damper section → see page 47 Determination of pressure loss by using diagram ρ = 1,2 kg/m Page 46 SEDM - Smoke extraction damper - multi Version 2022-12-20...
The actuator cover is made of fire-resistant material (fire protection board). ■ IV. INSPECTION, TESTING The appliance is constructed and preset by the manufacturer, its operation is dependent on proper installation and ■ adjustment. Page 54 SEDM - Smoke extraction damper - multi Version 2022-12-20...
All effective safety standards and directives must be obse- ■ rved during damper assembly. Manual operation ■ Without power supply, the damper can be operated ■ manually and fixed in any required position. Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 55...
Seal up the space around cable with fire resistant mastic (HILTI CFS-S ACR, PROMASTOP) or equivalent. Let the mastic harden. ■ example drilled holes Example of position of holes in the wall of the box, without pre-manufactured slot Page 56 SEDM - Smoke extraction damper - multi Version 2022-12-20...
Seal up the space around cable with fire resistant mastic (HILTI CFS-S ACR, PROMASTOP) or equivalent. ■ Let the mastic harden. ■ Drilling areas for routing the connection cable of modul to the actuator Dimensions of protection box Version 2022-12-20 SEDM - Smoke extraction damper - multi Page 57...
Dampers blades should open and close correctly and operation should be visually inspected and documented prior to handover. Inspection hole detail Spare parts Spare parts are supplied only on basis of an order. ■ Page 58 SEDM - Smoke extraction damper - multi Version 2022-12-20...
P - with flanges design size AxB EXAMPLE: SEDM 180x355 - .44/P - 180x355-damper size, .44-damper design, P-with flanges Dampers design Additional digit with actuating mechanism BEN, BEE, BE, InMax 50.75-S for 230V with actuating mechanism BEN, BEE, BE, InMax 50.75-S for 24V with actuating mechanism BEN (BEE)-SR for 24V .65*...
Page 60
Manufacturer MANDÍK, a. s. • Dobříšská 550 • 267 24 Hostomice • Czech Republic • Tel.: +420 311 706 742 • E-Mail: mandik@mandik.cz Authorized representative MANDIK UK Ltd • 130 Aztec West • Bristol BS32 4UB • United Kingdom • Tel.: +44 117 4526376 • E-Mail: help@mandik.co.uk...