Mandik SEDM Installation Instructions Manual
Multi compartment smoke extraction damper
Hide thumbs
Also See for SEDM:
- Manual (44 pages) ,
- Manual (59 pages) ,
- Technical documentation manual (60 pages)
Related Manuals for Mandik SEDM
Summary of Contents for Mandik SEDM
- Page 1 027/12 VALID FROM: 01.10.2013 INSTALLATION INSTRUCTIONS MULTI COMPARTMENT SMOKE EXTRACTION DAMPER SEDM...
-
Page 2: Table Of Contents
Content General information....................Assembly information....................Installation opening..................Statement of installation................... The Blades Overlaps..................The Flanges....................... Connection Diagrams....................Service, assembly and revisions ................Dimensions........................Material.......................... -
Page 3: General Information
General information Smoke extract dampers - multi are shutters in the smoke exhaust piping systems. The dampers are designed to remove heat and combustible products (e.g. smoke) from fire compartments. The damper blade is controlled by actuating mechanism. The dampers are designed for using in fire compartments that can be connected to the smoke exhaust ducts (tested according to EN 1366-8) or they can be installed in or on the construction of the fire compartment. -
Page 4: Installation Opening
Installation in the solid wall construction of fire compartment. Damper blade is in horizontal position. compartment. Damper blade is in vertical position. Position Damper SEDM Solid wall construction Mineral stone wool, density 140 kg/m Fire protection mastic, thickness 1 mm... - Page 5 Installation in the solid wall construction of fire compartment NOTICE The actuating mechanism cover must be removable after installation. Position Damper SEDM Solid ceiling construction Mineral stone wool, density 140 kg/m Fire protection mastic, thickness 1 mm Cement lime plate, thickness 15 mm, density 870 kg/m Hinges...
- Page 6 Installation on the solid wall (ceiling wall) construction Installation on the solid wall construction of fire compartment Damper blade is in horizontal position. Position Damper SEDM Solid wall construction Ceramic paper Hinges Installation on the solid wall construction of fire compartment. Damper blade is in vertical position.
- Page 7 Installation on the solid ceiling construction of fire compartment - suspension Pozice: Damper SEDM Solid ceiling construction Ceramic paper Hinges Cement lime plate Installation on the solid ceiling construction of fire compartment - mounting from top Position Damper SEDM Solid ceiling construction...
-
Page 8: The Blades Overlaps
Back-to-back air - conditioning piping must be hung or supported so as all load transfer from the back-to-back piping to the damper is absolutely excluded. 7. Flanges Flanges for SEDM NOTICE Flanges for square fire dampers are 30 mm wide with oval hole. -
Page 9: The Flanges
8. Blade overlaps The overlaps of SEDM Ax180 Ax200 Ax225 Ax250 Ax280 Ax300 Ax315 Ax355 Ax400 Ax450 Ax500 The overlaps of SEDM with flange Ax550 Ax560 Ax600 Ax630 Ax650 Ax700 Ax710 Ax750 Ax800 Ax900 Ax1000 NOTICE The blade of dampers without flange exceeds body of fire damper by the values “a” and “c”. - Page 10 Actuating mechanism BELIMO BLE 230 Actuating mechanism BELIMO BE 24-12(-ST) Actuating mechanism BELIMO BE 230-12...
-
Page 11: Service, Assembly And Revisions
Actuating mechanism SCHISCHEK InMax 50.75-S Assembly, service and revisions 1. Assembly, maintenance and damper check can be done only by qualified persons, i.e. “AUTHORIZED PERSONS” that have been trained by the manufacturer. 2. All effective safety standards and directives must be observed during fire damper assembly. 3. -
Page 12: Dimensions
26724 Hostomice Czech Republic Tel.: +420 311 706 706 Fax: +420 311 584 810, 311 584 382 e-mail: mandik@mandik.cz www.mandik.cz All rights reserved by Manufacturer. Changes to the product can be applied. The current product information are available on www.mandik.cz...