ABB PT004165 Operation Manual page 105

Operation Manual / Power2 850-M / High-pressure stage
Tables
Tables
Table 1: Definition of pictograms .............................. 11
Table 2: Personal protective equipment to be worn
at all times ...................................................................... 15
Table 3: Personal protective equipment to be worn
specific to the respective task ................................... 15
Table 4: Operating limits ............................................. 19
Table 5: Recommended replacement intervals ....... 19
Table 6: Further data .................................................... 19
Table 7: Swivel lifting eyes.......................................... 30
Table 8: Transporting the high-pressure stage ..... 30
Table 9: Pre-lubrication time....................................... 33
Table 10: Post-lubrication time .................................. 33
Table 11: Filter mesh width......................................... 34
Table 12: Oil pressure range ....................................... 38
Table 13: Lubricating oil temperature ...................... 39
Table 14: Expected replacement intervals [h]......... 48
Table 15: Maintenance intervals ................................ 50
Table 16: Cleaning parameters Power2 LP .............. 53
Table 17: Cleaning parameters Power2 HP.............. 53
Table 18: Operating point for turbine cleaning...... 56
Table 19: Cleaning parameters HP ............................. 57
Table 20: Cleaning parameters LP ............................. 57
Table 21: Holding time.................................................. 57
Table 22: Surface of the flow channel....................... 58
Table 23: Malfunctions when starting - Delayed
start-up .......................................................................... 59
Table 24: Malfunctions when starting - Vibrations.....
59
Table 25: Malfunctions when starting - Rubbing of
rotating parts................................................................ 59
Table 26: Malfunctions during operation - Lubricat-
ing oil pressure too low............................................... 60
Table 27: Malfunctions during operation - Power2 LP
speed reductions.......................................................... 60
Table 28: Malfunctions during operation - Power2
HP speed reductions ................................................... 60
© Copyright 2022 ABB. All rights reserved.
Table 29: Malfunctions during operation - Power2
LP speed increases........................................................ 60
Table 30: Malfunctions during operation - Power2
HP speed increases ....................................................... 61
Table 31: Malfunctions during operation - Exhaust
gas temperature too high............................................ 61
Table 32: Malfunctions during operation - Charge air
pressure too low ............................................................ 62
Table 33: Malfunctions during operation - Charge air
pressure too high .......................................................... 62
Table 34: Malfunctions during operation - Com-
pressor 1 contamination .............................................. 63
Table 35: Malfunctions during operation - Com-
pressor 2 contamination.............................................. 63
Table 36: Surging of the low-pressure or high-pres-
sure stage........................................................................ 64
Table 37: Malfunctions when stopping - Runout
noises ............................................................................... 65
Table 38: Malfunctions when stopping - Runout
time too short ................................................................ 65
Table 39: Measured speed incorrect.......................... 65
Table 40: Weights of the assemblies......................... 68
Table 41: Axial clearance A ........................................... 76
Table 42: Tightening torque (56017).......................... 77
Table 43: Tightening torque (42099)......................... 79
Table 44: Control dimension X.................................... 80
Table 45: Tightening torque (61090)......................... 81
Table 46: Tightening torque (72002) ......................... 83
Table 47: Tightening torque (72004) ......................... 84
Table 48: Tightening torques...................................... 85
Table 49: Cover plate / gasket.................................... 87
Table 50: Tightening torque (42099)......................... 88
Table 51: Customer spare part set (97070) .............. 92
Table 52............................................................................ 93
Table 53 ........................................................................... 94
Table 54 ........................................................................... 95
Table 55 ........................................................................... 96
Table 56 ........................................................................... 97
HZTL4063_EN Revision F March 2022