Related Manuals for Feider Machines FPG750LED
Summary of Contents for Feider Machines FPG750LED
- Page 1 Drywall Sander FPG750LED ORIGINAL INSTRUCTIONS READ INSTRUCTIONS BEFORE USE THE TOOL...
-
Page 2: Safety Warnings
1. SAFETY WARNINGS General Power Tool Safety Warnings WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool"... - Page 3 power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Page 4 a) This power tool is intended to function as a sander. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. b) Operations such as grinding, wire brushing, polishing or cutting-off are not recommended to be performed with this power tool.
- Page 5 snagged and your hand or arm may be pulled into the spinning accessory. l) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. m) Do not run the power tool while carrying it at your side.
- Page 6 a) Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. 5, Warning symbol WARNING-To reduce the risk of injury, user must read instruction manual.
-
Page 7: Your Product
YOUR PRODUCT a. Description 1. Plastic guard 2. Motor 3. Foldable button 4. Speed adjuster 5. Switch push button 6. Extend handle The striped LED light will help end user to be more visible on dusky sanding condition, will not miss an uneven spot and would help to finish sanding faster. - Page 8 On/off switch for LED light b. Technical data - Voltage supply： 230-240V~ - Power： 750W - Frequency 50Hz - Speed: 1000-2100/min - Protection class: - Disc Diameter： Ø225mm - Weight 4.1 kg - Sound pressure level: Lpa = 83,1 dB(A) ；KpA = 3 dB(A) - Sound power level: Lwa = 94,1 dB(A)；...
- Page 9 OPERATING INSTRUCTIONS The Drywall Sander is designed for sanding walls and ceilings made of drywall or plaster. The Sander provides superior finish and is faster than conventional finishing methods for both new construction and renovation work. Clean-up time is minimized by using vacuum cleaner attached to the Sander.
-
Page 10: Installation
HOW TO HOLD A DRYWALL SANDER The Drywall Sander should be held with both hands on the main tube. The hands may be placed anywhere along the main tube for best application. CAUTION: Keep the hands on the main tube. Do not place the hands in the area around the sanding head. - Page 11 STARTING AND STOPPING THE DRYWALL SANDER Make sure power circuit voltage is the same as shown on the specification plate on the Sander, and that the Sander switch is OFF. Connect Sander to power circuit. The Drywall Sander is equipped with a qualified switch with a lock block. Depress the switch, not loosen your hand, this machine will be “ON”, if press the lock block, machine will be on even your hand leave the switch.
- Page 12 Speed adjuster HANDLE EXTENSION ASSEMBLY Depending on the different grinding positions, the length of the machine can be adjusted between 1100-1800mm. Turn the lock nut counter clockwise to loosen, pull the hose to the correct length and then turn the lock nut clockwise to lock. Locking nut SANDING OF GYPSUM JOINTS The Drywall Sander has a special sanding head: the head can rotate in multiple directions, allowing...
- Page 13 The sander must always be in motion when the abrasive pad is in contact with the working surface. Use a steady, sweeping motion. Stopping the Sander (on the working surface), or moving the sander may cause unacceptable micro scratches and affect the uniformity of the working surface. NOTE: Do not allow the rotating abrasive pad coming in contact with sharp protrusions.
-
Page 14: Maintenance
MAINTENANCE Tools should always be clean, clean up debris and dust. Always change the oil (gearbox, bearings) for proper operation. Always check the power cord, plugs, switches to make sure the tools are faultless. The power tools manufactured by the company undergo a strict quality inspection. If the machine is faulty, please consult the authorized service centre (SWAP) for repair. -
Page 15: Declaration Of Conformity
FEIDER 32, rue Aristide Bergès - ZI 31270 Cugnaux - France States that the designated below machine: Product: Drywall sander Model: FPG750LED Serial number: Developed, designed and manufactured in accordance with the requirements of directives: Machinery Directive 2006/42/EC EMC Directive 2014/30/EC...