Related Manuals for Feider Machines FPEP850LED
Summary of Contents for Feider Machines FPEP850LED
- Page 1 DRYWALL SANDER FPEP850LED ORIGINAL INSTRUCTIONS READ INSTRUCTIONS BEFORE USE THE TOOL...
- Page 2 ear customer Thank you for purchasing this product. Please read all the instructions in this manual carefully before you assemble or use the product. Read all the safety information and instructions, to reduce the risk of injury Make sure, when working with electrical tools, that safety glasses are worn Make sure to wear a protective dust mask! While working with wood or other materials harmful dust particles can be formed.
- Page 3 electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Page 4 different from those intended could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Safety instructions for all operations Safety Warnings Common for Grinding, Sanding, Wire Brushing, Polishing or Abrasive Cutting-Off Operations:...
- Page 5 m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. n) Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
-
Page 6: Technical Specifications
SAFETY RULES FOR DRYWALL SANDER 1. USE A RESPIRATOR. Ventilate work area and/or use a dust collector. Continued and prolonged exposure to high concentrations of airborne dust may affect the respiratory system function. 2. MANINTAIN FIRM FOOTING AND BALANCE. Use appropriate scaffolding. Do not overreach. 3. -
Page 7: Installation
INSTRUCTION PICTURE: SPEED ON/OFF SWITCH ADJUSTER CARBON BRUSH MOTOR DUST BAG PIPE LED SWITCH WARNING While working with this tool, the dust caused can be dangerous to one‘s health: While working with a sander always wear eye protection and a dust mask. Do not work with material containing asbestos. - Page 8 DO NOT USE THE SANDER WITHOUT A PROPER ABRASIVE SANDING PAPER INSTALLED (to prevent severe damage to the work). ABRASIVE PAD REPLACEMENT CAUTION: DISCONNECT SANDER FROM POWER SOURCE. 1). Grasp the abrasive belt and strap support (tighten the plate on the bracket), to prevent rotation. 2).
- Page 9 EMPTYING THE DUST DUST BAG Warning: Only empty the dust bag when the machine is switched” off”. The dust bag has an open seam which is sealed by a plastic slide fastener. IF THE BAG IS 50% FULL OF DUST, PLEASE EMPTY THE DUST BAG TIMELY. ADDITIONAL RING INSTALLED.
- Page 10 When the sanding pad is below the level of plastic cover, pls add the back-up ring, to rise the height of sanding pad. SPEED ADUSTMENT: The sanding speed can be adjusted according to different conditions and sanding quality requirements. The Drywall Sander is equipped with a variable speed control. The speed is adjusted by turning the control knob.
- Page 11 300°LED ensure sanding in darkness. Turn on/off LED by LED switch above the LED. LED SWITCH TO TURN ON/OFF DRYWALL SANDER Make sure power circuit voltage is the same as shown on the specification plate on the Sander, and that the Sander switch is OFF.
-
Page 12: Maintenance
NOTE: Do not allow rotating abrasive pad to contact sharp protrusions. Contact with protruding objects (nails, screws, electrical boxes, etc,), can severely damage the abrasive pad MAINTENANCE Keep tools clean, clean up debris and dust. Often add in lubricating oil and grease (reducer, bearing) to keep the tool flexible operation. Always check the power cable, plug, switch, so that the tools in good condition. - Page 13 Avoid exposing the tool to direct sunlight. Electrical products should not be discarded with household products. According to the European Directive 2012/19/EU on waste electrical and electronic equipment and its implementation into national law, electrical products used must be collected separately and disposed of at collection points provided for this purpose. Talk with your local authorities or dealer for advice on recycling.
-
Page 14: Declaration Of Conformity
FEIDER 32, rue Aristide Bergès - ZI 31270 Cugnaux - France States that the designated below machine: Product: Auto vacuum drywall sander Model: FPEP850LED Serial number: Developed, designed and manufactured in accordance with the requirements of directives: Machine Directive 2006/42/EC...