User And Safety Instructions; User Information; Safety Instructions - inVENTer iV-Compact Installation Instructions Manual

USER AND SAFETY INSTRUCTIONS

1 User and safety instructions
Thank you for purchasing this high-quality product from inVENTer!
This section provides an overview of the basic safety precautions for safe and proper operation
of your ventilation system.
1.1

User information

Safety and warning instructions
The safety and warning instructions in these installation instructions have a uniform structure and
are marked with a symbol on the left side of the instruction.
A signal word in front of the text also indicates the hazard level. If several hazard levels exist, the
highest level safety instruction is always used.
The safety and warning instructions contain the following information:
SIGNAL WORD: Type and origin of the danger. Possible consequences of the danger!
• Measures to avoid the danger.
The signal word indicates the severity of the potential danger unless the preventive measures are
taken:
DANGER means: Imminent danger of serious injury or death.
WARNING means: Possible danger of serious injury or death.
CAUTION means: Direct danger of minor/significant injury.
NOTICE Means: Direct or possible risk of property damage due to an adverse event/state.
If you see these signs, ensure you observe the described measures to prevent possible hazards
and/or damage.
Other symbols used in this documentation
In addition to the safety instructions, the following symbols are used:
i
This symbol indicates practical and useful tips for handling your ventilation system.
Before each step, any additional tools and materials required for the activity are
listed.
Red bar over a graphic: graphic shows the interior wall.
Blue bar over a graphic: graphic shows the exterior wall.
► Action required: This prompts the user to perform a specific action.
Check the results: This requires you to check the results of the action you have

performed.
!
Action focus: To be taken into account in the corresponding assembly step.
4
4 iV-Compact ventilation device | Installation instructions
1.2

Safety instructions

The installation instructions are part of your iV-Compact ventilation device and must be available
at all times (see www.inventer.de/downloads). When handing the system to a third party, the infor-
mation regarding access to the installation instructions must be handed over also.
Before performing any work on the unit/system, read the installation instructions carefully and
observe all notices that refer to the installation process in this section.
Also note the safety instructions that precede the described handling instructions. Non-obser-
vance of safety instructions could result in injury and/or property damage.
Intended use
The ventilation device is used to ventilate living rooms, rooms similar to living rooms and other
areas where people spend time, e.g. living rooms and bedrooms, offices, basements and attics. It
is controlled via an inVENTer system control unit (hereinafter also referred to as the "controller").
General information
• Always observe the relevant standards, regulations and guidelines when installing the equip-
ment / system. In particular also applicable building regulations, fire safety regulations and
accident prevention regulations of the employers' liability insurance association.
• Use the equipment/system exclusively for the applications that are described in this documenta-
tion and only in conjunction with components that are recommended, authorised and described
by inVENTer GmbH in this documentation.
Changes or modifications to the equipment/system are not permitted.
• Your ventilation system is exclusively designed for use in ambient temperatures between -20
and 50°C.
• Trouble-free and safe operation of the equipment/system depends upon proper transportation,
proper storage and installation as well as careful operation and maintenance.
• The ventilation device works according to the principle of cross-ventilation. Interior doors must
not be sealed airtight. Provide suitable air transfer measures to create a room network.
Installation and assembly
• CAUTION: The system may only be installed by qualified personnel.
Before starting work, you should have a project plan showing the number of ventilation devices,
the location of the ventilation devices, the ventilation principle (cross ventilation, single room
ventilation, extract ventilation) and the associated controllers. The exact positioning of the indi-
vidual units and control units must be checked at the installation site and, if necessary, adapted
to the local conditions with the involvement of the responsible planner or user.
The ventilation device is installed in an appropriate place in the upper wall area.
• WARNING: For joint operation with fireplaces, safety measures must be taken to prevent a
negative pressure from developing in the building.
The responsible chimney sweep and/or building planner decides which measures need to be
carried out.
iV-Compact ventilation device | Installation instructions
USER AND SAFETY INSTRUCTIONS
5
5