1. Manuals
  2. Brands
  3. Advantage Engineering Manuals
  4. Service Equipment
  5. TRANS PRO X Series
  6. Operation manual

Advantage Engineering TRANS PRO X Series Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TRANS PRO
SERIES
OPERATIONS MANUAL

Advertisement

Table of Contents
loading

Summary of Contents for Advantage Engineering TRANS PRO X Series

  • Page 1 TRANS PRO SERIES OPERATIONS MANUAL...

  • Page 2: Table Of Contents

    Advantage Engineering® TRANS PRO X-Series™ Table of Contents TABLE OF CONTENTS INTRODUCTION to the TRANS PRO X-SERIES ....2 II. SAFETY INFORMATION ............3 - Section 1.01: Important Safety Notice .........3 - Section 1.02: Important Safety Instructions.........5 III. SYSTEM FEATURES & SPECIFICATIONS .......9 - Section 2.01: Features..............9...

  • Page 3: Introduction To The Trans Pro X-Series

    I. Introduction Advantage Engineering® TRANS PRO X-Series™ I. INTRODUCTION TO THE TRANS PRO X-SERIES Congratulations on the purchase of your TRANS PRO system. The TRANS PRO system is a technologically advanced fluid exchanger that allows convenient, quick, thorough, and accurate automatic transmission fluid (ATF) exchanges.

  • Page 4: Ii. Safety Information

    Advantage Engineering® TRANS PRO X-Series™ II. Safety Information II. SAFETY INFORMATION 1.01 IMPORTANT SAFETY NOTICE For your safety, read this manual thoroughly before operating your TRANS PRO system. Your TRANS PRO system is intended for use by properly trained, skilled professional automotive technicians.
  • Page 5 II. Safety Information Advantage Engineering® TRANS PRO X-Series™ • Safety Symbols A safety symbol, when present, gives a graphical description of the potential hazard, and how to avoid the hazard: Risk of Fire Read Instructions Before Use Risk of Explosion...

  • Page 6: Section 1.02: Important Safety Instructions

    Advantage Engineering® TRANS PRO X-Series™ II. Safety Information 1.02 IMPORTANT SAFETY INSTRUCTIONS DANGER Vehicle gases contain Carbon Monoxide, which is a colorless & odorless lethal gas. • Only run engines in well ventilated areas and avoid breathing exhaust gases. Extended breathing of exhaust gases will cause serious injury or death.
  • Page 7 II. Safety Information Advantage Engineering® TRANS PRO X-Series™ WARNING Transmission systems may maintain residual pressure in lines after the engine has been turned off. • Wear safety glasses, chemical resistant gloves, and protective clothing when connecting and disconnecting lines and adapters.
  • Page 8 Advantage Engineering® TRANS PRO X-Series™ II. Safety Information WARNING Risk of unexpected vehicle movement. • Block drive wheels before starting vehicle’s engine to begin an exchange. • Unless instructed otherwise, set parking brake and put gear selector in park. • Do not leave a running vehicle unattended.
  • Page 9 II. Safety Information Advantage Engineering® TRANS PRO X-Series™ WARNING Risk of injury. • This equipment should be operated by qualified personnel only. • Use this equipment only as described in this manual. • Loop the power cord loosely in its proper location when machine is not in use.

  • Page 10: Iii. System Features & Specifications

    Advantage Engineering® TRANS PRO X-Series™ III. System Features & Specifications III. SYSTEM FEATURES & SPECIFICATIONS 2.01 FEATURES Application • Exchanges automatic transmission fluid (ATF) in most transmission systems • Restores power delivery, helps improve fuel economy, and maximizes transmission service life.

  • Page 11: Section 2.02: Dimensions & Technical Specifications

    III. System Features & Specifications Advantage Engineering® TRANS PRO X-Series™ 2.02 DIMENSIONS & TECHNICAL SPECIFICATIONS Specifications • Eight (8) U.S. gallon tanks for new and used ATF • 8’ external nylon reinforced Hytron hoses • 9” rigid rear wheels • 4” swivel caster with brakes •...

  • Page 12: Section 2.03: Machine Overview

    Advantage Engineering® TRANS PRO X-Series™ III. System Features & Specifications 2.03 MACHINE OVERVIEW TRANS PRO+ adapters shown Dipstick Adapter Control Panel Flow Meters New Fluid Reservoir Rigid 9” Wheels 4” Locking Caster Wheels Operations Manual Manual Printed in the U.S.A. for AEC GROUP INC.

  • Page 13: Section 2.04: Control Panel Overview

    III. System Features & Specifications Advantage Engineering® TRANS PRO X-Series™ 2.04 CONTROL PANEL OVERVIEW TRANS PRO+ panel shown. KEYS NAME/FUNCTION DETAILS NEW FLUID IN Display (3 digits) LED Indicates fluid in (in tenths of a quart) Indicates count in TOTAL COUNT mode...
  • Page 14 Advantage Engineering® TRANS PRO X-Series™ III. System Features & Specifications KEYS NAME/FUNCTION DETAILS ADD (ARROW UP) Button - LED Add volume in 1 quart increments (in CHECK TRANS LEVEL mode, .1 quart increments) SUBTRACT (ARROW DOWN) Button - LED Reduce volume in 1 quart increments (in CHECK TRANS LEVEL mode, .1 quart increments)

  • Page 15: Operating Procedures

    IV. Operating Procedures Advantage Engineering® TRANS PRO X-Series™ IV. OVERVIEW AND OPERATING PROCEDURES 3.01 TOOL USAGE CAUTION • Frequently inspect and clean any tools used, and lubricate all non-sealed ratchet mechanisms with light oil. • The use of any other accessories not specified in this manual may create a hazard.

  • Page 16: Section 3.02: Overview Of Trans Pro Service Modes Of Transmission Fluid Exchange

    Advantage Engineering® TRANS PRO X-Series™ IV. Operating Procedures 3.02 OVERVIEW OF TRANS PRO X-SERIES AUTOMATIC TRANSMISION FLUID EXCHANGING SERVICE MODES The TRANS PRO can perform an ATF exchange, drain the transmission pan, and/or top off ATF levels in vehicles that have a dipstick. A fluid exchange service is possible in the cooler line mode (TRANS PRO+ feature).

  • Page 17: Section 3.03: Dipstick Mode

    IV. Operating Procedures Advantage Engineering® TRANS PRO X-Series™ 3.03 DIPSTICK MODE – OPERATING PRODECURE (used ATF and new ATF are transferred through the transmission’s dipstick to the trans- mission system with this mode) NOTE: Confirm vehicle and transmission are at operating temperature before initiating service! Power up.
  • Page 18 Advantage Engineering® TRANS PRO X-Series™ IV. Operating Procedures With engine off, TRANS PRO pumps back the same volume of new ATF to the transmission’s pan through the transmission dipstick. The cumulative volume of new fluid selected LESS the volume of new ATF pumped to the transmission is shown on the left display.

  • Page 19: Section 3.04: Cooler Only Mode (Trans Pro+ Feature)

    IV. Operating Procedures Advantage Engineering® TRANS PRO X-Series™ 3.04 COOLER ONLY MODE – OPERATING PRODECURE (Used ATF and new ATF are transferred through the cooler lines to the transmission system with this mode NOTE: Confirm vehicle and transmission are at operating temperature before initiating service! Power up.
  • Page 20 Advantage Engineering® TRANS PRO X-Series™ IV. Operating Procedures When conditions are correct (i.e. fluid temperature up to operating temperature and correct gear range selected), ATF circulates through the transmission system when the engine is running. TRANS PRO+ extracts 1 quart used ATF from the cooler line. The TRANS PRO+ then pumps back the same amount (1 quart) of new fluid through the other cooler line.

  • Page 21: Section 3.05: Manual/Top Off Mode

    IV. Operating Procedures Advantage Engineering® TRANS PRO X-Series™ 3.05 MANUAL/TOP OFF MODE – OPERATING PRODECURE (Used ATF and new ATF are transferred through the transmission’s dipstick tube to the transmission system with this mode) This mode is used when the transmission pan needs to be removed (to change gaskets or replace filter).
  • Page 22 Advantage Engineering® TRANS PRO X-Series™ IV. Operating Procedures Pause after the correct volume is selected. The ENTER key LED will light and flash. Depress ENTER to start the transfer of fluid. When the TO TRANS or FROM TRANS function is finished, the CHECK TRANS LEVEL LED will light.

  • Page 23: Section 3.06: Drain Waste Tank Mode

    IV. Operating Procedures Advantage Engineering® TRANS PRO X-Series™ 3.06 DRAIN WASTE TANK – OPERATING PRODECURE (Used ATF is transferred from the internal waste tank of TRANS PRO through the drain adapter to external waste ATF reservoir with this mode) Power up. Connect power cord to 12.0 VDC battery. REFER TO BATTERY VOLTAGE CHART ON PAGE 14.

  • Page 24: Section 3.07: Total Count

    Advantage Engineering® TRANS PRO X-Series™ IV. Operating Procedures 3.07 TOTAL COUNT – OPERATING PRODECURE (Used ATF is transferred from the internal waste tank of TRANS PRO through the drain adapter to an external waste ATF reservoir with this mode) Power up. Connect power cord to 12.0 VDC battery. Connect the positive lead of the equip- ment to the positive lead of the battery first.

  • Page 25: Troubleshooting & Additional Help

    V. Troubleshooting Guide Advantage Engineering® TRANS PRO X-Series™ V. TROUBLESHOOTING GUIDE & ADDITIONAL HELP 4.01 TROUBLESHOOTING GUIDE & ADDITIONAL HELP PROBLEM: Reversed Polarity LED is on and the unit is not operational SOLUTION: Polarity is Reversed on vehicle’s battery connection.
  • Page 26 Advantage Engineering® TRANS PRO X-Series™ V. Troubleshooting Guide • If dipstick tube with nut and 2 piece ferrule, make sure that two piece ferrule has proper orientation and nut is tight. • If dipstick tube with push lock fitting, make sure that tube has a proper seal in the push lock fitting.

  • Page 27: Appendix A - Adapters (Trans Pro+ Feature)

    Advantage Engineering® TRANS PRO X-Series™ Appendix A - Adapters APPENDIX A - ADAPTERS 5.01 ADAPTERS Operations Manual Manual Printed in the U.S.A. for AEC GROUP INC.
  • Page 28 Appendix A - Adapters Advantage Engineering® TRANS PRO X-Series™ 5.01 ADAPTERS (CONTINUED) Operations Manual Manual Printed in the U.S.A. for AEC GROUP INC.

  • Page 29: Appendix B - Replacement Parts

    Advantage Engineering® TRANS PRO X-Series™ Appendix B - Replacement Parts APPENDIX B - REPLACEMENT PARTS 5.02 REPLACEMENT PARTS 3160-68-12-1 2291-84-32-4 3075-12-22-7 Cord/Clamp assy., 12’ Audio Signal Cap, New Tank 5370-04-61-2 5370-05-61-2 2228-09-00-4 External Strainer Bowl TRANS PRO display TRANS PRO+ display...
  • Page 30 Appendix B - Replacement Parts Advantage Engineering® TRANS PRO X-Series™ 5.02 REPLACEMENT PARTS (CONTINUED) 2247-12-04-0 2228-59-14-4 2228-52-12-4 Pump Head External Strainer Housing, assy Internal Strainer Housing, assy 6300-00-21-8 6300-00-75-5 6300-00-42-5 Wand assy. Dipstick tube assy., 75,” Dipstick tube assy., 42,”...
  • Page 31 Advantage Engineering® TRANS PRO X-Series™ Appendix B - Replacement Parts 5.02 REPLACEMENT PARTS (CONTINUED) 6350-01-92-4 2030-33-20-0 2030-33-30-1 Selector Valve assy., Quick disconnect, body Quick disconnect, plug TRANS PRO+ 0901-56-92-2 0901-56-92-1 1631-08-60-1 Pressure Hose assy., 92" Return Hose assy., 92" 8" wheel...
  • Page 32 Appendix B - Replacement Parts Advantage Engineering® TRANS PRO X-Series™ 5.02 REPLACEMENT PARTS (CONTINUED) FLOW METER ASSY (BARB FITTINGS) 3107-54-21-4 PART NO. DESCRIPTION 3107-54-00-4 BODY FLOW METER (TRANS ALL) 1625-40-00-8 MAGNET, CERAMIC ROD M5 X M20 LONG 1628-02-00-4 GEAR FLOW METER...

  • Page 33: Appendix C - Maintenance

    Advantage Engineering® TRANS PRO X-Series™ Appendix C - Maintenance APPENDIX C - MAINTENANCE CAUTION • Frequently inspect and clean any tools used, and lubricate all non-sealed ratchet mechanisms with light oil. • The use of any other accessories not specified in this manual may create a hazard.

  • Page 34: Warranty Information

    Warranty Information Advantage Engineering® TRANS PRO X-Series™ LIMITED ONE (1) YEAR WARRANTY TRANS PRO X-SERIES AEC GROUP INC. warrants only to the original Purchaser that under normal use, care and service, the Equipment (except as otherwise provided herein) shall be free from defects in material and workmanship for one year from the date of original invoice.
  • Page 35 Advantage Engineering® TRANS PRO X-Series™ Notes Operations Manual Manual Printed in the U.S.A. for AEC GROUP INC.
  • Page 36 Notes Advantage Engineering® TRANS PRO X-Series™ Operations Manual Manual Printed in the U.S.A. for AEC GROUP INC.
  • Page 37 Advantage Engineering® TRANS PRO X-Series™ Notes Operations Manual Manual Printed in the U.S.A. for AEC GROUP INC.
  • Page 38 TRANS PRO SERIES www.transpro-x.com AEC GROUP INC. 3600 W. Carriage Drive, Santa Ana, CA 92704 Toll-Free: 877-906-1395 • Phone: 714-444-1395 Fax: 714-444-1396 www.aecgroup.net Printed in the U.S.A. Part No. 7705-40-02-1 03/2009 © Copyright 2006 AEC GROUP INC.

This manual is also suitable for:

Trans pro

Table of Contents