Table of Contents
Advertisement
6-16HS
6 Using the centrifuge
Pos: 98 / 100 Sigma /100 BA Ze ntrifu gen (Sta nda rdm odul e)/0 60 Bet rieb _Spinco ntr ol L+S/ 060 Betri eb= == == === == == == === == == === == == === == == === == = @ 7\m od_ 1306 401 216 820 _68. docx @ 43 541 @ 1 @ 1
6
Using the centrifuge
Pos: 99 / 100 Sigma /100 BA Ze ntrifu gen (Sta nda rdm odul e)/0 60 Bet rieb _Spinco ntr ol L+S/ 060 -00 10 E rste Inbe trie bna hme @ 7\ mod _13 064 012 819 61_6 8.d ocx @ 435 48 @ 222 @ 1
6.1
Initial start-up
DANGER
Pos: 100 /01 0 Univ ersal mod ule/
Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ @ 1
Pos: 101 /10 0 Sigm a/11 0 BA Z entrif uge n (Pr ojekt e)/6 -16S _6- 16HS/06 0 Bet rieb/ 060 -00 20 Eins chalt en 6-1 6HS @ 1 3\mo d_1 342 430 024 073 _68. docx @ 68 761 @ 33 3 @ 4
6.2
Switching the centrifuge on
NOTE
Pos: 102 /01 0 Univ ersal mod ule/
Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ @ 1
Pos: 103 /10 0 Sigm a/10 0 BA Z entrif uge n (St anda rd mod ule)/ 060 Betrie b_Spinc ont rol L +S/06 0-0 020 -00 10 Öffn en u nd Schli eße n d es Deck els - 1 Schloss @ 1 2\mo d_1 336 037 032 225 _68. docx @ 64 305 @ 33 @ 1
6.2.1
Opening and closing the lid
WARNING
Pos: 104 /01 0 Univ ersal mod ule/
Lee rzeile @ 0\ mo d_12 021 162 445 00_ 0.doc x @ 1 14 @ 4 @ 1
Pos: 105 /10 0 Sigm a/10 0 BA Z entrif uge n (St anda rd mod ule)/ 060 Betrie b_Spinc ont rol L +S/06 0-0 020 -00 20 Ein setze n vo n Rot ore n un d Z ube hör -- --- --- -- --- -- --- -- --- --- -- --- - @ 7\m od_ 1306 401 617 740 _68. docx @ 43 569 @ 3 @ 1
6.2.2
Installation of rotors and accessories
Pos: 106 /10 0 Sigm a/10 0 BA Z entrif uge n (St anda rd mod ule)/ 060 Betrie b_Spinc ont rol L +S/06 0-0 020 -00 20- 001 0 Eins etzen des R oto rs @ 7\mo d_1 306 402 032 880 _68. docx @ 43 576 @ 44 @ 1
6.2.2.1
Installation of the rotor
26
•
Before the initial start-up, please ensure that your centrifuge is properly
set up and installed (see chapter 5 - "Set-up and connection").
•
Press the mains power switch.
The display then illuminates. The centrifuge is ready for operation.
As a default setting of the 6-16HS, the petroleum program "ASTM oil" is
stored in the system (see chapter 6.3.2.5 - "Standard menu").
The lid can be opened if the centrifuge is at a standstill and if the lid key is
illuminated.
•
Press the lid key in order to open the lid.
The centrifuge cannot be started if the lid is opened.
•
To close, press with both hands slightly on the lid until the electrical lock
is locked.
Do not place your fingers between the lid and the housing when closing
the lid. Risk of crushing!
•
Open the centrifuge lid by pressing the lid key.
•
Unscrew the rotor tie-down screw from the motor shaft (counter-
clockwise).
•
Lower the rotor with its central bore straight down onto the motor shaft.
•
Tighten the rotor tie-down screw clockwise with the supplied rotor
wrench with 10 Nm. In doing so, hold the rotor at its outer rim.
Version 06/2012, Rev. 1.0 • sb-kue
Translation of the original operating manual
Advertisement
Table of Contents
