Table of Contents
Advertisement
Quick Links
Kanguru DVD Autoloader 200
USER'S MANUAL
FCC COMPLIANCE STATEMENTS
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the Distance between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Advertisement
Table of Contents
Related Manuals for Kanguru DVD Autoloader 200
Summary of Contents for Kanguru DVD Autoloader 200
- Page 1 Kanguru DVD Autoloader 200 USER’S MANUAL FCC COMPLIANCE STATEMENTS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-
Page 2: Customer Service
Machines Corporation. All other brand or product names are trademarks of their respective companies or organizations. Kanguru Solutions will not be held responsible for any illegal use of this product nor any losses incurred while using this product. The user himself is responsible for the copyright laws, and is fully responsible for any illegal actions taken. -
Page 3: Package Contents
DVD-Duplication products and hope that this product meets or exceeds your expectations. Your Kanguru DVD-Duplicator is designed for ease of use! It is ready to begin burning DVDs and CDs straight out of the box! Simply plug it in and follow these instructions and you will be duplicating DVDs within a matter of minutes. -
Page 4: Specifications
Features • 200 piece media hopper • Standalone unit • 8X DVD+/-RW • 48X CD-RW • One touch recording • Automatic detection • 80GB Internal hard drive. • 8MB Buffer • Auto detect Specifications Simultaneous Duplication Write Speeds Media Types Operation Mode Support Formats Power... -
Page 5: Getting Started
Getting Started Front View: Top View:... -
Page 6: Rear View
Rear View: Control Panel: Overview: When you turn on your KanguruDVD-Autoloader 200, it will go through an initialization process to setup the robotic arm, detect the DVD/RW drives, and read the internal hard drive. The detection process will be displayed on the LCD screen. After successful start-up, you will enter Operation Mode. - Page 7 RUN button to perform that function. Loading the Source DVD or CD The Kanguru DVD Autoloader 200 uses an internal 80GB hard drive to store images of your source or master discs. When the duplication process begins the system will read from the data from this hard drive and burn it onto the target discs.
-
Page 8: Operation Instructions
Operation Instructions Please Note: Your Kanguru DVD Autoloader 200 has been pre-configured to work right out of the box. However, you may have to adjust the robotic arm if you are finding that it will not properly load/unload your discs. If you find that you robotic arm needs to be adjusted please refer to the Adjusting the Robotic Arm section of this manual. - Page 9 4. Once the Autoloader 200 has finished reading the source disc it will eject the disc and the LCD will instruct you to press any key (Set or Run) to exit. 5. Press the set button until you return to the COPY function and the LCD will show that you have loaded a source disc onto the hard drive.
-
Page 10: Important Notes
Important Notes 1. If you ever need to stop the robotic arm for any reason, press the Emergency Stop button and the arm will shut down. Refer to the Adjusting the Robotic Arm section to reset the arm. 2. Never load blank discs into Disc Bin #3, as that is only used as an output bin. 3. -
Page 11: Individual Functions
Individual Functions Your KanguruDVD-Duplicator has the following functions: • TEST This function will simulate the duplication process but the writers won’t burn the CD-R/DVD-R media, so at the end, CD-R/DVD-R will still be blank discs. • C OPY The Disc copying function allows for the duplication of original master disc, without media test or verify features. -
Page 12: Setup Mode
SETUP MODE Setup Mode lets you change the way that your KanguruDVD-Duplicator works. Press the SET button continuously for 3 seconds to enter this mode. Once entered, use the SET button to jump between individual settings, and use the RUN button to change on/off status of each setting. There are square blocks after settings;... - Page 13 The default value is: “MX”. • SET AS DEFAULT The Kanguru DVD controller will save all changes of the settings made. If you want to restore the factory setting (default setting) push the “SET” button to select this setting and then push the...
-
Page 14: Check Trk Len
• UPDATE FIRMWARE—N/A DO NOT USE THIS FUNCTION UNLESS INSTRUCTED TO DO SO BY A KANGURU SOLUTIONS TECHNICIAN. • TOTAL DISC COUNT Displays a master record of the total discs duplicated. • CHECK TRK LEN This function is for the controller to read and detect the bad sector location. - Page 15 This is used in Standalone Mode only. • DISABLE SEND OPC [ ] DO NOT enable this function unless instructed by a Kanguru Solutions tech support rep. • AUTOMATIC This function is used to adjust the robotic arm in the event that it’s no longer aligned...
- Page 16 ADJUSTING THE ROBOTIC ARM This section will provide you with detailed instructions on how to calibrate the robotic arm in the event that it’s no long aligned correctly with the DVD/RW drive or Disc Bins. Please follow the instruction carefully. 1.
- Page 17 You can adjust the period the duplicator will wait between duplication sets. • DLY BETWEEN DRVS: You can adjust the period the duplicator will wait to move between drives. • SHORT TRAY [ yes ] DO NOT change this setting unless instructed by a Kanguru technician.
- Page 18 DVD FAQ Q1: Can I directly copy an entertainment title on DVD? A1: NO. Copyrighted material with copy protection cannot be duplicated. Most DVDs have CSS encryption, which scrambles the data when copied. Also entertainment DVDs are pressed and can hold up around 20 GB of data, while DVD-R/RWs only hold up to 4.7GB. DVDs that have been decrypted on a PC can be duplicated.
-
Page 19: Supported Formats
Q6: Can I put adhesive paper label on my DVD-R/RW media? A6: NO, it’s not recommended to put any type of paper label on a DVD-R/RW. Skipping and shuttering may result from applying a paper label on a DVD disc. DVD drives tend to reach higher temperatures than CD drives, which may result in weakening the adhesive. -
Page 20: Helpful Hints
Kanguru Solutions strongly recommends you fully insure the duplicator for shipping. Kanguru Solutions is not responsible for if the package is lost or damaged in transit. We suggest using a shipping company that utilizes a “tracking” feature to verify “proof of delivery.”... -
Page 21: Tech Support
Tech Support If you experience any problems using your Kanguru CD or DVD Duplicator or have any technical questions regarding any of our products, please call our tech support department. Our tech support is free and available Monday thru Friday, 9am to 5pm EST.
Need help?
Do you have a question about the DVD Autoloader 200 and is the answer not in the manual?
Questions and answers