Soyal AR-331-E Manual
  1. Manuals
  2. Brands
  3. Soyal Manuals
  4. IP Access Controllers
  5. AR-331-E
  6. Manual

Soyal AR-331-E Manual

Hide thumbs Also See for AR-331-E:
Table of Contents

Advertisement

Quick Links

Download this manual
SOYAL
ACCESS CONTROL SYSTEM
Contents
1
Product
AR-331-E
AR-331-EF
Installation
Peel off screw hole rubbers and frame rubber from rubber pad
Put screw rubbers on the back side of the mounting plate and pull
the cables from the square hole of the mounting plate.
Put a frame rubber on the frame groove of body
Front Panel & Indicator
Left LED
Descrption
Blue
Arming / Blue LED
Input (Active High)
Yellow LED Input
Yellow
(Active High)
While power on the device,
hands off the touch panel
for 10 sec. to make sure
a successful activation.
2
Terminal Cables
CN1
CN2
CN4
CN5
CN6
Peel
5
off frame
rubber
4
Peel
off
screw
rubber
Right LED
Descrption
Green
Power-on/Stand-by
/OK
Red
Error/Alarm
1
2
3
4
5
6
7
8
9
0
最佳感應區
AR-331-E/EF
3
Tools
Flat Head Cap Philips
Tapping Screw: 4x20
Security Torx: M3x10
Security Torx Wrenches
Connect the terminal cables to the body and attach the body to the
mounting plate.
Assemble the covers with the Allen key and screws (accessories supplied).
Turn on the power and LED will light and beep will sound.
27.5 mm
- 1 -
4
Accessories
5
Rubber Pad
7
Frame
1
6
Rubber
5
3
2
Put on/Take off together
INSTALLATION
55 mm
27.5 mm
14
16.5 mm
(Front View)
V220922
Option
RJ45
TCP/IP
Module
4
Screws
Rubber
30 mm
(Side view)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AR-331-E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Soyal AR-331-E

Summary of Contents for Soyal AR-331-E

  • Page 1 SOYAL AR-331-E/EF V220922 ACCESS CONTROL SYSTEM Contents Product Terminal Cables Tools Accessories Option Flat Head Cap Philips Tapping Screw: 4x20 Security Torx: M3x10 Security Torx Wrenches Rubber Pad RJ45 TCP/IP AR-331-E AR-331-EF Module Installation Frame Rubber Peel off frame rubber...

  • Page 2: Connector Table

    Biometrics Device Access controller Fingerprint V220922 Connector Table Cable: Wire Application Wire Color Description CN11 Yellow Net - TX+ Green Net - TX- TCP/IP Output Net - RX+ Black Net - RX- Cable: Cable: Wire Application Wire Color Description Wire Application Wire Color Description Thick Green RS-485(B-)
  • Page 3 WG Mode / Controller Mode Setting Method ,AR-331-E/EF become WG mode (28 WG Mode Controller Mode 1. AR-331-E/EF can be set up as WG26/WG34/WG64 while the 701ServerSQL Parameter Setting 701ServerSQL Parameter Setting Controller is in WG Mode. These Controller can also be paired with the Controller that has WG input function.
  • Page 4 123456 → 09 876112876112 B. Changing the Node ID of Reader Access programming mode → 00 [NNN= Node ID: 000~254; MMM=AR-331-E/EF Door NO.:1~255; AAA=WG Reader Door NO.:1~255 C.Setting up the control mode (M4/M8) Access programming mode → 04 [N=4/8] User...
  • Page 5 (NN=00~15); HHMMhhmm=Starting time to ending time; 7123456H= 7 days of week + Holiday (F= 0: disable; 1: enable)] [e.g.] AR-331-E/EF(without WG reader), to set second time zone which could be passed only at 9:30am to 4:20pm on Mon, Wed and Fri.

  • Page 6: Arming Mode

    Biometrics Device Access controller Fingerprint V220922 Please refer to below floor chart Floor Multi floors Access programming mode → 21 UUUUU LLLLLLLL [UUUUU=User address G: 8 sets of lift control (Input: 0~7) LLLLLLLL: 8 floors setting (L=0=Disable, L=1=Enable) [e.g.] User address NO. 168 can reach only the 6th and 20th floor: Access programming mode →...

  • Page 7: Restoring Factory Settings

    2. For dual-fingerprint sensor module version, user just can select one of fingerprint sensor for identification and can't put two fingerprints to different sensor at the same time. 3. Extra WG keypad panel is needed for adding card or downloading data connected to PC. 4. Each finger need to be collected 1 times enrolling for AR-331-E/EF. M. The process of FP identification 1.

  • Page 8: Firmware Upgrade

    Biometrics Device Access controller Fingerprint V220922 Firmware Upgrade Get the upgrade software from SOYAL or our distributor and run “UdpUpdater” software Execute the software The software is Login the SOYAL web to downloads Update the firmware [Please login the SOYAL web to download the new ISP Firmware.] 1.
  • Page 9 V220922 ACCESS CONTROL SYSTEM IP Setting Open your Web Browser and input factory default IP address: http://192.168.1.127 If the IP address of AR-331-E/EF has changed We must enter the new IP address. Page menu Monitor the on-line computer IP Setting...
  • Page 10 TTT=Door open waiting time:001~600;default value:15 sec. UUUUU＝user address Add card by presenting UUUUU QQQQQ QQQQQ=Card quantity(00001=Continuously inducting) 0 or 1＝Enable target unit (0=AR-331-E/EF, 1=WG Reader) 0 or 1 Reader additional setting ???=Function default value UUUUU＝user address；G=4 sets of lift control(0~3); Lift control setting: multi-doors...
  • Page 11 SOYAL AR-331-E/EF V220922 ACCESS CONTROL SYSTEM Command List (By WG Keyboard) Function Command Exposition YYMMDDHHMMSS ＝ Year/Month/Day/Hour/Min./Sec. Real time clock setting YYMMDDHHMMSS SSSSS= starting user address; EEEEE= ending user address Anti-pass-back (Enable user) SSSSS EEEEE P=0=Enable; P=1=Disable; P=2=Initial UUUUU＝user address；LL ：Floor number(01~64 floor)
  • Page 12 Biometrics Device Access controller Fingerprint V220922 (Main Controller Parameter Setting) (WG Input Port Parameter Setting) ※Default Value Function Option Value Application Enable Egress Beep Sounds 0: Disable ※1: Enable 0 Networking/Stand-Alone ---- ---- ---- 1 ---- ---- ---- ---- 2 ---- Arm/Disarm Zone(Zone: 62) ※0: Enable 1: Disable...

This manual is also suitable for:

Ar-331-ef

Table of Contents