Stand-Alone Mode ("Auto" & "Sound Active" Modes); Master/Slave Mode ("Auto" & "Sound Active" Modes); Dmx Mode; Dmx Channel Values (7-Channel Mode) - Blizzard Lighting COLORSTORM Quick Start Manual

Stand-Alone Mode (Auto or Sound Active):
Allows a single unit to run to a factory installed programs with various options.
1.) To set the fi xture in auto mode, select
Once confi rmed, select from built in patterns from
2.) To set the program fade time, select
Once confi rmed, select the fade time from
3.) To set the fi xture in Sound Active mode, select
Master/Slave Mode (Auto or Sound Active):
Allows you to link up to 32 units together without a controller.
1.) Use standard DMX cables to daisy chain your units together via the DMX con-
nector on the rear of the units. It may be necessary to use a terminator at the
last fi xture. For more information about terminators, see page 8.
2.) Choose a unit to function as the Master. From the
MAST (see below for readout), then select
which master mode you want. The master unit must be the fi rst unit. Finally,
chain the units together using DMX cable.
3.) Select slave function by selecting
SL 1 mode will cause all slave fi xtures to react the same as the master. SL 2
mode will create a "two light" show, where SL 1 and SL 2 fi xtures compliment
each other in a show while still maintaining master/slave confi guration. This
gives additional fl exibility in running shows in master/slave confi guration.

DMX Mode

Allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer on page #17.
1.) The default mode for the fi xture is DMX, which appears as the adress num-
ber, for instance on the LED Readout.
2.) To set DMX mode after previously using the fi xture in master/slave or stand-
alone mode, select
buttons, select the appropriate DMX address. Hit <ENTER> to confi rm the
channel, then hold down the <MENU> key for approximately 3 seconds to lock
the assignment into the fi xture. After the address is locked into the fi xture, it
will appear on the LED panel.
COLORStorm™ PAR Manual Rev. A
, then .
to
then .
to .
then hit <ENTER>.
menu, Select
ON or OFF depending upon
, then either or
from the menu, then using the <UP> or <DOWN>
Page 13
Copyright (c) 2010 Blizzard Lighting, LLC
DMX Channel Values (7 Channel)
Channel
1
.
2
3
4
5
6
7
COLORStorm™ PAR Manual Rev. A
Channel Value Does...
Red Intensity
000 <-> 255
000 <-> 255 Green Intensity
000 <-> 255 Blue Intensity
000 <-> 255 Dimmer (0-100%)
000 <-> 009 Color Macros
010 <-> 024 No Function
025 <-> 033 (Simply) Red
034 <-> 040 Orange (Crush)
041 <-> 047 Orange Yellow
048 <-> 054 Yello (Oh Yeah)
055 <-> 063 Yellow (Submarine)
064 <-> 070 Green (Day)
071 <-> 078 Green (Onions)
079 <-> 093 Green #3 (River)
094 <-> 101 Green Cyan
102 <-> 111 Cyan
112 <-> 118 Powder Blue
119 <-> 124 Light Blue
125 <-> 132 Royal Blue
133 <-> 140 Blue (Eiffel 65)
141 <-> 147 Blue (Hawaii)
148 <-> 155 Blue (Rondo A La Turk)
156 <-> 163 (Behind) Blue (Eyes)
164 <-> 171 True Blue
172 <-> 179 UV Purple
180 <-> 186 Deep Purple (Highway Star)
187 <-> 195 Deep Purple (Smoke On The Water)
196 <-> 201 Magenta #1
202 <-> 209 Magenta #2
210 <-> 216 Pink (Cadillac)
217 <-> 225 Pink (Houses)
226 <-> 233 Pink (Just Pink, OK?)
234 <-> 240 Red (Barchetta)
241 <-> 248 Red (Light... ROOOOOXXXXXXXXANNNNNNNEEEE)
249 <-> 255 White (Rabbit)
000 <-> 255 Strobe (Slow <-> Fast)
Sound Active
000 <-> 127 No Function
128 <-> 187 Color Snaps
188 <-> 255 Color Fades
Page 14
Copyright (c) 2010 Blizzard Lighting, LLC