Table of Contents
Advertisement
[1] DISPLAY POSITIONS
The calendar, each scale factor, cursor measurement
values, etc. are displayed in the following positions of
the C R T .
C H 2
U N C A L
GND
C H 2
c m
U N C A L
GND
C H 1
[2] DISPLAY FUNCTIONS
1 Calendar/Clock
Displays the calendar and clock values in the order of
Month, Day, Y e a r , O'clock, and Minute.
Month:
J A N , F E B , M A R , A P R , M A Y , J U N , J U L , A U G ,
S E P , O C T , NOV, & D E C
Day:
0 1 to
3 1
Year:
0 0 to 9 9
O'clock: 0 0 to 2 3
Minute: 0 0 to 5 9
The above can be set with A and X - Y of the HORIZON-
T A L MODE s w i t c h e s (§) and the S W E E P TIME/DIV con-
trol knob. (Refer to the adjustment instruction.)
2 Cursor Measurement Mode/Delayed Sweep Mode
Displays the cursor measurement mode depending on
combination of the C U R S O R S and V A R I A B L E control
setting.
A V 1 , AV2, AV3, AV4, AT, MAT, R A T I O , P H A S E
The delayed s w e e p mode is also displayed in the same
position.
Triggered delay:
Continuous delay: D E L A Y
Trigger count:
C O U N T
READOUT DISPLAY
C u r s o r M e a s u r e m e n t M o d e /
D e l a y e d S w e e p M o d e
C a l e n d a r / C l o c k
i
C H 1 S c a l e F a c t o r
ADD
B W L
C H 2
I N V E R T
C H 2 S c a l e F a c t o r
D E L A Y ?
C u r s o r M e a s u r e m e n t V a l u e /
- D e l a y e d S w e e p T i m e /
T r i g g e r C o u n t P r e s e t V a l u e ( C S - 6 0 2 0 o n l y )
A S W E E P T I M E
B S W E E P T I M E
B S w e e p S c a l e F a c t o r
A S w e e p S c a l e F a c t o r
C H 4 S c a l e F a c t o r
C H 3 S c a l e F a c t o r
Fig. 7
3 Cursor Measurement Value/Delayed Sweep Time/Trig-
ger Count Preset Value ( C S - 6 0 2 0 only)
In the cursor measurement, a measured value using t w o
cursors is displayed.
In the MAT measurement, a "1" is displayed before the
cursor measurement value to indicate that the m e a s -
ured value is invalid, when t w o cursors get close to each
other and measurement reaches the limit.
In the delayed s w e e p , delayed s w e e p time is displayed.
In the trigger count,"a counted value is displayed.
4
C H I Scale Factor
Displays the channel-1 vertical axis sensitivity for 1 div.
In the U N C A L condition, a">"
channel-1 vertical axis sensitivity. If channel 1 is
grounded, however, a "
" > " is displayed even in the U N C A L condition.
If the A C - D C s w i t c h is set to A C for channel 1 , a " ~ "
mark is displayed above the unit of the vertical axis s e n -
sitivity.
N O T E : No display is provided unless CH1 or A D D of the
V E R T I C A L M O D E s w i t c h e s ® is selected.
U N C A L
U N C A L
is displayed before the
" mark is displayed but no
17
Advertisement
Table of Contents
