Table Of Contents; Cs) Asl Re Eee Een Aren Ary Me - Kenwood CS-5135 Instruction Manual

SAFETY
Symbol in This Manual
This symbol indicates where applicable cautionary or
other imformation is to be found.
Power Source
This equipment operates from a power source that does not
apply more than 250 V rms between the supply conductors
or between either supply conductor and ground. A protec-
tive ground connection by way of the grounding conductor
in the power cord is essential for safe operation.
Grounding the Product
This equipment is grounded through the grounding conduc-
tor of the power cord. To avoid electrical shock, plug the
power cord into a properly wired receptacle before connec-
ting to the equipment input or output terminals.
Use the Proper Power Cord
Use only the power cord and connector specified for your
product.
Use the Proper Fuse
To avoid fire hazard, use a fuse of the correct type.
Do not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an ex-
plosive atmosphere.
Do not Remove Cover or Panel
To avoid personal injury, do not remove the cover or panel.
Refer servicing to qualified personnel.
Voltage Conversion
If the power source is not applied to your product, contact
your dealer. To avoid electrical shock, do not perform the
voltage conversion.
CONTENTS
CS) asl Re eee een aren ary mE 2
FEATURES isc) ivintdsptnivsiatcnntiannitiaemngenins 3
SPECIFICATIONS .........c.ccssscssesssseseseeseseseesesees 4
A\PRECAUTIONS.........sesscsssssesseeseeseeseseeseeneeses 7
CONTROLS AND INDICATORS ..........:0:se0ee000 9
FRONT PANEL..:.:..:ccescesvescsteccersccscoasesecnsnansesdasass 9
REAR: PANEL i. iiesecieSutictacssinvsccsitesscostvesdescecdsuvasies 14
DIRECTIONS FOR USE.........sescscesessesesssseeseeees 15
READOUT DISPLAY (CS-5130 Only) ..........ceeeeeeeeee 15
OPERATING INSTRUCTIONS .........ccccccsesseseseees 16
INITIAL STARTING PROCEDURE. ..........scsssssessssesenses 16
[A] OPERATIONS AS A GENERAL-USE OSCILLOSCOPE16
(1) NORMAL SWEEP DISPLAY OPERATION ............ 16
(2) MAGNIFIED SWEEP OPERATION ..........sc.ssssee0 18
(3) ALTERNATE SWEEP OPERATION..............:0:0000 18
(4) X-Y OPERATION .....ccccsssssscsssseesssssscccssseesessesees 19
(5) VIDEO SIGNAL OBSERVATION.............cc0sscces0es 19
(6) SINGLE SWEEP OPERATION...........cscssssesesssseee 20
[B] READOUT OPERATION (CS-5130 Only).......:...0+. 20
APPLICATION 2 21cfecceeeisdvteistalivceacceetacisce 21
PROBE COMPENSATION........:scscesessecsessesseseeeseens 21
TRACE ROTATION COMPENSATION..........0c0c0c0000: 21
1. DC VOLTAGE MEASUREMENTS. ..........00cseeeeeeeees 21
2. MEASUREMENTS OF THE VOLTAGE
BETWEEN TWO POINTS ON A WAVEFORM ..... 22
3. ELIMINATION OF UNDESIRED SIGNAL
COMPONENTS .0...c.cssescssesssesesssesstesesseeseesses 23
4. VOLTAGE RATIO MEASUREMENT
USING CURSORS...0....cccssesscesecseesssessesseesseesees 23
5. TIME MEASUREMENTS ............ccsecsccecccserseecanves 24
6. TIME DIFFERENCE MEASUREMENT .............0-066+ 24
7. PULSE WIDTH MEASUREMENTS ...........0cssseeceeee 25
8. PULSE RISE TIME AND FALL TIME
MEASUREMENT. ...........cccscecceccrecssescenceeenerecs 26
9. PHASE DIFFERENCE MEASUREMENTS ............++ 27
10. TIME RATIO MEASUREMENT USING CURSORS ..28
11. FREQUENCY MEASUREMENTG...........0ccseeeevsers +29
12. RELATIVE MEASUREMENTS .............:ccccseeeceennee 30
13. PULSE JITTER MEASUREMENTS. ..........-ccereeeeeees 31
14, SWEEP MAGNIFICATIONS ...........scsssssssseesseesses 32
15. APPLICATION OF X-Y OPERATION ........c:sesssee0s: 32
A\MAINTENANCE........cscscssceseeeeesceesessesseneeseees 34
ACCESSORIES ........scccscscssssessescesssssssseeseeseaees 35
NOTE: This instruction manual is described for two models
CS-5130 and CS-5135. Refer to item applied to your
product.