Table Of Contents; Ieora Nated - Kenwood CS-5130 Instruction Manual

SAFETY
Symbol in This Manual
This symbol indicates where applicable cautionary or
other imformation is to be found.
Power Source
This equipment operates from a power source that does not
apply more than 250 V rms between the supply conductors
or between either supply conductor and ground. A protec-
tive ground connection by way of the grounding conductor
in the power cord is essential for safe operation.
Grounding the Product
This equipment is grounded through the grounding conduc-
tor of the power cord. To avoid electrical shock, plug the
power cord into a properly wired receptacle before connec-
ting to the equipment input or output terminals.
Use the Proper Power Cord
Use only the power cord and connector specified for your
product.
Use the Proper Fuse
To avoid fire hazard, use a fuse of the correct type.
Do not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an ex-
plosive atmosphere.
Do not Remove Cover or Panel
To avoid personal injury, do not remove the cover or panel.
Refer servicing to qualified personnel.
Voltage Conversion
If the power source is not applied to your product, contact
your dealer. To avoid electrical shock, do not perform the
voltage conversion.
CONTENTS
BAPERY nc cerianins ieora nated 2
FEATURES sec tasccccternicssclsccscacsietonicdacssisioeisatae 3
SPECIFICATIONS .........csscscssessessesessesestssseeenens 4
[\PRECAUTIONS...........cscscssessseseesesesesesceeseees 7
CONTROLS AND INDICATORS ...........0::csc0ese0 9
FRONT 'PANEL 22.0.5 000-cc0cccnccccececceccensesteadescdeveadsasen 9
REAR PANEL ies. sccseicsccceviceessaxcevssesassvassuevivesseauswee 14
DIRECTIONS FOR USE..........ccccssssscsssseseseeseeess 15
READOUT DISPLAY (CS-5130 Only) ...........c.sece000 15
OPERATING INSTRUCTIONS ............csccseseseees 16
INITIAL STARTING PROCEDURE. ............ccccsccsecceovees 16
[A] OPERATIONS AS A GENERAL-USE OSCILLOSCOPE16
(1) NORMAL SWEEP DISPLAY OPERATION ............ 16
(2) MAGNIFIED SWEEP OPERATION ................00.00 18
(3) ALTERNATE SWEEP OPERATION...............22cc008 18
(4) X-Y OPERATION .............c:sccsecsecserececssenenenseseaes 19
(5) VIDEO SIGNAL OBSERVATION..................c2c0eeer 19
(6) SINGLE SWEEP OPERATION..............0sceecsseeceees 20
(B] READOUT OPERATION (CS-5130 Only).............. 20
APPLICATION i.iesctlecidicccacseeislctes thats tees 21
PROBE COMPENSATION. ............:cscsscecsrercereesersece 21
TRACE ROTATION COMPENSATION ................0000 21
1. DC VOLTAGE MEASUREMENTS ..........0..0c0sceceens 21
2. MEASUREMENTS OF THE VOLTAGE
BETWEEN TWO POINTS ON A WAVEFORDM ..... 22
3. ELIMINATION OF UNDESIRED SIGNAL
COMPONENTS. ......cccccccccseucccnurarsrecoum conerevceseas 23
4. VOLTAGE RATIO MEASUREMENT
USING CURSORG.............cccccsscccesensrs creecsveceens 23
5. TIME MEASUREMENTS ..........cccccecsuesin corenscenerse 24
6. TIME DIFFERENCE MEASUREMENT ...... .....cssscee 24
7. PULSE WIDTH MEASUREMENTS .......... cccecsccssene 25
8. PULSE RISE TIME AND FALL TIME
MEASUREMENTG............cccccereeveveeseen aseseeaeseens 26
9. PHASE DIFFERENCE MEASUREMENTS. ............. 27
10. TIME RATIO MEASUREMENT USING C¥RSORS ..28
11. FREQUENCY MEASUREMENTS ............. ascecseees 129
12. RELATIVE MEASUREMENTS ............065 ovcsssereeees 30
13. PULSE JITTER MEASUREMENTS ........., o:ccsceeesees 31
14. SWEEP MAGNIFICATIONS ..........cccccsee, ovcsseeceeees 32
15. APPLICATION OF X-Y OPERATION ......, gvistdeveveve 32
A\MAINTENANCE.........c.ccseccsesecesesecesnae seseececace 34
ACCESSORIES. cies icceondidve, Buea: 35
NOTE: This instruction manual is described fo; two models
CS-5130 and CS-5135. Refer to item ap plied to your
product.