Maximum Controls MAX SUPER ARM 1300 Installation And Owner's Manual page 47

EMX WEL-200
EMX WEL-200
E N E N
r r
O P O P
i t t e i t t e
n s m n s m
T r a T r a
T T
0 0 0 0
L - 2 L - 2
W E W E
OPEN Transmitter OPEN Transmitter
Typically used on SLIDE gates Typically used on SLIDE gates
J P J P
- 2 - 2
1 0 1 0
K
K
r r
p e p e
J u m J u m
Set both jumpers to 10K position Set both jumpers to 10K position
Wire to 10K Inputs Wire to 10K Inputs
OPEN ONLY NC
OPEN ONLY NC
PHOTO CLS NC
PHOTO CLS NC
OPEN/CLS OPEN/CLS NC NC
12VDC OUT 12VDC OUT
GND GND
O O OPEN ONLY O O O O O O O O OPEN ONLY 10K 10K
C C C C C C C C C C CLS ONLY C CLS ONLY C C C C C 10K 10K
OPEN/CLS OPEN/CLS 10K 10K
12VDC OUT 12VDC OUT
GND GND
DSP Arm Controller DSP Arm Controller
C
MAX Super 1300/2300 Arms V1
Rev 08-11-22
MAX Arm/Ultra Arm V1b.4
Rev 06-16-22
monitored WIRELESS
monitored WIRELESS
E E
O S O S
r r
C L C L
i t t e i t t e
n s m n s m
T r a T r a
v e r v e r
c e i c e i
R e R e
R R
0 0 0 0
L - 2 L - 2
li n k li n k
T T
W E W E g e g e
0 0
0 0
E d E d
s s s s
e le e le
L - 2 L - 2
W ir W ir
W E W E
R R
0 0 0 0
L - 2 L - 2
W E W E
CLOSE Transmitter CLOSE Transmitter
Receiver Receiver
WEL-200R WEL-200R
Wireless Edge link Wireless Edge link
J P J P
- 1 - 1
1 0 1 0
K
K
r r
p e p e
J u m J u m
Wire to (NO) of Relay 1 Wire to (NO) of Relay OPEN
Wire to (NO) of Relay CLOSE Wire to (NO) of Relay 2
GND GND
The WEL-200 is a complete wireless solution for interfacing sensing edges to
The WEL-200 is a complete wireless solution for interfacing sensing edges to
gate and door operators, while ensuring compliance with UL325 monitoring
gate and door operators, while ensuring compliance with UL325 monitoring
standards. Each receiver can connect with up to four transmitters with standards. Each receiver can connect with up to four transmitters with
separate relay and pulse outputs for open and close edge functionality. Each separate relay and pulse outputs for open and close edge functionality. Each
transmitter can run for up to two years on two AA lithium batteries. With transmitter can run for up to two years on two AA lithium batteries. With
enhanced diagnostic features, installation and maintenance for the WEL-200 is enhanced diagnostic features, installation and maintenance for the WEL-200 is
easy and reliable. Feedback is provided for all fault modes, including edge
easy and reliable. Feedback is provided for all fault modes, including edge
open, short conditions, low battery and failed transmitters.
open, short conditions, low battery and failed transmitters.
See next page to connect reciver to transmitter.
See next page to connect reciver to transmitter.
10K Resistor Wiring to WEL-200 Wireless 10K Resistor Wiring to WEL-200 Wireless
CH1 CH1
LLD1 LLD1
CH2 CH2
LLD2 LLD2
CH3 CH3
LLD3 LLD3
CH4 CH4
LLD4 LLD4
JP-2 10K
RELAY RELAY
OPEN OPEN
JP1
COM - OUT COM - OUT COM - OUT COM - OUT
PULSE 1 PLS OPEN PULSE 2 PLS CLOSE
12VDC OUT Monitored 12VDC OUT Monitored
Polarity does NOT matter Polarity does NOT matter
RELAY 1 OPEN
CLOSE
RELAY 2
JP-1 10K
RELAY RELAY
CLOSE CLOSE
JP2
NC - COM - NO NC - COM - NO NC - COM - NO NC - COM - NO
RELAY OPEN RELAY 1 RELAY 2 RELAY CLOSE
CONTACTS SHOWN IN ENERGIZED STATE CONTACTS SHOWN IN ENERGIZED STATE
1 2 3 4 1 2 3 4
O O
N N
MODE MODE
POWER POWER
STATUS STATUS
EARTH EARTH
POWER POWER
12 - 24 12 - 24
VDC/VAC VDC/VAC
47 45