Troubleshooting; Obd Port Black Box; Test Photo Close Nc Sensor - Maximum Controls MAX SUPER ARM 1300 Installation And Owner's Manual

These next pages can help troubleshoot problems that might occur after installation is complete.

obd port black box

Download a simple .txt file to troubleshoot gate operator errors and view event history.
1. Plug MAX USB flash drive into OBD port. OBD LED will flash while file is downloading.
Remove flash drive after LED stops flashing (up to 5 minutes to download).
2. Plug flash drive into any computer USB port OR smart phone using a USB phone adapter.
The most recent 8000 events can be viewed. No special software required.
BATTERY
DSP ARM CONTROLLER
BATTERY VOLTAGE
INPUT
ERROR
E 1/2 F
BATTERY
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE
LEAVE
BATTERY BATTERY
CLOSED
TEST
POWER /
SOLAR IN
POWER
ERD SENSITIVITY
14 12 14 12
16
16
MIN MIN
ERD ERD
1 9 1 9
MAX MOTOR MAX MOTOR
MODULE
SENSE OVER SENSE OVER
PORT 3 7 3 7
LOAD LOAD
OPENING CLOSING
OBD PORT
BLACK BOX
MAXIMUM CONTROLS
RESET
OFF
DSP ARM CONTROLLER
1
2
ALARM 3
4
5 PROGRAMMING MOTION CONTROL
ID PLUG
6
ERROR
1
2
ID 3
4
PLUG 5
6
7
OPEN STOP CLOSE
PROGRAM
8
9
10
OFF
ANTI-
PUSH PULL
EXIT PWR
TAILGATE
SOLAR MODE OPEN OPEN
EXIT LOOP
OFF ON
GND
OFF ON
GATE
CENTER LOOP
LOOP PWR CLOSING GATE SPEED
SAFETY LOOP OPERATOR
MIN MIN
FAULTS
MAX MAX
SINGLE DUAL
24VDC OUTPUT
GND MOTOR 1 MOTOR 2
12VDC OUTPUT
GND
test photo cls nc sensor
Troubleshoot
PHOTO CLS NC
1. Press and HOLD the STOP button & then the OPEN button together until beeping is heard, learn mode begins.
NOTE: DO NOT press the OPEN button before the STOP button or learn mode will NOT function.
2. PHOTO CLS NC LED should be ON if an entrapment sensor is detected.
If PHOTO CLS NC LED is NOT on, sensor has a problem.
Possible problems:
• Photocells are out of alignment
• Photocells are wired wrong - N.C. or N.O. depending on which
type of photocells are used
• Sensor is bad
3. Press STOP button again within 5 min. to end learn mode, beeping stops.
NOTE: If STOP button is not pressed within 5 min. learn mode automatically end after 5 min.
MAX Super 1300/2300 Arms V1

troubleshooting

MOTOR 1 [+]
INPUTS [-]
[+]
MOTOR 2
INPUTS [-]
LIMIT 1
MOTOR 1
LIMIT 2
LIMIT 1
MOTOR 2
CLOSE
LIMIT 2 U S
TIMER
A d
LIMIT 1 R e
MIN MAX MOTOR 1
GND
OFF
LIMITS
LIMIT 2
LIMIT 1
MOTOR 2
GND
LIMITS
ON/OFF LIMIT 2
BATTERY
JOG GATE OPEN
COM
GATE CLOSED
GND
OPEN CLOSE
MAG NO
LOCK COM
NC
MAGLOCK
DELAY
OPEN ONLY NC
M A
PHOTO CLS NC
OFF 2.5 sec OPEN / CLS NC
F l a
1.5 sec
12VDC OUT X
GND
s h
OPEN ONLY 10K
UL
ENTRAP
CLS ONLY 10K
D r i
OPEN / CLS 10K
12VDC OUT
GND
entrapment protection sensor (Photocell typically used):
S m
a r t
P h o
n e
n e
h o C o m
B P
p u t
e r
a p t
e r
d
i r e
q u
O R
v e
OPEN ONLY
P P P P PHOTO CLS
OPEN/CLS
12VDC OUT
OPEN ONLY
CLS ONLY
OPEN/CLS
12VDC OUT
Event History Text Document Sample
Event type clarifica�on:
INFO: informa�onal message only
WARNING: unusual event but doesn't cause system malfunc�on
ERROR: abnormal event, could cause system malfunc�on
ENTRAP: entrapment detec�on event
Event Report:
Fri 07/11/2021 10:59:41 INFO : Cycle Counter
Fri 07/11/2021 10:59:41 ENTRAP : SEC_MC: First ERD Detected
Fri 07/11/2021 10:59:37 INFO : Radio Input Deac�vated
Fri 07/11/2021 10:59:36 INFO : Radio Input Ac�vated
Fri 07/11/2021 10:58:54 INFO : PRI_MC: Fully Open Posi�on Learned
Fri 07/11/2021 10:58:53 INFO : SEC_MC: Fully Open Posi�on Learned
Fri 07/11/2021 10:57:40 INFO : PRI_CIO: Communica�on Established
Fri 07/11/2021 10:57:38 ENTRAP : PRI_MC: Photo Cell Deac�vated
Fri 07/11/2021 10:57:34 ENTRAP : PRI_MC: Photo Cell Ac�vated
Fri 07/11/2021 10:57:21 INFO : Radio Input Deac�vated
Fri 07/11/2021 10:57:21 INFO : Radio Input Ac�vated
Fri 07/11/2021 10:56:46 WARNING: PRI_MC: Tamper Reported
Fri 07/11/2021 10:56:36 INFO : SEC_MC: Fully Open Posi�on Unknown
Fri 07/11/2021 10:56:36 INFO : PRI_MC: Fully Open Posi�on Unknown
Fri 07/11/2021 10:56:36 WARNING: PRI_MC: Tamper Reported
Fri 07/11/2021 10:56:33 ENTRAP : PRI_MC: Photo Cell Deac�vated
Fri 07/11/2021 10:56:33 ENTRAP : PRI_MC: Photo Cell Ac�vated
Fri 07/11/2021 10:56:33 ENTRAP : PRI_MC: Photo Cell Deac�vated
Fri 07/11/2021 10:56:33 ENTRAP : PRI_MC: Photo Cell Ac�vated
OPEN STOP
NC
NC
NC
NC
Power
GND
10K
Closing Direction
10K
10K
automatically monitored
GND
MOTION CONTROL
STOP
OPEN CLOSE
MOTION CONTROL
CLOSE
39