Mount Control Box - Maximum Controls MAX SUPER ARM 1300 Installation And Owner's Manual

2

mount control box

Mount the control box as near as possible to the actuator arm. Avoid drilling holes in the side or top of the box.
Seal any holes made in box to keep out moisture.
13.5"
Front
Couplings and conduit
not provided
Bottom
2 1/2"
2 1/2"
3/4" Conduit
Knock-Outs
2 1/2" 4 1/2" 4 1/2"
Use the knock-outs to run desired 3/4" conduit.
Never run low voltage wires in the same conduit
as high voltage wire.
BATTERY
BATTERY VOLTAGE
INPUT
ERROR
E 1/2 F
BATTERY
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE
LEAVE
BATTERY BATTERY
CLOSED
POWER / TEST
SOLAR IN
POWER
ERD SENSITIVITY
14 12 14
16
16
MIN MIN
ERD
9
1 1
MAX MOTOR MAX
MODULE
SENSE OVER SENSE
PORT 3 7 3
LOAD
OPENING CLOSING
OBD PORT
BLACK BOX
MAXIMUM CONTROLS
RESET
OFF
DSP ARM CONTROLLER
1
2
ALARM 3
4
5 PROGRAMMING MOTION CONTROL
ID PLUG
6
ERROR
1
2
3
ID
4
PLUG 5
6
7 OPEN STOP
PROGRAM
8
9
10
OFF
ANTI-
EXIT PWR
SOLAR MODE TAILGATE
EXIT LOOP
OFF ON
GND
OFF ON
CENTER LOOP
LOOP PWR CLOSING GATE SPEED
SAFETY LOOP OPERATOR
MIN
FAULTS
MAX
SINGLE DUAL
24VDC OUTPUT
GND MOTOR 1
12VDC OUTPUT
GND
AVERTISSEMENT: pour ne pas compromettre la
protection contre les risques d'incendie, utiliser un
fusible de mêmes type et caractéristiques nominales.
EXIT CENTER SAFETY
J3 J4 J5
Knock-Outs
Please read all the "SAFETY
PAGES" in front of this manual
(pages 4-11) for installation
requirements and restrictions.
18
4 Mounting Holes
6 1/8"
Mounting hardware
not provided
11"
Mounting Mounting
Hole
10"
Back
Mounting Mounting
1 1/4"
Hole
1"
Use flexible conduit to connect
to control box, not provided.
3"
DSP ARM CONTROLLER
[+]
MOTOR 1
INPUTS [-] Reset Alarm
[+]
MOTOR 2
[-]
INPUTS
Button:
LIMIT 1
MOTOR 1
LIMIT 2
See
LIMIT 1
MOTOR 2
CLOSE
LIMIT 2
TIMER
12 page 33
ERD
9
MOTOR
LIMIT 1
OVER
7
MIN MAX
LOAD MOTOR 1
GND
OFF
LIMITS
LIMIT 2
LIMIT 1
MOTOR 2
GND
LIMITS
LIMIT 2
ON/OFF
BATTERY
JOG GATE OPEN
Toroid Box Connector
COM
GATE CLOSED
GND
OPEN CLOSE
CLOSE MAG NO
LOCK COM
NC
PUSH PULL MAGLOCK
Jog Gate
OPEN OPEN DELAY
OPEN ONLY NC
PHOTO CLS NC
GATE
OFF 2.5 sec OPEN / CLS NC
Open/Close
1.5 sec
12VDC OUT
MIN
GND
See
MAX UL OPEN ONLY 10K
ENTRAP CLS ONLY 10K
MOTOR 2
OPEN / CLS 10K
page 33
12VDC OUT
GND
WARNING: For continued protection
7A
against fire, replace only with the
FUSE
same type and rating of fuse.
On Select Input Voltage
115VAC or 230VAC
Off
POWER
115VAC
POWER IN
3A max
(AC)
1 1/2"
2 1/8"
Operator
Cable
NOTE: Operator
cable should be in
flexible Conduit
(not provided).
5.75"
1 1/4"
RESET ALARM
JOG GATE
OPEN / CLOSE
Hole
17"
Side
Hole
CAREFULLY remove the
delicate control board and
other components before
mounting box. Use the 4
mounting holes to install
box. See components
connections to help with
re-installation.
Battery Plug BATTERY
Red
POWER /
SOLAR IN
Red
Reset
MODULE
Alarm
PORT
RESET
Alarm
ALARM
ID PLUG
ERROR
ID
PLUG
EXIT PWR
EXIT
GND
CENTER
LOOP PWR
SAFETY
White- Exit Pwr
FAULTS
Purple- Exit Loop
24VDC OUTPUT
GND
12VDC OUTPUT
Blue- Gnd
GND
Green- Center Loop
Yellow- Loop Pwr
Safety Loop
Brown-
Black- Faults
EXIT CENTER SAFETY
J3 J4 J5
Loop
Ground
Loop Rack
Flex
Conduit
J-Box
Operator wire
should be in
flexible Conduit,
not provided.
Make sure there is slack in the operator cable.
DO NOT over-bend the operator cable.
Doing this will cause the cable to eventually break.
DO NOT install near sprinklers or any area that
may expose the system to water.
Components Connections
BATTERY
DSP ARM CONTROLLER
BATTERY VOLTAGE
INPUT
ERROR
E 1/2 F
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE
LEAVE
BATTERY BATTERY
CLOSED
TEST
POWER
ERD SENSITIVITY
14 12 14 12
16 16
MIN
MIN
ERD ERD
9 9
1 1
MAX MOTOR MAX MOTOR
SENSE OVER SENSE OVER
3 7 3 7
LOAD LOAD
OPENING CLOSING
OBD PORT
BLACK BOX
MAXIMUM CONTROLS
OFF
DSP ARM CONTROLLER
1
2
3
4
5 MOTION CONTROL
PROGRAMMING
6
1
2
3
4
5
6
7 OPEN STOP CLOSE
PROGRAM
8
9
10
OFF
ANTI-
PUSH PULL
TAILGATE
SOLAR MODE
OPEN OPEN
LOOP
OFF ON
OFF ON
GATE
LOOP
CLOSING GATE SPEED
LOOP OPERATOR
MIN
MIN
MAX MAX
SINGLE DUAL
MOTOR 1 MOTOR 2
Overview of DSP circuit board
on page 52 for reference.
Yellow-
Gray-
Black-
Board
Ground
[ + ]
MOTOR 1
[-]
INPUTS
MOTOR 2 [ + ]
[-]
INPUTS
LIMIT 1
MOTOR 1
LIMIT 2
LIMIT 1
MOTOR 2
CLOSE
LIMIT 2
TIMER
LIMIT 1
MIN MAX MOTOR 1
GND
OFF
LIMITS
LIMIT 2
LIMIT 1
MOTOR 2
GND
LIMITS
LIMIT 2
ON/OFF
BATTERY
JOG
GATE OPEN
COM
GATE CLOSED
GND
OPEN CLOSE
NO
MAG
LOCK
COM
NC
MAGLOCK
DELAY
OPEN ONLY NC
PHOTO CLS NC
OFF 2.5 sec OPEN / CLS NC
1.5 sec
12VDC OUT
GND
OPEN ONLY 10K
UL
ENTRAP
CLS ONLY 10K
OPEN / CLS 10K
12VDC OUT
GND
Jog Open
Jog Close
Gnd
Jog Gate
Open/Close
MAX Super 1300/2300 Arms V1