Copying The Saved Configuration To Nvram - Cisco NPE-175 Installation And Configuration Manual

Copying the Saved Configuration to NVRAM

Compiled Wed 02-Feb-05 04:57 by
ROM: System Bootstrap, Version 12.3(4r)T3, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, 7200 Software (C7200-KBOOT-M),
12.3(20040712:050512) [REL-v123_7_xi_throttle.ios-weekly 115]
Lac1 uptime is 16 hours, 22 minutes
System returned to ROM by reload at 18:12:49 UTC Mon Feb 7 2005
System image file is
"tftp://223.255.254.254/auto/tftpboot-users/biff/c7200-i12s-mz.2005-02-02.BSNOP4_NIGH"
Last reload reason: Reload command
Cisco 7206VXR (NPE-G1) processor (revision 0xFF) with 983040K/65536K bytes of memory.
Processor board ID 31650243
SB-1 CPU at 700MHz, Implementation 1025, Rev 0.2, 512KB L2 Cache
6 slot VXR midplane, Version 2.7
Last reset from power-on
CPU 1 Multi-Processor Forwarding, Tue Feb 1 00:48:42 PST 2005 [rtang 100]
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 400 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 700 bandwidth points.
The set of PA-2FE, PA-POS-2OC3, and I/O-2FE qualify for "half
bandwidth points" consideration, when full bandwidth point counting
results in oversubscription, under the condition that only one of the
two ports is used. With this adjustment, current configuration on bus
mb2 has a total of 700 bandwidth points.
This configuration has oversubscripted the PCI bus and is not a
supported configuration.
Please refer to the following document "Cisco 7200 Series Port
Adaptor Hardware Configuration Guidelines" on CCO <www.cisco.com>,
for c7200 bandwidth points oversubscription/usage guidelines.
WARNING: PCI bus mb2 Exceeds 600 bandwidth points
1 Ethernet interface
2 FastEthernet interfaces
5 Gigabit Ethernet interfaces
1 ATM interface
509K bytes of NVRAM.
62976K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
16384K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2
Copying the Saved Configuration to NVRAM
After installing and cabling the NPE-G1 or NPE-G2 and powering on the router, copy the configuration
file to the NVRAM on the NPE-G1 or NPE-G2, using one of the following procedures:
•
•
•
Network Processing Engine and Network Services Engine Installation and Configuration
7-52
If you have kept the previous I/O controller installed in the router, use the procedure given in the
"Copying the Saved Configuration File from a Flash Disk or PC Card" section on page 7-53
the saved configuration to the NVRAM on the NPE-G1 or NPE-G2.
If you have removed the previously installed I/O controller from the router, and you were able to
copy the file to a CompactFlash Disk, use the procedure given in the
Configuration File from the CompactFlash Disk" section on page 7-53
configuration file to the NVRAM on the NPE-G1 or NPE-G2.
If you have removed the previously installed I/O controller from the router, and you have not been
able to copy the file to a CompactFlash Disk, use the procedure given in the
Configuration from the TFTP Server" section on page 7-54
the NVRAM on the NPE-G1 or NPE-G2.
Chapter 7 NPE-G1 and NPE-G2 Installation and Configuration Information
to copy the saved configuration file to
to copy
"Copying the Saved
to copy the saved
"Downloading the Saved
OL-4448-12