Doosan D50S-5 Operation & Maintenance Manual page 156

Remove the front cover of fuse box. The fuses are Remove the front cover of fuse box. The fuses are
located under the cover. located under the cover.
Fuse - Fuse - Protects an electrical circuit from
an overload. Opens (filament separates) an overload. Opens (filament separates)
if an overload occurs. if an overload occurs.
Typical Example Typical Example
Check the fuses. Use a flashlight, if necessary. Check the fuses. Use a flashlight, if necessary.
Fuses are identified as follows : Fuses are identified as follows :
1. 1. Horn - 10 amp. Horn - 10 amp.
2. 2. Head Lamp - 15 amp Head Lamp - 15 amp
3. 3. Fwd./Rev. Solenoid, lamp Relay & Back-up Fwd./Rev. Solenoid, lamp Relay & Back-up
Lamp/alarm - 10 amp. Lamp/alarm - 10 amp.
4. 4. Instrument Panel & Fuel Shutoff - 15 amp. Instrument Panel & Fuel Shutoff - 15 amp.
5. 5. Turn Signal Lamp, Stop/Strobe Lamp - 15 amp Turn Signal Lamp, Stop/Strobe Lamp - 15 amp
6. 6. Start Relay - 10 amp Start Relay - 10 amp
Maintenance Section Maintenance Section
Bulbs Bulbs
Bulbs are identified as follows Bulbs are identified as follows
[Diesel Engine] [Diesel Engine]
1. 1. Bulb-head lamp halogen(24V-70/75W) Bulb-head lamp halogen(24V-70/75W)
2. 2. Bulb-rear(24V-55W) Bulb-rear(24V-55W)
3. 3. Bulb-turn signal(Front, 24V-25/10W) Bulb-turn signal(Front, 24V-25/10W)
4. 4. Bulb-turn signal(Rear, 24V-25W) Bulb-turn signal(Rear, 24V-25W)
5. 5. Bulb-stop & tail Bulb-stop & tail(24V-25/10W)
6. 6. Bulb-back up(24V-10W) Bulb-back up(24V-10W)
[LP Engine] [LP Engine]
1. 1. Bulb-head lamp halogen(12V-60/55W) Bulb-head lamp halogen(12V-60/55W)
2. 2. Bulb-rear(12V-55W) Bulb-rear(12V-55W)
Protects an electrical circuit from
(24V-25/10W)
Located on top of engine Located on top of engine
Circuit Breaker Circuit Breaker
1. 1. Raise the floor mat. Raise the floor mat.
Typical Example Typical Example
2. 2. The main circuit breaker is located on the rear of The main circuit breaker is located on the rear of
the support for the controls. the support for the controls.
NOTE: NOTE: To reset circuit breakers push on the button. To reset circuit breakers push on the button.
The button should stay in if the breaker is The button should stay in if the breaker is
reset. If the button will not stay in, or comes reset. If the button will not stay in, or comes
out shortly after reset, have the circuits out shortly after reset, have the circuits
checked. checked.
155 155
Check Inflation and Damage Check Inflation and Damage
Inspect tires for wear, cuts, gouges and foreign Inspect tires for wear, cuts, gouges and foreign
objects. Look for bent rims and correct seating of objects. Look for bent rims and correct seating of
locking ring. locking ring.
Check tires for proper inflation. See "Tire Inflation Check tires for proper inflation. See "Tire Inflation
Pressures". Pressures".
To inflate tires always use a clip-on chuck with a To inflate tires always use a clip-on chuck with a
minimum 60 cm (24 inches) length of hose to an minimum 60 cm (24 inches) length of hose to an
inline valve and gauge. inline valve and gauge.
Always stand behind the tread of the tire. NOT in Always stand behind the tread of the tire. NOT in
front of the rim. front of the rim.
LP Engine LP Engine Truck Truck