Table of Contents
Advertisement
6)
Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]
[ON]
f Proceed to Step 7) when [ON] is selected.
7)
Press the <ENTER> button.
f The [QUICK STARTUP] screen is displayed.
8)
Press qw to switch [VALID PERIOD].
f The items will switch each time you press the button.
[30MIN.]
[60MIN.]
[90MIN.]
Note
f When [STANDBY MODE] is set to [NORMAL], the network function can be used during standby.
f When [STANDBY MODE] is set to [NORMAL], the <USB (DC OUT)> terminal can supply power even in standby state. If set to [ECO], the
<USB (DC OUT)> terminal can not supply power in standby state.
f When [STANDBY MODE] is set to [ECO], the network function and the audio output function cannot be used during standby. Also, some
RS-232C commands cannot be used.
f When [STANDBY MODE] is set to [ECO], it takes longer for the projection to start after the power is turned on, compared to when set to
[NORMAL].
f [STANDBY MODE] is fixed to [NORMAL] when the [PROJECTOR SETUP] menu → [SCHEDULE] is set to [ON].
f [QUICK STARTUP] cannot be set when [STANDBY MODE] is set to [ECO].
f When [QUICK STARTUP] is set to [ON], the power consumption during standby becomes high during the period when the [QUICK
STARTUP] function is valid.
f If [QUICK STARTUP] is set to [ON], the [QUICK STARTUP] function is disabled when the time set in [VALID PERIOD] elapses after the
projector enters the standby mode. The startup time and power consumption will be the same as when [QUICK STARTUP] is set to [OFF].
f When [QUICK STARTUP] is set to [ON], the power indicator <ON (G)/STANDBY (R)> blinks red while in the standby mode during the period
when the [QUICK STARTUP] function is valid. When [IN STANDBY MODE] in [AUDIO SETTING] is set to [OFF], the power indicator <ON
(G)/STANDBY (R)> will change to a red light when the specified time set in [VALID PERIOD] elapses after the projector enters the standby
mode.
f When [QUICK STARTUP] is set to [ON], the period when the [QUICK STARTUP] function is valid will be added as the projector runtime.
[BRIGHTNESS CONTROL]
The projector is equipped with a brightness sensor to measure brightness and color of the light source, and
corrects brightness and white balance of the projected image according to the changes in brightness and color of
the light source.
By using this function, in such a condition that multiple screens are configured using multiple projectors, you can
reduce changes in overall brightness and white balance of the multiple screens due to aging of the light source
and suppress variation in brightness and white balance to preserve uniformity.
Set the administrator accounts (user name and password) of all linked projectors to the same setting when
performing brightness control of multiple projectors in synchronization.
Setting [BRIGHTNESS CONTROL SETUP]
Set the operation of the brightness control function.
1)
Press as to select [BRIGHTNESS CONTROL].
2)
Press the <ENTER> button.
f The [BRIGHTNESS CONTROL] screen is displayed.
3)
Press as to select [BRIGHTNESS CONTROL SETUP].
4)
Press the <ENTER> button.
f The [BRIGHTNESS CONTROL SETUP] screen is displayed.
5)
Press as to select [CONSTANT MODE].
Chapter 4 Settings — [PROJECTOR SETUP] menu
Disables the [QUICK STARTUP] function.
Enables the [QUICK STARTUP] function until the specified time set in [VALID PERIOD] elapses after
the projector enters the standby mode. The time until the projection starts after the power is turned on
will be reduced during the period when the [QUICK STARTUP] function is valid.
Sets the time until the [QUICK STARTUP] function is disabled after the projector enters the standby
mode.
Select a desired valid period.
ENGLISH - 109
Advertisement
Table of Contents
