Table of Contents
Advertisement
Quick Links
I N S T A L L A T I O N I N S T R U C T I O N S
Large Flat Panel Dual Arm Wall Mount
Model PNR™
The PNR is wall-mounted, rugged, versatile, and
installer-friendly. The PNR is compatible with the
standard (14" x 14") PSB interface bracket in which a
display can be mounted in either the landscape or
portrait position on the PNR.
The dual arms on the PNR:
Extend from the wall 25" in length
Pivot up to 90º left or right of center
The standard PNR is shipped with the support posts for
the dual arms centered in the mount. The support posts
can be moved laterally right or left of center to readily
accommodate sites with limited wall space. The mount
also has over an inch of height adjustment. The tilt range
for the display is 5º up and 15º down.
The PNR was designed for fast installation. After drawing
the plumb line and installing the two top lag bolts into the
dual wall studs, the installer hangs the PNR on its top
bracket and installs two lag bolts in the bottom bracket.
Next, the installer makes the height adjustment, mounts
the display, and connects the power/audio/video cables,
which are diverted into the built-in path in the swing-out
arms. After making the lateral, rotational, and tilt
adjustments, the installation process is complete.
BEFORE YOU BEGIN
CAUTION: To prevent damage to the PNR, which could affect or void the Factory warranty, and to the equipment that
will be attached to it, thoroughly study all instructions and illustrations before you begin the installation. Pay particular
attention to the "Important Warnings and Cautions" on Page 2.
•
The combined weight of the components installed on the PNR must not exceed 200 lbs. (90.72kg).
•
The PNR wall mount must be installed on dual wall studs or supporting framework. The wall to which the PNR is
anchored must be capable of supporting five times the total weight of the mount and all attached equipment.
•
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.
Chief Manufacturing, a division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
P: 800.582.6480 / 9 52.894.6280 F: 877.894.6 918 / 952.894.6918
8831-000007 Rev I
©2008 Milestone Technologies
11/08
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CHIEF Large Flat Panel Dual Arm Wall Mount PNR
Summary of Contents for CHIEF Large Flat Panel Dual Arm Wall Mount PNR
-
Page 1: Before You Begin
• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480. Chief Manufacturing, a division of Milestone AV Technologies P: 800.582.6480 / 9 52.894.6280 F: 877.894.6 918 / 952.894.6918... -
Page 2: Table Of Contents
Model PNR™ IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. -
Page 3: Dimensional Drawing
Installation Instructions Model PNR™ DIMENSIONAL DRAWING... -
Page 4: Inspect The Unit Before Installing
Model PNR™ Inspect The Unit Before Installing WARNING: Watch for pinch points. Do not put your fingers between movable parts. 1. Carefully inspect the PNR for shipping damage. If any damage is apparent, call your carrier claims agent and do not continue with the installation until the carrier has reviewed the damage. -
Page 5: Installation
Installation Instructions INSTALLATION WARNING: Improper installation can result in serious personal injury! WARNING: It is the responsibility of the installer to verify that the wall to which the PNR is anchored will safely support five times the combined load of all attached components and equipment. -
Page 6: Adjust Height On The Pnr
Model PNR™ Mount (Hang) the PNR on Lag Bolts Figure 2 Use Lag Bolts and Washers to Fasten PNR to the Wall. Figure 3 Adjust Height on the PNR NOTE: Height adjustment range up to 1.08 inches. To adjust the PNR height: 1. -
Page 7: Mount The Display
Installation Instructions Mount the Display 1. Make sure power is not supplied (turned off) to the display before attempting to mount the display. 2. Following the instructions for mounting the PSB interface bracket of your specific plasma display panel, install the mounting bracket on your plasma display panel. -
Page 8: Adjustments
Model PNR™ Management Channel Figure 8 Bottom Cable Management Channel Figure 9 ADJUSTMENTS TENSION ADJUSTMENTS Vertical Tilt Tension Adjustment 1. With display mounted, check for desired vertical tilt tension. Adjust the Centris Select knob until desired vertical tilt tension is obtained. (See figure 10) Installation Instructions Centris Select Adjustment Knob... -
Page 9: Swing Arm Adjustments
Installation Instructions Rotational Tilt Adjustment Nut Figure 12 Swing Arm Adjustments The dual swing arms are shipped installed in the center of the top and bottom mounting brackets, which is the standard mounting configuration. The top and bottom mounting brackets have slotted holes, allowing for lateral adjustment of the dual swing arms. - Page 10 Model PNR™ bottom) and secure using two bolts (one top and one bottom). 5. Install four bolts (two on the top and two on the bottom) to secure the swing arm assembly to the top and bottom mounting brackets (See figure 14). 6.
-
Page 11: Installation Instructions
Installation Instructions Increase Figure 18 Removing Display from Mount Remove bolt or padlock from faceplate (if used). NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes. Pull back on flag on upper mounting hole and press pin down into "Open"... - Page 12 Model PNR™ Installation Instructions...
Need help?
Do you have a question about the Large Flat Panel Dual Arm Wall Mount PNR and is the answer not in the manual?
Questions and answers