Table of Contents
Advertisement
Automatic Editing
Checking the edit points
1
Press the IN (or OUT) button to check the edit
point.
The value of the registered edit point appears on
the display.
2
While holding down the IN (or OUT) button, press
the PREROLL button to check the picture at the
edit point.
The tape is cued up to the edit IN (or OUT) point,
and a still picture of the point appears.
• If "STOP" has been selected as the setup menu
item No.307 (AFTER CUE-UP) setting, the VTR
is set to the E-E mode provided that EE has
been selected as the <HOME> menu
(OUTPUT) setting.
3
By holding down the IN and OUT buttons at the
same time, check the editing duration.
duration appears on the display.
How the duration is calculated
• When two edit points have been set
The duration between the two points is
calculated.
• When only one edit point has been set
The duration between the data which has been
set and the current address is calculated.
• When no edit points have been set
The duration of the previously edited section is
calculated.
POWER
OFF
ON
1
2
3
4
5
6
7
8
CUE
CH
CH CONDITION
MONITOR
FULL/FINE
REMOTE
9P
50P
RS-232C
L
R
HEADPHONES
SHIFT
F1
F2
F3
ABC
DEF
GHI
AUDIO CH SELECT
7
8
9
1
5
2
6
3
7
4
8
PREVIEW/
CH
CH
CH
CH
CH
CH
CH
CH
JKL
MNO
PQRS
REVIEW
4
5
6
BS
AUTO
TUV
WXYZ
EDIT
1
2
3
ENT
PUSH
LOCK
0
C
T
F
REC
P8
REC
P8
REC
P8
REC
P8
FULL
(deck-to-deck)
EJECT
XL/L/M
-cassette
Do not insert S-cassette
without adapter
SHTL
JOG
VAR
ADJUST
HOME
RF1
RF2
ASSEM
PUSH-INTER
VIDEO
UNITY
TC
CUE
INSERT
REV
FWD
AUDIO
UNITY
DIAG
MENU
STAND BY
PLAYER
RECORDER INPUT CHECK
F4
F5
F6
SERVO
REC INHIBIT
EDIT
PLAY
REC
A IN
A OUT
PRE-
ROLL
TRIM
REW
STOP
FF
SET
IN
OUT
2 1, 3
Modifying edit points
1
Re-registering an edit point
Locate the new edit point by performing the jog or
shuttle operation, and press the IN (or OUT) button
and SET button at the same time to re-register the
edit point.
2
Modifying an edit point in 1-frame increments
(trimming function)
Press the TRIM button while holding down the IN
(or OUT) button.
Each time the i button is pressed, the point is
moved ahead by one frame.
Conversely, each time the j button is pressed, the
point is moved back by one frame.
F1
3
Resetting edit points
1 Resetting both an edit IN point and OUT
point
The
Press
(TC CLR = RESET) on the <HOME>
F4
menu.
(This takes effect only in the CTL mode.)
2 Resetting either an edit IN point or OUT point
Press the
while holding down the IN (or OUT) button.
<Notes>
• An edit OUT point can be reset even while
editing is in progress.
• In the eject mode, the IN and OUT points are
automatically reset.
POWER
OFF
ON
1
2
3
4
5
CH
CH CONDITION
MONITOR
FULL/FINE
L
R
HEADPHONES
SHIFT
ABC
FULL
AUDIO CH SELECT
7
1
5
2
6
3
7
4
8
CH
CH
CH
CH
CH
CH
CH
CH
JKL
4
TUV
1
PUSH
LOCK
0
REC
P8
REC
P8
REC
P8
REC
P8
FULL
button among the number keys
C
3
1
XL/L/M
-cassette
Do not insert S-cassette
without adapter
6
7
8
CUE
REMOTE
9P
50P
RS-232C
ADJUST
HOME
RF1
RF2
ASSEM
PUSH-INTER
VIDEO
UNITY
TC
CUE
INSERT
AUDIO
UNITY
DIAG
MENU
STAND BY
PLAYER
RECORDER INPUT CHECK
F1
F2
F3
F4
F5
F6
SERVO
REC INHIBIT
DEF
GHI
EDIT
PLAY
REC
A IN
A OUT
8
9
PREVIEW/
PRE-
MNO
PQRS
REVIEW
ROLL
5
6
BS
AUTO
WXYZ
TRIM
EDIT
REW
STOP
FF
2
3
ENT
SET
IN
OUT
C
T
F
3
2
2
EJECT
SHTL
JOG
VAR
REV
FWD
FULL
1
31
Advertisement
Table of Contents
