Table of Contents
Advertisement
Setup menus
<VIDEO>
No./Item
1
For selecting the video signal which is to be input.
600*
0000
INT SG:
The internal signal selected by the VIDEO INT
VIDEO IN SEL
SG item is generated.
0001
HDSDI:
The serial video signal which has been input to the
HD SDI IN connector is selected.
0002
SDTI: (In 59/60 Hz mode)
The compressed IF signal which has been input to
the SDTI IN connector is selected. (This setting
does not appear when the AJ-YAC15P optional
board has not been installed.)
0002
SD SDI:
The serial video signal which has been input to the
SD SDI IN connector is selected. (This setting does
not appear when the AJ-UC1700G optional board
has not been installed.)
1
For selecting the type of internal signal.
601*
0000 100%CB:
A 100% color bar signal is selected.
VIDEO INT SG
0001 75%CB:
A 75% color bar signal is selected.
0002 SMPTE:
An SMPTE color bar signal is selected.
0003
ARIB:
An ARIB color bar signal is selected.
0004
MB:
A multiburst signal is selected.
0005
RAMP:
A ramp signal is selected.
0006 BLACK:
A black signal is selected.
0007
PLL:
A PLL signal is selected.
0008
EQ:
An EQ signal is selected.
1
For selecting how to process the serial input.
602*
0000 DR OFF: The 8 higher bits after rounding up
SDI IN MODE
0001
DR ON: The signal with 8 higher bits, obtained
603
For selecting whether to mute the video output
signals if LOW RF has been detected during
V-MUTE SEL
playback.
0000 N MUTE:
0001
GRAY:
0002 BLACK:
0003
NOISE:
1
For selecting the freeze mode of the still
604*
pictures and slow playback mode.
0000
FIELD:
FREEZE SEL
0000 FRAME:
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode
has been selected as the system menu item.
*4: This item is not displayed when the 23/24 Hz or 25 Hz (HD) mode has
been selected as the system menu item No.25 (SYSTEM FREQ) setting.
*5: This item is not displayed when the 25 Hz (HD or SD) mode has been
selected as the system menu item No.25 (SYSTEM FREQ) setting.
The underlining (__) denotes the factory setting mode.
Description of setting
the 2 lowest bits are recorded.
by dynamic rounding, is recorded.
The signals are not muted.
(They are frozen.)
The signals are muted with gray.
The signals are muted with black.
The signals are muted with noise.
Field freeze, field slow
Frame freeze, frame slow
No./Item
1
During field slow playback, vertical interpolation is
605*
conducted automatically to minimize the up/down
movement of the playback pictures. However, this
INTERPOLATE
setting enables the interpolation operation to be
forcibly set to OFF.
0000
OFF:
0001
AUTO:
606
For selecting the SD SDI or MONITOR output
signal.
SD MONI O
0000
MONI: : The MONITOR signal is output.
SEL
0001
SDI:
<Note>
When 1 (SDI) is selected, the time code and other
information are not superimposed on the display.
4
For selecting the picture frame during down-
620*
conversion.
0000
FIT_V:
DOWNCON
0001
FIT_H:
MODE
0002 FIT_HV:
0003
14:9:
0004
13:9:
5
For selecting the picture frame during up-
621*
conversion.
0000
FIT_V:
UPCON MODE
0001
FIT_H:
0002 FIT_HV:
622
For selecting the horizontal frequency band
during down-conversion and line conversion
(1080i <> 720p).
D/C RESP
H
0000
WIDE
0001
STD
623
For selecting the vertical frequency band
during down-conversion and line conversion
(1080i <> 720p).
D/C RESP
V
0000
WIDE
0001
STD
5
For selecting the horizontal frequency band
624*
during up-conversion and line conversion.
0000
STD
U/C RESP
0001 NARROW
H
5
For selecting the vertical frequency band
625*
during up-conversion and line conversion.
0000
STD
U/C RESP
0001 NARROW
V
626
For accentuating the horizontal contours
during down-conversion and line conversion
(1080i <> 720p).
D/C ENH
H
0000
0dB
0001
i0.7dB
0002
i1dB
0003 i1. 2dB
0004
i1.5dB
0005
i2dB
Description of setting
The interpolation is forcibly set to OFF.
During slow playback, the interpolation
is automatically set to ON.
The same video signal as the
one output from the SD SDI
OUT1 connector is output
Side cut mode
Letter box mode
Squeeze mode
Semi letter box 14:9
Semi letter box 13:9
Side panel mode
Top and bottom cut in vertical
direction
Stretch mode
<Note>
The numbers on the superimposed
display are approximations only.
93
Advertisement
Table of Contents
