Panasonic AJ-HD1700PE Operating Instructions Manual page 12

Parts and Their Functions
Front panel
L
POWER OFF ON
1 2 3 4 5 6 7 8 CUE
CH
REMOTE
CH CONDITION MONITOR FULL/FINE
9P 50P RS-232C
L R
HEADPHONES
SHIFT F1 F2 F3
ABC DEF GHI
AUDIO CH SELECT
7 8 9
CH 1 CH 5 CH 2 CH 6 CH 3 CH 7 CH 4 CH 8 PREVIEW/
REVIEW
JKL MNO PQRS
4 5 6 BS
TUV WXYZ
1 2 3 ENT
PUSH
LOCK
0 C T F
REC P8 REC P8 REC P8 REC P8
FULL
J K M
J Audio channel selector button
Use this button to select whether the audio controls
for channels CH1 to CH4 or for channels CH5 to
CH8 are to be controlled.
Each time it is pressed, the channel display LED
above the audio control is selected.
K Number keys
Use these keys to input the numerical values of the
CUE points, edit points, etc.
By pressing a number keys from
key is held down, alphabet letters from A to F
F
which are used for the user's bit or letters from A to
Z which are used to compose filenames can be
input.
Since a multiple number of letters are allocated to
each number key, keep tapping the number key
until the desired letter is selected. To change the
input position, use the ADJUST dial, and then
proceed with the input.
L PREVIEW/REVIEW button
PREVIEW: When the button is pressed after an edit
point has been registered, the tape travels and the
editing can be previewed without actually
performing the editing.
If the button is pressed when the IN point has not
been registered, the point where it was pressed is
registered as the IN point, and preview is
executed using this IN point.
REVIEW: When the button is pressed after a
section has been edited, the just edited section is
played back, and it can be reviewed on the
recorder's monitor.
M AUTO EDIT button
When this button is pressed after the edit points
have been registered, automatic editing is initiated.
If the button is pressed when the IN point has not
been registered, automatic editing is initiated with
the point where the button was pressed serving as
the IN point.
12
N
EJECT
XL/L/M -cassette
Do not insert S-cassette
without adapter
ADJUST SHTL JOG VAR
HOME RF1 RF2 ASSEM
PUSH-INTER
VIDEO UNITY TC CUE
INSERT
REV FWD
AUDIO UNITY DIAG MENU
STAND BY PLAYER RECORDER INPUT CHECK
F4 F5 F6
SERVO REC INHIBIT
EDIT PLAY REC
A IN A OUT
PRE-
ROLL
AUTO
TRIM
EDIT REW STOP FF
SET
IN OUT
O
to while the
1 9
N PREROLL button
This button is used to locate where a transmission
or manual editing starts on the tape.
When it is pressed, the tape travels to the preroll
point and it stops there.
When the cue time has been registered on the
HOME, PF1 or PF2 screen:
The tape is prerolled from the registered cue time
using the preroll time which was set using
FULL
(PREROL) on the <HOME SHIFT> menu.
When the search mode is established on the
CUE screen:
The tape is prerolled from the selected cue point
using the preroll time which was set using
(CU-ROL) on the <CUE SHIFT> menu.
The preroll operation is not performed when the
selected cue point has not been registered or
when the cue point registration mode is
established.
In all other situations:
The tape is prerolled from the registered IN point
(or the current tape position when the IN point has
not been registered) using the preroll time which
was set using
SHIFT> menu.
If the PREROLL button is pressed when the IN
point has not been registered, the current tape
position is automatically registered as the IN point
(but only when ENA has been selected as the
setup menu item No.305 (AUTO ENTRY) setting).
When the PREROLL button is pressed together
with the IN (A IN) or OUT (A OUT) button, the tape
can be cued up to the registered point concerned.
To cue up the tape for the cue time registered on
the HOME, PF1 or PF2 screen, press the
PREROLL button while holding down the
among the number keys.
O IN (A IN), SET and OUT (A OUT) buttons
When the IN (A IN) or OUT (A OUT) button is pressed
together with the SET button, the IN (A IN) or OUT (A
OUT) point is registered.The A IN and A OUT buttons
are used to register audio IN and OUT points that
differ from the corresponding video points during
audio split editing.
When an IN (A IN) or OUT (A OUT) point has been
registered, the lamp of the IN (A IN) or OUT (A OUT)
button which has registered that point lights. When
these buttons are pressed after points have been
registered, the IN (A IN) or OUT (A OUT) point value
appears on the counter display.
When the button is pressed while holding down the
C
IN (A IN) or OUT (A OUT) button, the registration of
the IN (A IN) or OUT (A OUT) point is cleared.
[ (PREROL) on the <HOME
F1
.
F1
F5
key
F