Table of Contents
Advertisement
Automatic Editing
Selecting the editing mode
1
Select the editing mode.
ASSEM button:
Assemble (frame-to-frame continuity) editing is
performed in this mode.
INSERT button:
Insert editing is performed in this mode.
2
On the time code display, select the channels to be
edited.
ASSEM:
Set ASSEM to ON using the
INSERT:
To select V, A1, A2, A3, A4 and CUE channels,
press the
to
buttons; to select A5, A6, A7,
F1
F6
A8 and TC channels, press the
+
buttons. The highlighted channels
SHIFT
F6
will now be edited.
3
Press the PLAYER or RECORDER button to select
the VTR which is to be operated.
[Setting for editing using two VTRs]
PLAYER:
Press this button if the player VTR is to be
operated to register the edit points.
RECORDER:
Press this button if the recorder VTR (this VTR) is
to be operated to register the edit points.
[ASSEM screen]
IN point
SHIFT
F1
F2
F3
[INSERT screen]
Marker
IN point
SHIFT
F1
F2
F3
AUDIO IN point
30
(deck-to-deck)
button.
F1
+
to
SHIFT
F2
OUT point
F4
F5
F6
OUT point
F4
F5
F6
AUDIO OUT point
Registering the edit points
1
Locate the edit IN point by performing the jog or
shuttle operation. Set the tape to the still picture
status at the desired position.
For a detailed description of the jog and shuttle
operations, refer to page 27.
2
Press the IN button and SET button together.
The edit IN point is now registered.
The edit IN point value appears on the display.
3
Locate the edit OUT point by performing the jog or
shuttle operation. Set the tape to the still picture
status at the desired position.
4
Press the OUT button and SET button together.
The edit OUT point is now registered.
The edit OUT point value appears on the display.
5
The edit points can be registered directly using the
number keys.
1. Select the <ASSEMBLE> or <INSERT> menu.
2. Press the
button to highlight the edit point. Turn
T
the ADJUST dial to move the highlighting to the IN
point or OUT point.
3. Press the
button again, and input the desired edit
T
point directly using the number keys.
ADJUST dial to move from one digit to the next.
4. Press the
button to register the point.
ENT
To abort the registration at any time, press the
button.
To reset a particular edit point (to 00:00:00:00), press
the
button, align the highlighting with the edit
T
point concerned, and press the
Next, press the
button and
F
Finally, press the
ENT
POWER
OFF
ON
CH
1
2
3
4
5
6
7
8
CUE
CH CONDITION
MONITOR
FULL/FINE
REMOTE
9P
50P
RS-232C
L
R
HEADPHONES
SHIFT
F1
F2
F3
F4
ABC
DEF
GHI
AUDIO CH SELECT
7
8
9
1
5
2
6
3
7
4
8
PREVIEW/
PRE-
CH
CH
CH
CH
CH
CH
CH
CH
JKL
MNO
PQRS
REVIEW
ROLL
4
5
6
BS
AUTO
TUV
WXYZ
EDIT
1
2
3
ENT
PUSH
LOCK
0
C
T
F
REC
P8
REC
P8
REC
P8
REC
P8
FULL
5
Match frame processing function
When two VTRs are used to perform the editing
operations, there will be a total of 4 edit points: the IN
and OUT points for the player and the IN and OUT points
for the recorder. However, the last point is automatically
calculated so only three of the edit points need to be
registered.
Negative duration function
Use setup menu items No.300 (IN/OUT DEL) and
No.301 (NEGA FLASH) in combination.
Turn the
button again.
T
button together.
0
button to register the point.
EJECT
XL/L/M
-cassette
Do not insert S-cassette
without adapter
SHTL
JOG
VAR
ADJUST
HOME
RF1
RF2
ASSEM
PUSH-INTER
VIDEO
UNITY
TC
CUE
INSERT
REV
FWD
AUDIO
UNITY
DIAG
MENU
STAND BY
PLAYER
RECORDER INPUT CHECK
F5
F6
SERVO
REC INHIBIT
EDIT
PLAY
REC
A IN
A OUT
TRIM
REW
STOP
FF
SET
IN
OUT
2, 4
1, 3
C
FULL
Advertisement
Table of Contents
