Table of Contents
Advertisement
Parts and Their Functions
Front panel
>
POWER
OFF
ON
1
2
3
4
5
6
7
8
CUE
CH
CH CONDITION
MONITOR
FULL/FINE
REMOTE
9P
50P
RS-232C
L
R
HEADPHONES
SHIFT
F1
F2
F3
ABC
DEF
GHI
AUDIO CH SELECT
7
8
9
1
5
2
6
3
7
4
8
CH
CH
CH
CH
CH
CH
CH
CH
PREVIEW/
JKL
MNO
PQRS
REVIEW
4
5
6
BS
AUTO
TUV
WXYZ
EDIT
1
2
3
ENT
PUSH
LOCK
0
C
T
F
REC
P8
REC
P8
REC
P8
REC
P8
FULL
> Time code display
The data, VTR status information, tape format
information
or
warning
corresponds to the direct menu buttons @ appear
on this display. (See page 16 for details of the
displays.)
? UNITY lamps
VIDEO UNITY lamp
This lights if the UNITY level applies for all the HD
or SD output levels.
AUDIO UNITY lamp
This lights if the UNITY level applies for the PCM
or CUE AUDIO input or output level. (The lighting
of the lamp complies with the setting selected for
setup menu item No.142 (AUDIO UNITY).)
@ Direct menu buttons
These buttons are used to switch directly to the
function menus on the time code display.
HOME: The most basic settings of recording,
playback and time code operations are selected
on this menu.
VIDEO: The basic input and output settings for the
video signals are selected on this menu. The
level of the HD output signals can also be
adjusted on this screen.
AUDIO: The basic input and output settings for the
audio signals are selected on this menu.
PF1: This enables user-defined menu items to be
registered in the function keys.
PF2: This enables user-defined menu items to be
registered in the function keys.
TC: The settings related to the time code are
selected on this menu. Superimposing the time
code on the display can also be set on this
screen.
10
@
A C
EJECT
XL/L/M
-cassette
Do not insert S-cassette
without adapter
SHTL
JOG
VAR
ADJUST
HOME
RF1
RF2
ASSEM
PUSH-INTER
VIDEO
TC
CUE
UNITY
INSERT
REV
FWD
AUDIO
UNITY
DIAG
MENU
STAND BY
PLAYER
RECORDER INPUT CHECK
F4
F5
F6
SERVO
REC INHIBIT
EDIT
PLAY
REC
A IN
A OUT
PRE-
ROLL
TRIM
REW
STOP
FF
SET
IN
OUT
FULL
? B
information
which
CUE: This enables up to 60 cue points to be set. In
the PAGE mode, 10 pages with 6 cue points on
each page are provided so that the cue points can
be managed on a page-by-page basis.
DIAG: This enables the warnings and hour meter
displays to be checked. On the SHIFT screen, the
error log files can be checked and deleted.
MENU: On this menu, it is possible to transfer
operation to the screen on which operations
(adjustments and saving data in or loading it from
the internal memory and IC card) relating to the
SYSTEM and SETUP menus are to be performed.
See page 38 and following for further details on
each of the function menus.
A ASSEM button
This button is used to perform assemble editing.
When it is pressed, the <ASSEMBLE> menu
appears on the time code display. Setting ASSEM
to ON using
enables assemble editing, and the
F1
lamp of the ASSEM button lights.
Even after operation is transferred by another direct
menu, the assemble mode will remain established
while the ASSEM button lamp is lighted.
To release the assemble mode, select OFF as the
ASSEM setting on the <ASSEMBLE> menu.
F1
The ASSEM button lamp now goes off and the
assemble mode is released.
B INSERT button
This button is used to perform insert editing.
When it is pressed, the <INSERT> menu appears
on the time code display, and the function menu for
selecting the signals to be edited is displayed.
To select the signals to be edited, press the
function key, and highlight the display.
highlighted display indicates that those signals are
selected.
To release the selection, press the same function
key again.
Use
to
to select the V, A1, A2, A3, A4 and
F1
F6
CUE signals; use
SHIFT
A5, A6, A7, A8 and TC signals.
C ADJUST dial
This is used for the menu and other operations.
The
+
to
to select the
F2
F6
Advertisement
Table of Contents
