Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Humandata XCM-305
Summary of Contents for Humandata XCM-305
- Page 1 Spartan-3A FPGA Board XCM-305 Series User’s Manual Ver.1.2 HuMANDATA LTD.
-
Page 2: Table Of Contents
Table of Contents Revision History ....................1 Introduction ....................1 1. Specifications ..................... 2 2. Overview ......................3 2.1. Name of Parts .......................3 2.2. Block Diagram ......................4 2.3. Power Supply ......................4 2.4. JTAG Connector ....................5 3. Configuration Switch ..................6 4. - Page 3 HuMANDATA will revise the diagram. When a problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a properly functioning product.
-
Page 4: Revision History
Mar. 4, 2013 Resister "R5" is removed to separate VIO(B) from V33A. Introduction Thank you for buying our product XCM-305. This is an evaluation board equipped with a Xilinx FPGA Spartan-3A, power, reset, and clock circuit and configuration device. -
Page 5: Specifications
17 [g] typ. 40-pin through-hole User I/O Connectors dia. 0.9 [mm], 100[mil]/2.54 [mm] pitch SIL 7-pin header (Mounted) Accessories DIL 40-pin header x2 (Cuttable) RoHS Compliance * There may be cases that these parts and specifications are changed. XCM-305 Series v1.2... -
Page 6: Overview
2. Overview 2.1. Name of Parts User LED User I/Os (CNB) User Switch MRAM Oscillator 50 MHz FPGA JTAG Serial I/F Config. Switch Power & POR User I/Os (CNA) Status LEDs Component Side Config. Device Solder Side XCM-305 Series v1.2... -
Page 7: Block Diagram
This board operates from single DC 3.3 V power supply. The external power supply should be sufficient and stabilized. Notes Please apply power to CNA and CNB with thick print pattern or cable. Please connect all ground pins. XCM-305 Series v1.2... -
Page 8: Jtag Connector
This connector is used to configure the FPGA and program the configuration device in-system. Pin assignment is as follows. Signal Name Direction JTAG Pin OUT(POW) You can use Xilinx download cable. Notice Please pay attention not to attach cables in reverse. XCM-305 Series v1.2... -
Page 9: Configuration Switch
It instructs the FPGA how to communicate with the configuration device. Please use it in default setting. 8 : Suspend Mode It controls suspend mode of the FPGA. Please see a Spartan-3A data sheet for more detail. XCM-305 Series v1.2... -
Page 10: Fpga Configuration
9. Select [Part Name] same as which is on the board. 10. Check [Verify] and [Erase Before Programming] in [Device Programming Properties] tab. 11. Select SPI PROM icon, then open [Operation] and click [Program]. Then it will show you the message “Program Succeeded”. XCM-305 Series v1.2... -
Page 11: Configuration Rate
2. Change [Configuration Rate] value in [Configuration Options]. 7. Additional Documentation and User Support The following documents and other supports are available at http://www.hdl.co.jp/en/spc/XCM/xcm-305/ Circuit Schematic Pin List Dimensional drawing PCB drawing Net List … and more. XCM-305 Series v1.2... - Page 12 Spartan-3A FPGA Board XCM-305 Series User’s Manual Ver. 1.2 ..........Mar. 4, 2013 HuMANDATA LTD. Address: 1-2-10-2F, Nakahozumi, Ibaraki Osaka, Japan ZIP 567-0034 Tel: 81-72-620-2002 (Japanese) Fax: 81-72-620-2003 (Japanese/English) URL: http://www.hdl.co.jp/en/ (Global) http://www.hdl.co.jp/ (Japan)