Honeywell NOTIFIER NFW-100XI Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Control Panel
  5. NOTIFIER NFW-100XI
  6. Manual
Honeywell NOTIFIER NFW-100XI Manual

Honeywell NOTIFIER NFW-100XI Manual

Addressable fire alarm control panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Addressable Fire Alarm Control Panel
NFW-100X
NFW-100XI
Manual
Document LS10131-001NF-E Rev: F
6/7/2022 ECN: 00009520

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NOTIFIER NFW-100XI and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Honeywell NOTIFIER NFW-100XI

Summary of Contents for Honeywell NOTIFIER NFW-100XI

  • Page 1 Addressable Fire Alarm Control Panel NFW-100X NFW-100XI Manual Document LS10131-001NF-E Rev: F 6/7/2022 ECN: 00009520...
  • Page 2 Fire Alarm & Emergency Communication System Limitations While a life safety system may lower insurance rates, it is not a substitute for life and property insurance! An automatic fire alarm system—typically made up of smoke year by a qualified fire protection specialist. Heat detectors are detectors, heat detectors, manual pull stations, audible warning designed to protect property, not life.

  • Page 3: Installation Precautions

    HARSH™, NIS™, and NOTI•FIRE•NET™ are all trademarks; and Acclimate® Plus™, FlashScan®, FAAST Fire Alarm Aspiration Sensing Technology®, Honeywell®, INSPIRE®, Intelligent FAAST®, NOTIFIER®, ONYX®, ONYXWorks®, SWIFT®, VeriFire®, and VIEW® are all registered trademarks of Honeywell International Inc.Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox®...

  • Page 4: Software Downloads

    • Your suggestion for how to correct/improve documentation Send email messages to: FireSystems.TechPubs@honeywell.com Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services. This symbol (shown left) on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

  • Page 5: Table Of Contents

    Table of Contents Section 1: Product Description ............................13 1.1: Features and Options .......................................13 1.2: Specifications........................................14 1.3: Controls and Indicators....................................16 1.4: Components ........................................16 1.4.1: Intelligent Addressable Detectors.................................17 1.4.2: Intelligent Addressable Modules ................................17 1.4.3: Addressable Device Accessories ................................17 End-of-Line Resistor Assembly................................17 Power Supervision Relay..................................17 EOL-C(R/W) Mounting Plate.................................17 1.5: Optional Modules ......................................17...
  • Page 6 Table of Contents ANN-BUS Device Addressing ................................35 N-ANN-80 Remote Fire Annunciator ..............................35 N-ANN-100 Remote Fire Annunciator ..............................37 N-ANN-S/PG Serial/Parallel Interface Module .............................38 N-ANN-I/O LED Driver Module ................................40 N-ANN-LED Annunciator Module ................................42 N-ANN-RLY Annunciator Module................................44 2.8.5: Printer ........................................45 Printer Configuration ....................................45 2.8.6: NFC-FFT Firefighter Telephone ................................46 2.8.7: FWSG Wireless Gateway ..................................46 2.9: Automatic Audio Panel Control..................................46...
  • Page 7 Table of Contents Communicator Installed..................................84 POTS Settings......................................84 IP Settings .......................................85 Primary and Secondary Communication Paths ............................86 Trouble Report Limit (Dialer Runaway Prevention) ..........................89 Report Style ......................................89 Event Codes ......................................89 3.5.8: Annunciators......................................92 ANN-BUS Setup....................................92 ANN-BUS Options ....................................99 3.5.9: Password Change....................................101 Invalid Password....................................101 Incorrect Password/Timeout .................................101 3.5.10: Clear Program....................................102 3.5.11: Program Check ....................................102...
  • Page 8 Table of Contents 4.24.4: Timers .......................................118 4.24.5: NACs ........................................118 4.24.6: Relays .......................................118 4.24.7: Program Check ....................................118 4.24.8: History ......................................119 4.24.9: Annunciators.....................................119 4.24.10: Communicator ....................................119 4.24.11: Print.........................................120 Chamber Value .....................................121 Drift Compensation....................................121 Maintenance Alert....................................121 4.24.12: Time-Date .......................................122 4.24.13: Battery Charger....................................122 4.24.14: 4XTM Supervision ..................................122 4.24.15: Remote Sync....................................122 Section 5: Central Station Communications - POTS Transmission .................
  • Page 9 Table of Contents Appendix G: Central Station Points..........................153 Appendix H: NFPA Requirements..........................155 Appendix I: Open/Short/Ground Trip Values ......................156 Index ....................................157 Slide-in Labels ................................161 NFW-100X Series Fire Alarm Control Panel Operating Instructions ..............................163 NFW-100X Manual — P/N LS10131-001NF-E:F 6/7/2022...
  • Page 10 It is imperative that the installer understand the requirements of the Authority Having Jurisdiction (AHJ) and be familiar with the standards set forth by the following regulatory agencies: • Underwriters Laboratories • National Fire Protection Association Before proceeding, the installer should be familiar with the following documents. NFPA Standards NFPA 72 National Fire Alarm Code NFPA 70 National Electrical Code...
  • Page 11 250V ES50- PCA REV ES200- PCA REV NFW-100X Manual — P/N LS10131-001NF-E:F 6/7/2022...
  • Page 12 Peripheral Devices and Their Documents: ANN Audio Control for NFC-50/100 Doc. #LS10001-001NF-E N-ANN-RLY N-ANN-S/PG N-ANN-100 N-ANN-I/O Relay Card N-ANN-80 Printer Driver LCD Text Annunciator N-ANN-(R)LED LED Driver Doc. #53318 LCD Text Annunciator Doc. #151424 Doc. #LS10205-001NF-E LED Display Doc. #151243 Doc.

  • Page 13: Section 1: Product Description

    Section 1: Product Description The NOTIFIER NFW-100X is an addressable FACP (Fire Alarm Control Panel) with a pre-installed communicator card that is compact, cost effective, intelligent, and has an extensive list of powerful features which offers the latest in fire protection technology. The power supply and all electronics are housed in a metal cabinet, providing a complete fire control system for most applications.

  • Page 14: Specifications

    Product Description Specifications • Compatible with FireWarden’s and NOTIFIER’s addressable devices (refer to the FireWarden/ONYX SLC Wiring Manuals for a list of compatible addressable devices) • Optional 4XTM module (conventional reverse polarity/city box transmitter) • ANN-BUS for connection to following optional modules: N-ANN-80 Remote Annunciator (UL applications only) N-ANN-100 (FM only) N-ANN-I/O LED Driver...
  • Page 15 Specifications Product Description Power-limited circuit Refer to the Device Compatibility Document for listed compatible devices Note: Refer to the programming section to configure power as resettable/non-resettable. Remote Sync Output - TB8 Remote power supply synchronization output 24 VDC nominal special application power Maximum current is 350 mA End-of-Line Resistor: 4.7KΩ...

  • Page 16: Controls And Indicators

    Product Description Controls and Indicators 1.3 Controls and Indicators LCD Display The FACP uses an 80-character (4 lines X 20 characters) high viewing angle LCD display. The display includes a long life LED backlight that remains illuminated. If AC power is lost and the system is not in alarm, the LED SYSTEM NORMAL backlight will turn off to conserve batteries.

  • Page 17: 1: Intelligent Addressable Detectors

    Optional Modules Product Description ® • Dialing the Central Station(s) number: default is Touch-Tone , programmable to rotary • For tone burst or touchtone type formats: discern proper Ack and Kissoff tone(s). The frequency and time duration of the tone(s) varies with the transmission format.

  • Page 18: Accessories

    Product Description Accessories 1.6 Accessories 1.6.1 FS-Tools Programming Utility The FS-Tools Programming Utility can be used to locally or remotely program the FACP from most Windows® compatible computers (PC), running Windows 7 or newer, 32 or 64 bit. The FACP program files can also be created and stored on the PC for future download to the con- trol panel.

  • Page 19: 7: Nfc-Fft

    Accessories Product Description 1.6.7 NFC-FFT An NFC-FFT Fire Fighter Telephone provides supervision, annunciation, and control for local and remote telephone handsets. The NFC- FFT’s keypad provides indications of phone activation and corresponding trouble conditions. . 1.6.8 FWSG Wireless Gateway The FWSG Wireless Gateway acts as a bridge between a group of wireless fire devices and a FlashScan SLC loop on the NFW-100X. It is powered by the SLC loop or by a regulated, external 24VDC UL-listed power supply evaluated for life safety.

  • Page 20: Getting Started

    Before connecting the control panel to the public switched telephone network, the installation of two RJ31X jacks is necessary. If trouble is experienced with this equipment, for repair or warranty information, please contact: Manufacturer: Honeywell International, Inc. 12 Clintonville Road Northford, CT 06472...

  • Page 21: Section 2: Installation

    Section 2: Installation The cabinet may be either semi-flush or surface mounted. The cabinet mounts using two key slots and two 0.250” (6.35 mm) diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage.
  • Page 22 Installation Mounting the Backbox Semi-Flush Mounting Do not recess box more Hinge Slot for optional than 3.875” into wall to Dress Panel avoid covering venting holes on top of box. Mounting slots for optional Trim Ring Semi-flush mounting hole Hinge Slot for optional Dress Panel Figure 2.2 NFW-100X Cabinet Mounting NFW-100X Manual —...
  • Page 23 Mounting the Backbox Installation 5.207” (13.23cm) 16.822” (42.73 cm) 6.537” (16.6cm) Width Depth Height 19.26” (48.92 cm) Right Side Left Side Bottom Figure 2.3 NFW-100X Cabinet Dimensions An optional Trim Ring (P/N TR-CE-B) is also available for semi-flush mount installations. NFW-100X Manual —...

  • Page 24: Power

    Installation Power 2.2 Power WARNING: RISK OF EQUIPMENT DAMAGE AND PERSONAL INJURY SEVERAL DIFFERENT SOURCES OF POWER CAN BE CONNECTED TO THIS PANEL. DISCONNECT ALL SOURCES OF POWER BEFORE SERVICING. THE PANEL AND ASSOCIATED EQUIPMENT MAY BE DAMAGED BY REMOVING AND/OR INSERTING CARDS, MODULES OR INTERCONNECTING CABLES WHILE THIS UNIT IS ENERGIZED.

  • Page 25: 3: Special Application Dc Power Output Connection

    Relays Installation 2.2.3 Special Application DC Power Output Connection All Special Application DC power outputs are power-limited (refer to “UL Power-limited Wiring Requirements” on page 28). Power-limited Resettable or Non-resettable Power Power-limited Non-resettable or Resettable Power 1.0 amperes max., 24 VDC nominal filtered, programmable 1.0 amperes max., 24 VDC nominal filtered, non- resettable or non-resettable power can be drawn from TB11 resettable or resettable power is programmable.

  • Page 26: 1: Class B Nac Wiring

    Installation Notification Appliance Circuits 2.4.1 Class B NAC Wiring 4 Class B Notification Appliance Circuits, supervised and power-limited - 4.7 kΩ, ½ watt P/N:71252 UL listed NAC 3 NAC 1 NAC 4 NAC 2 Polarized Bells Polarized Bells Polarized Strobes Polarized Strobes Polarized Horns Polarized Horns...

  • Page 27: Remote Synchronization Output

    Remote Synchronization Output Installation 2.5 Remote Synchronization Output Synchronization is a feature that controls the activation of notification appliances in such a way that all devices will turn on and off at exactly the same time. This is particularly critical when activating strobes which must be synchronized to avoid random activation and a potential hazard to individuals.

  • Page 28: Ul Power-Limited Wiring Requirements

    Installation UL Power-limited Wiring Requirements 2.6 UL Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” (6.35 mm) away from any nonpower-limited circuit wiring and nonpower-limited circuit wiring must enter and exit the cabinet through different knockouts and/or conduits.

  • Page 29: Ipots-Com Communicator

    IPOTS-COM Communicator Installation 2.7 IPOTS-COM Communicator Two independent telephone lines can be connected to the control panel via the IPOTS-COM Phone/IP Communication Module. Telephone line control/command is made possible via double line seizure as well as usage of an RJ31X style interconnection. Note that it is critical that the IPOTS-COM Digital Communicator be located as the first device on the incoming telephone circuit to properly function.

  • Page 30: Dip Switches

    SW2: 6-position dip switch- FUTURE USE- No configuration necessary. • SW3: 2-position dip switch- Factory Settings- Do not change unless instructed to do so by Honeywell. 2.8 Optional Module Installation WARNING: RISK OF ELECTRIC SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING.

  • Page 31: 3: 4Xtm Transmitter Module Installation

    Optional Module Installation Installation 2.8.3 4XTM Transmitter Module Installation The 4XTM provides a supervised output for a local energy municipal box transmitter in addition to alarm and trouble reverse polarity. A jumper option allows the reverse polarity circuit to open with a system trouble condition if no alarm condition exists. A disable switch allows disabling of the transmitter output during testing to prevent accidental calling of the monitoring service.

  • Page 32: 4: Ann-Bus Annunciators/Modules

    Installation Optional Module Installation For proper 4XTM operation, the output relays must be programmed for the factory default settings: Alarm Relay 1, Trouble Relay 2 and Supervisory Relay 3. When the installation has been complete, enable the 4XTM module by sliding the disconnect switch to the left. Test system for proper operation.

  • Page 33: Wiring Distance Calculation Example

    Optional Module Installation Installation In general, the wire length is limited by resistance, but for heavier wire gauges, capacitance is the limiting factor. Maximum length can never be more than 6,000 feet (1,800 m), regardless of gauge used. The following formulas were used to generate the wire distances: 2.0 Volts Maximum Resistance (Ohms) Total Worst Case Current Draw (amps)
  • Page 34 Installation Optional Module Installation Figure 2.18 illustrates the wiring between the FACP’s Secondary ANN-BUS and ANN-BUS devices. ANN-BUS and power wiring are supervised and power-limited 4 3 2 1 ANN-BUS Device Secondary 24 VDC ANN-BUS nonresettable NFW-100X Figure 2.18 Secondary ANN-BUS wiring to ANN-BUS Device ...

  • Page 35: Ann-Bus Device Addressing

    Optional Module Installation Installation ANN-BUS Device Addressing Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the FACP. A 5-position DIP switch on each device is used to set this address. The address set for these devices must also be programmed at the FACP for the specific device (refer to the programming section titled “ANN-BUS Setup”...
  • Page 36 Installation Optional Module Installation  Mounting The N-ANN-80 can be surface or semi-flush mounted to a single, double or 4” square electrical box. Select and remove the appropriate knockout(s), pull the necessary wires through the knockouts and mount the annunciator in or on the wall depending on the type of installa- tion desired.

  • Page 37: N-Ann-100 Remote Fire Annunciator

    Optional Module Installation Installation After all connections are made, remove extra wire from inside of annunciator by dressing it neatly through wire channel, with any excess wire pushed back through hole into electrical box ANN-BUS and power wiring are supervised and power-limited 4 3 2 1 ANN-BUS Device Primary...

  • Page 38: N-Ann-S/Pg Serial/Parallel Interface Module

    Installation Optional Module Installation  Programming Following installation and wiring of the N-ANN-100 LCD annunciator to the FACP, the annunciator must be added to the system via FACP programming. Refer to the programming section titled “ANN-BUS Setup” on page 92 in this manual for detailed programming information. ...

  • Page 39: Setting Printer Options

    Optional Module Installation Installation  Setting Printer Options Refer to the documentation supplied with the PRN-7 printer for instructions on using the printer menu controls. Set the printer options (under the menu area) as shown in the following table: Option Setting Option Setting...

  • Page 40: N-Ann-I/O Led Driver Module

    Installation Optional Module Installation ANN-I/O LED Driver Module  ANN-I/O Board Layout Figure 2.22 illustrates the N-ANN-I/O board showing locations of screw terminals for connection to the FACP, pin connectors for connect- ing LEDs and the DIP switch for selecting the ANN-BUS ID number. LED Out LED Out LED Out...
  • Page 41 Optional Module Installation Installation  ANN-I/O Connection to FACP The N-ANN-I/O connects to the FACP via the ANN-BUS as illustrated in Figure 2.23. After the N-ANN-I/O is connected to the panel, it must be added to the system via FACP programming. Refer to the section titled “ANN-I/O Options” on page 93. 20 21 LED Out LED Out...

  • Page 42: N-Ann-Led Annunciator Module

    Installation Optional Module Installation Pin # LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Cathode LED9 LEDs LED10 LED Power Anode no connection Pin # LED11 LED12 LED13 LED14 LED15 LED16 LED17 LED18 Cathode LED19 LEDs LED20 Anode LED Power no connection Figure 2.24 ANN-I/O LED Wiring N-ANN-LED Annunciator Module...
  • Page 43 Optional Module Installation Installation  Specifications • Max. ANN-BUS Voltage: 24 VDC • Max. Current: Alarm: 68 mA Standby: 28 mA • Operating Temperature: 32°F to 120°F (0°C to 49°C) • For indoor use in a dry location only  Mounting/Installation The N-ANN-LED Module is supplied with a metal backbox, mounting bracket, and cover.

  • Page 44: N-Ann-Rly Annunciator Module

    Installation Optional Module Installation ANN-RLY Annunciator Module  Specifications • Operating Voltage: 24 VDC • Max. Current: Alarm: 75 mA Standby: 15 mA • Operating Temperature: 32°F to 120°F (0°C to 49°C) • For indoor use in a dry location only ...

  • Page 45: 5: Printer

    Optional Module Installation Installation  N-ANN-RLY Board Layout and Connection to FACP Figure 2.29 illustrates the N-ANN-RLY board showing locations of screw terminals for connection to the FACP and the DIP switches for selecting the ANN-BUS ID number. ANN-BUS (ID#) Address DIP switch 1 2 3 4 5 6 7 8 ANN-BUS and power wiring are...

  • Page 46: 6: Nfc-Fft Firefighter Telephone

    Installation Automatic Audio Panel Control 2.8.6 NFC-FFT Firefighter Telephone The NFC-FFT connects from TB11 (non-resettable aux power) on the FACP to the DC Power input on the NFC-FFT board. NFC-FFT NFW-100X Figure 2.30 NFC-FFT Connections 2.8.7 FWSG Wireless Gateway The FWSG connects to the FACP’s SLC connection at TB10. The FWSG can be powered by either the SLC or an external 24 VDC power source.
  • Page 47 Automatic Audio Panel Control Installation Connect the NFC-50/100 panel’s FACP Data Bus at TB13 to TB9 on the NFW-100X FACP. NFC-50/100 to other ANN devices NFW-100X Figure 2.32 FACP Connection to NFC-50/100 Series Audio Panel The only connection between the FACP and NFV-25/50ZS Series audio panel is a pair of communication wires connected between the A(+)/B(-) terminals on TB9 of the FACP and TB1 terminals 2 &...

  • Page 48: Section 3: Programming

    Section 3: Programming NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION AND OTHER INVOLVED PARTIES This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to specific values or not used at all as indicated below: Program feature or Permitted in...

  • Page 49: User Programming

    User Programming Programming 3.1 User Programming The NFW-100X is completely field programmable and requires no special software skills. While programming the NFW-100X, the fire pro- tection capabilities of the control panel are enabled. Site-specific programming may be accomplished in any of the following ways: •...

  • Page 50: 1: Administrator Role

    Programming Users and Passwords 3.4.1 Administrator Role Password Change-Administrator The factory set password must be changed to clear the Password Fault from the panel. Pressing the Enter key on home screen will cause the following screen to be displayed: 1=READ STATUS MODE 2=LOGIN Press 2 to login to the panel.

  • Page 51: Password Change- User

    Users and Passwords Programming A flashing cursor will appear in the center of the display. Enter the default password, 00000000. Then, enter a new, valid eight digit password in the second line. Once the last digit is entered, the following screen will be displayed: MODIFY ADMIN 1 VERIFY PASSWORD NEW:...

  • Page 52: Assign Role

    Programming Users and Passwords Select 1 to enable the User account. Each press of the 1 key will toggle the screen between Enabled Yes and Enabled No. Press 3 to assign a password. Note that if a user is disabled at any time, the password will need to be reassigned. MODIFY USER X ENTER PASSWORDS ADMIN X:...

  • Page 53: 2: User Role

    Master Programming Level Programming The following screen will appear when the password is entered: ADMIN X ACCOUNT 1=MODIFY ACCOUNTS 2=VIEW CYBER SEC LOG 3=NOT USED Select 1 to modify an account. MODIFY ACCOUNTS 1=ADMINISTRATORS 2=USERS 3=NOT USED Select 2 to modify a User account. MODIFY USER 1=USER 1 2=USER 2...

  • Page 54: 1=Autoprogram

    Programming Master Programming Level Select the appropriate User login ID: LOGIN FOR USER X ENTER PASSWORD Enter the User’s Master level password. Only a user with master level programming rights can access panel programming. The following screen will appear: MASTER MENU 1=PROGRAMMING MODE 2=FS-TOOL UP/DWNLOAD 3=USB UP/DOWNLOAD...

  • Page 55: 2: Point Program

    Master Programming Level Programming 3.5.2 Point Program The Point Program option allows the programmer to add a new addressable device to the SLC loop, delete an PROGRAMMING 1=AUTOPROGRAM existing device from the loop or change the programming for an existing device. Pressing 2, while viewing Pro- 2=POINT PROGRAM gramming Screen #1, will select the Point Program option and display the following screens: 3=ZONE SETUP...
  • Page 56 Programming Master Programming Level  Delete Detector Pressing 2 in the Detector Screen will display the Delete Detector Screen which allows the programmer to DETECTOR 1=ADD delete a specific detector: 2=DELETE DELETE DETECTOR 3=EDIT ENTER DETECTOR# Detector Screen Delete Detector Screen A flashing cursor will appear in the position of the first asterisk to the left.
  • Page 57 Master Programming Level Programming ZNNN - represents the first of five possible software zones that the detector is assigned to (NNN = the three digit zone number from 000 - 099) V or * - indicates whether or not alarm verification is enabled (V = alarm verification enabled and * = alarm verification disabled) W or * - indicates whether or not walktest is enabled (W = walktest enabled and * = walktest disabled) X or * - indicates whether or not the detector is wireless (X = wireless detector and * = wired detector) 1D017 - represents the Loop, Device type and Device address (1=SLC Loop, D=Detector and 017=Detector Address 017)
  • Page 58 Programming Master Programming Level Fire/CO response is programmable (Alarm, Supv, or None) User-Defined-12 same as previous (Fire/CO) Photo/CO response is programmable (Alarm, Supv, or None) User-Defined-13 same as previous (Photo/CO) While viewing either Detector Type screen, select the type of detector being programmed by pressing the corresponding keypad number key. The display will return to Edit Detector Screen #2 and indicate the selection next to the Type option.
  • Page 59 Master Programming Level Programming Program an output, such as a control module, for Pre-signal activation by assigning zone Z98 to it. This control module may be connected to a signaling device used to indicate a Pre-signal condition (do not use a Notification Appliance Circuit for this purpose) Enable zones Z001 and Special Purpose Zone Pre-signal 98 and set the Pre-signal delay timer to some value With the preceding program settings, when the detector with address 005 is activated, zone Z98 will cause its associated control module to activate immediately, sounding the connected signaling device to indicate the Pre-signal condition.
  • Page 60 Programming Master Programming Level • Temporal 4 - ½ Second On, ½ Second Off, ½ Second On, ½ Second Off, ½ Second On, ½ Second Off, ½ Second On, 1½ Seconds Off The sounder base volume has two settings: Low or High. Press 1 while viewing Sounder Base Screen #2 until SOUNDER BASE 1=ZONE ASSIGNMENT the display reads Low or High as desired.

  • Page 61: Module Programming

    Master Programming Level Programming Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note 1=STANDARD ADJECTIVE 2=STANDARD NOUN that the keypad down arrow key must be pressed to see all the Noun screens. Press the number corresponding to 3=CUSTOM ADJECTIVE the noun that is to be used as a descriptor for the location of the detector currently being programmed.
  • Page 62 Programming Master Programming Level When the last digit is keyed-in, the following screen will be displayed: ADD MODULE 1=CON 3=MON 2=CON:WL 4=MON:WL Add Module Screen #2 Pressing 1 for Control Module, 2 for Wireless Control Module, 3 for Monitor Module, or 4 for Wireless Monitor Module will cause the fol- lowing screen to be displayed: ADD MODULE MODULE#...
  • Page 63 Master Programming Level Programming If the selected address has been added to programming and a module (such as a monitor module) with the selected address is physically installed on the SLC and is communicating with the control panel, the following screen will be displayed: NORMAL MONITOR <ADJ><NOUN>...
  • Page 64 Programming Master Programming Level User-Defined-2 same as previous (Waterflow) Monitor Fire Alarm User-Defined-3 same as previous (Monitor) Future not used Future not used Smoke-Conventional Fire Alarm User-Defined-5 same as previous (Smoke-Conventional) Heat Conventional Fire Alarm User-Defined-6 same as previous (Heat-Detector) Medic Alert General Purpose Signaling, latching User-Defined-7...
  • Page 65 Master Programming Level Programming Wireless The Wireless selection will update automatically if the system recognizes a wireless device. If the module is wireless, the display reads Wire- less Yes. If the module is wired, the display will read Wireless No. Fore more information on the SWIFT wireless network, refer to the SWIFT manual, #LS10036-000NF-E.
  • Page 66 Programming Master Programming Level Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note 1=STANDARD ADJECTIVE 2=STANDARD NOUN that the keypad down arrow key must be pressed to see all the Noun screens. Press the number corresponding to 3=CUSTOM ADJECTIVE the noun that is to be used as a descriptor for the location of the monitor module currently being programmed.
  • Page 67 Master Programming Level Programming ZNNN - represents the first of five possible software zones that the module is assigned to (NNN = the three digit zone number from 000 - 099) 1M002 - represents the Loop, Device type and Device address (1 = SLC Loop, M=Module and 002 = Module Address 02) To change the programming for the displayed module, press the keypad down arrow key to view the following Edit Control screens: EDIT CONTROL EDIT CONTROL...
  • Page 68 Programming Master Programming Level Zone Assignment A maximum of five zones can be programmed to each addressable control module. Pressing 2 while viewing Edit Control Screen #3 displays the following screen: ZONE ASSIGNMENT Z000 Zone Assignment Screen Note that Z*** represents the Zone Number(s) corresponding to this device. The factory default for an unprogrammed device is Z000 for general alarm zone.

  • Page 69: 3=Zone Setup

    Master Programming Level Programming Description The Description selection allows the programmer to enter additional information about the control module cur- EDIT CONTROL 1=ADJECTIVE/NOUN rently being programmed. This information will be displayed as part of the device label on the display. Pressing 2=DESCRIPTION 2 while viewing Edit Control Screen #4 will cause the following screen to be displayed: DESCRIPTION...

  • Page 70: Disable

    Programming Master Programming Level Disable Pressing 2 for Disable, while viewing Zone Setup Screen #1, displays the following: ZONE SETUP 1=ENABLE ZONE TO DISABLE 2=DISABLE 3=SPECIAL PURPOSE Zone Setup Screen #1 Disable Screen This screen allows the programmer to disable zones, one at a time. A flashing cursor appears next to the Z, prompting the programmer to enter a three digit zone number (001 - 099).

  • Page 71: Zones Enabled

    Master Programming Level Programming This display will show all of the zones that have been programmed into the control panel. Note that an up and/or down arrow may appear in the upper right corner of the display, indicating that additional screens of zone information exists. Press the up or down arrow keys to view the additional zones.

  • Page 72: Zones Available

    Programming Master Programming Level To program a waterflow circuit as nonsilenceable, refer to “System Setup” on page 72. NOTE: Zone Types are only relevant for Central Station reporting. Changing a zone type will only change how it is reported to the Central Station.

  • Page 73: Function Keys

    Master Programming Level Programming • Banner: This option allows the user to change the top two lines of the LCD display from the blank factory default readout to a user defined readout when the control panel is in Normal condition. •...

  • Page 74: Banner

    Programming Master Programming Level Each function key can be assigned to control any of the 4 onboard NAC circuits on the NFW-100X. By pressing the 2 key while viewing the Function Keys Screen #2 the following screen displays, allowing the user to select the desired NAC circuit(s). F(X) NACS 1=NAC 1 3=NAC 3...
  • Page 75 Master Programming Level Programming  Time To change the time, press 1 while viewing the Time-Date Screen. The following screen will be displayed: ENTER TIME 10:00 AM 1=AM 2=PM Time Screen A flashing cursor is located toward the top left of the display. Below the cursor is the current time. To change the time, enter the two-digit hours followed by the two-digit minutes.

  • Page 76: Timers

    Programming Master Programming Level Timers Timer delays for PAS, Pre-signal and waterflow activation can be programmed by pressing 1 while viewing SYSTEM SETUP 1=TIMERS System Setup Screen #2. The following screen will be displayed: 2=NAC TIMERS 3=RELAYS TIMERS TIMERS 1=IN SUITE SIL. 1=PAS DELAY 1=AC LOSS DELAY System Setup Screen #2...
  • Page 77 Master Programming Level Programming Pressing 2 while viewing AC Loss Delay Screen #1 will display the following: AC LOSS DELAY RANGE 00-23 AC Loss Delay Screen #2 A flashing cursor will appear in the lower left corner of the display. Type the two digit AC loss reporting delay in hours (00 to 23 hour delay). When the second digit is entered, the display will return to AC Loss Delay Screen #1.

  • Page 78: Nac (Notification Appliance Circuit)

    Programming Master Programming Level  Suite Resound (Canadian Mode Only) The Suite Resound feature is only available when the FACP is in Canadian mode of operation. When enabled, TIMER 1=IN SUITE SIL. this feature will resound all outputs and NACs that were silenced by the In Suite Silence timer (if there is an 2=SUITE RESOUND unacknowledged fire alarm on the panel) after a programmed length of time.
  • Page 79 Master Programming Level Programming Blank None  Silenceable Pressing 3 while viewing NAC Screen #1 will cause the display to change to Silenceable No. This will prevent the selected main circuit board NAC from being silenced by pressing the Alarm Silence key or by the Auto Silence feature. Each press of the 3 key will cause the dis- play to toggle between Silenceable Yes and Silenceable No.
  • Page 80 Programming Master Programming Level If an F2 switch has been pressed, the Alarm LED will turn from flashing to steady. Any NACs currently in 1st stage activation will remain in 1st stage. Pressing the Acknowledge switch does not affect NACs already in 2nd stage activation. If an F3 button in pressed, the NACs will progress to the second stage.

  • Page 81: Relays

    Master Programming Level Programming  MNS Active The MNS Active feature, when enabled, allows the selected NAC to activate when an MNS Event occurs and NAC # the FACP receives a message from the NFC-50/100. The selected NAC will activate regardless of zone map- 1=SYNC TYPE 2=MNS OVERRIDE ping.

  • Page 82: Waterflow Silenceable

    Programming Master Programming Level Special Zone 95 CO Active Special Zone 94 In Suite Silence Control Module Auto Silence Timer In Suite Silence Timer In Suite Resound Timer Programmable NAC Silence Inhibit ANN-Bus annunciator keys enable • Control modules are no longer associated with the auto silence setting for NAC 1. •...

  • Page 83: Language

    Master Programming Level Programming Language The language option is used to change the text on the panel display to either English or French. Pressing the 3 SYSTEM SETUP 1=AUX POWER key will cause the display to offer a choice of 1=English and 2=French. 2=TROUBLE REM 24HR 3=LANGUAGE...

  • Page 84: 7: Communicator

    Programming Master Programming Level Pressing 1 while viewing the Erase History Screen will erase all events from the History file. During this process, the display will read as fol- lows: ERASING HISTORY PLEASE WAIT Erase History Wait Screen After the History file has been erased, the display will return to the History Screen. 3.5.7 Communicator The communicator settings allow the user to configure the settings for the pre-installed IPOTS-COM and PROGRAMMING...

  • Page 85: Ip Settings

    Master Programming Level Programming Supervised Phone Line The Supervised Phone Line feature allows the user to disable the supervision of Phone Lines when using an POTS LINE X 1=ENABLED alternate means of secondary transmission path. The factory default setting is Phone Line (X) supervised. 2=TYPE Supervision must be set to Yes if the selected transmission path is POTS.

  • Page 86: Primary And Secondary Communication Paths

    Programming Master Programming Level  In the event that the Communicator needs to be replaced, the device will need to be re-registered with Alarm- IP SETTINGS 1=DHCP ENABLED Net. AlarmNet will issue a PIN to be entered into the panel for verification. Pressing 3 on the IP Settings screen 2=STATIC SETTINGS will display the following.
  • Page 87 Master Programming Level Programming Account Code Pressing 3 while viewing POTS (XXX) Path Screen #1 will cause the following screen to be displayed: POTS XXX COMM PATH 1=ENABLED ACCOUNT CODE 2=ACCT CODE 000000 ENTER 6 DIGITS POTS Comm Path Screen #1 Account Codes Screen The Account Code, which is assigned by a Central Station, depends on the communication format being used.
  • Page 88 Programming Master Programming Level  Ethernet To configure the communication method to contact central station as an Ethernet connection, select 2 for Ether- XXX COMM PATH 1=POTS net from the Comm Path Screen. The following screens will display. 2=ETHERNET 3=CELLULAR ETHERNET OPTIONS ETHERNET OPTIONS Comm Path Screen #1...

  • Page 89: Trouble Report Limit (Dialer Runaway Prevention)

    Master Programming Level Programming Supervision Settings Pressing 1 while viewing Ethernet Options Screen #2 will cause the display to toggle between the 4 supervi- CELLULAR OPTIONS 1=SUPV. SETTINGS sion setting options. Toggle to select NFPA 2010 Sole Path, NFPA 2010 Dual Path, NFPA 2013 Sole Path, or NFPA 2010 DUAL PATH NFPA 2013 Dual Path.
  • Page 90 Programming Master Programming Level Pressing the down arrow key allows viewing of all Events associated with the selected Communication Format. Pressing the number corre- sponding to the event displayed in each screen will display its default event code which can be customized by the programmer. For example, pressing 1 for Pull Station will display the following screen which allows the Event Code to be changed from the default value.
  • Page 91 Master Programming Level Programming TAMPER Zone Point MON-USER-DEF-11 Zone Point MON SUPERVISORY Zone Point MON-USER-DEF-12 Zone Point MON SUPERV AUTO Zone Point MON-USER-DEF-13 Zone Point HVAC OVRRIDE Zone Point POWER MON Zone Point MON-USER-DEF-14 Zone Point TROUBLE MON POINT_FAULT code will always be transmitted MON-USER-DEF-15 POINT_FAULT code will always be transmitted PROCESS MON...

  • Page 92: 8: Annunciators

    Programming Master Programming Level PRI ANN CLASS A REMOTE SYNC DIS NAC 1 DISABLE NAC 2 DISABLE NAC 3 DISABLE NAC 4 DISABLE MEMORY FAULT CHARGER FAULT OPTION CARD 1 FAULT REMOTE SYNC FAULT ZONE DISABLE PWRMOD24 FAULT AUX 1 CLASS A FAUL ANN-BUS COMM FAULT DISPLAY COMM FAULT NO_DEVICES_INSTLLD...
  • Page 93 Master Programming Level Programming  Modules Installed If an ANN-BUS module is installed, press 2 for Modules Installed to select ANN-BUS addresses for the mod- ANN XXX 1=ENABLED ule(s). The only difference between the two programming screens are the addresses. The Primary Bus module 2=MODULES INSTALLED addresses will have a prefix of “1-”...
  • Page 94 Programming Master Programming Level ANN-I/O Zone Option If Zone is selected as the module option, the first ten LEDs on the first N-ANN-I/O module will display the system status information. The remaining 30 LEDs on the first module and 40 LEDs on the remaining modules will display the active/alarm status of each zone in the Zone Range programmed for that particular module.
  • Page 95 Master Programming Level Programming ANN-I/O Point Option If Point is selected as the module option, the first ten LEDs on the first N-ANN-I/O module will display the system status information. The remaining 30 LEDs on the first module and 40 LEDs on each additional module will display the active/alarm status of each point in the Point Range programmed for that particular module.
  • Page 96 Programming Master Programming Level ANN-LED Options Pressing 2 for Module Options while viewing the (XXX) ANN-BUS Address Screen when the ANN-LED ANN XXX 1=ENABLED option is selected, will display the following screen: 2=MODULES INSTALLED 3=AUTO-CONFIGURE ANN-LED - ADDR X-1 ANN-LED - ADDR X-1 ANN-LED - ADDR X-1 ANN XXX Screen #2 1=POINT/ZONE...
  • Page 97 Master Programming Level Programming ANN-LED Zone Option - Alarm, Trouble and Supervisory If Zone is selected as the module option, and the module is programmed to annunciate alarms, troubles and supervisories, the first ten LEDs on the first N-ANN-LED module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on the remaining modules will display the alarm, trouble and supervisory status for each of the ten zones in the Zone Range pro- grammed for that particular module.
  • Page 98 Programming Master Programming Level Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Point 031 Point 032 Point 033 Point 034 Point 035 Active/Alarm Active/Alarm Active/Alarm Active/Alarm Active/Alarm Point 036 Point 037 Point 038 Point 039...

  • Page 99: Ann-Bus Options

    Master Programming Level Programming ANN-RLY Options Pressing 2 for Module Options while viewing the ANN-BUS Address Screen when the ANN-RLY option is ANN XXX 1=ENABLED selected, will cause the following screen to be displayed: 2=MODULES INSTALLED 3=AUTO-CONFIGURE ANN-RLY - ADDR. X-1 ANN XXX Screen #2 1=RLY 1 ZONE 000...
  • Page 100 Programming Master Programming Level  ANN-S/PG (Print) Options The Print option allows the programmer to configure the optional printer. Pressing 1 while viewing the ANN- XXX ANN-BUS 1=ANN-S/PG OPTIONS BUS screen will display the following screens: 2=ANN-LED OPTIONS 3=ANN-80/100 OPTIONS ANN-S/PG OPTIONS ANN-S/PG OPTIONS ANN-S/PG OPTIONS...

  • Page 101: 9: Password Change

    Master Programming Level Programming The Acknowledge Button Enable (ACK BTN ENABLE) option allows the programmer to select whether the Ack/Step button on any installed N-ANN-80 or N-ANN-100 annunciator will function normally or always be ignored. Pressing 3 while viewing the ANN-80/100 Options Screen #1 causes the display to toggle between Ack Btn Enable Yes (Ack/Step button functions normally) and Ack Btn Enable No (Ack/Step button never functions).

  • Page 102: 10: Clear Program

    Programming Master Programming Level 3.5.10 Clear Program Pressing 2 while viewing Programming Screen #4, will select the Clear Program option. This will cause the PROGRAMMING 1=PASSWORD CHANGE LCD to display the following screen: 2=CLEAR PROGRAM 3=PROGRAM CHECK CLEAR PROGRAM 1=WHOLE SYSTEM Programming Screen #4 2=ALL POINTS Clear Program Screen...

  • Page 103: Maintenance Programming Level

    Maintenance Programming Level Programming 3.6 Maintenance Programming Level To access Maintenance Programming mode, press the Enter key. The LCD will display the following: 1=READ STATUS MODE 2=PROGRAMMING MODE 3=FSTOOL UP/DOWNLOAD 4=USB UP/DOWNLOAD To enter the Maintenance Programming mode, press 2. The display will read as follows: PROGRAMMING ENTER PASSWORD When the Maintenance level password (default 11111111) is entered, the following screen will appear:...

  • Page 104: 3=Program Check

    Programming Maintenance Programming Level The History feature allows the operator to view control panel events which have been stored in a history file in memory and erase the con- tents of the history file Pressing 1 while viewing the History screen will cause the following screen to be displayed: HISTORY 1=VIEW ALL 2=VIEW ALARMS...

  • Page 105: 4: Walktest

    Maintenance Programming Level Programming 3.6.4 Walktest To perform a walktest, press 1 while viewing Maintenance Screen #2. The following screen will be displayed: PROGRAMMING 1=WALKTEST WALKTEST 2=SYSTEM 1=SILENT 3=ZONE SETUP 2=AUDIBLE Maintenance Screen #2 3=VIEW RESULT Walktest Screen The operator can press 1 to perform a silent walktest or 2 to perform an audible walktest. Pressing 1 or 2 will cause the control panel to enter Walktest Mode and will display the following screen: UNIT IN WALKTEST 1=VIEW WALKTEST LOG...

  • Page 106: 6: Zone Setup

    Programming Maintenance Programming Level Pressing 1 while viewing NAC Screen #1 will cause the display to change to NAC1 Yes. This will allow the selected main circuit board NAC to activate its devices. Each press of the 1 key will cause the display to toggle between NAC1 Yes and NAC1 No. The same action is per- formed for the other 3 NAC circuits by selecting the number of the desired output circuit.
  • Page 107 Maintenance Programming Level Programming Pressing 2 while viewing Zone Setup screen will display the following screen: ZONE TO DISABLE Disable Screen A flashing cursor appears to the right of the Z. To disable a zone, enter the three digit zone number (000 - 099). After the second digit is entered, the zone will be disabled and the cursor will return to the original position.

  • Page 108: Section 4: Operating Instructions

    Section 4: Operating Instructions 4.1 Panel Control Buttons 4.1.1 Acknowledge The first press of the Acknowledge key silences the piezo sounder, changes flashing LEDs to steady, and also changes the status field on the LCD display from capital letters to small letters. When the piezo is silenced, an acknowledge message is sent to the printer and the history file.

  • Page 109: Maintenance

    Normal Operation Operating Instructions Disabled This is a yellow LED that flashes to indicate that a zone, NAC, detector or module has been temporarily disabled in programming by the user. Maintenance This is a yellow LED that flashes to indicate that a smoke detector requires cleaning or replacement due to an invalid chamber reading or excessive drift.

  • Page 110: Alarm Operation

    Operating Instructions Alarm Operation <NOUN>; refers to the user programmed noun descriptor from library list resident in the control panel or custom entry via PC. • Third line in display: INVREP indicates an invalid reply from the addressable device. Other possible troubles include: –...

  • Page 111: Co Alarm Operation

    CO Alarm Operation Operating Instructions Time; the current time in this example is 10:00A which represents 10:00 AM Date; the current month, day and year in this example is 01 for January, 08 for the 8th day of the month and 16 for the year 2016 Device Address;...

  • Page 112: Process Monitor Operation

    Operating Instructions Process Monitor Operation Note that, like alarms, supervisory signals latch (except when programmed for supervisory autoresettable) and can be assigned to software zones. Supervisory alarms do not cause resound as do other alarm conditions. Open circuits in supervisory wiring are processed by the con- trol panel the same way as other trouble conditions.

  • Page 113: Mass Notification Operation

    Mass Notification Operation Operating Instructions 4.11 Mass Notification Operation The FACP may be installed with an NFC-50/100 audio system to provide mass notification operation. The FACP must control the NFC- 50/100 via the ANN-BUS. Refer to “Automatic Audio Panel Control” on page 46 for details and wiring information. Some mass notification installations may require that the activation of the audio system results in an override of an active fire notification at the FACP.

  • Page 114: Time Functions: Real-Time Clock

    Operating Instructions Time Functions: Real-Time Clock 4.17 Time Functions: Real-Time Clock The NFW-100X includes a crystal-based clock that provides time of day, date and day of week. Time is displayed as 12 or 24 hour time with month/day/year and is stored in RAM. Daylight savings time change-over is programmable and automatic. If both AC and battery are lost, the time must be reset.

  • Page 115: Special System Timers

    Special System Timers Operating Instructions second alarm occurring anytime during either time delay will cause immediate activation of all associated outputs PAS operation requires the approval of the local Authority Having Jurisdiction. Note that the PAS BYPASS monitor type code, when activated, will inhibit the PAS capability until the PAS BYPASS monitor is deactivated. While PAS is inhibited, signaling devices will immediately place the control panel into alarm.

  • Page 116: Walktest

    Operating Instructions Walktest 4.23 Walktest Walktest is a feature which allows one person to test the fire alarm system. An audible walktest will momentarily sound the Notification Appliance Circuits in the building and store the walktest information in a file at the panel. A silent walktest will not sound the NACs but will store the walktest information in a file which can be viewed at the panel.

  • Page 117: 2=Zones

    Read Status Operating Instructions Entering the three digit detector address will cause the control panel to display the current status of the selected device. For example, if a detector with address 001 on the SLC loop is entered, a display similar to the following will appear: NORMAL SMOKE(PHOTO) NORTH CLASSROOM Z005...

  • Page 118: 4: Timers

    Operating Instructions Read Status 4.24.4 Timers Pressing 2 while viewing Read Status Screen #2 will cause the following Timer screens to be displayed: TIMERS TIMERS PAS DELAY AC LOSS DELAY PRE SIGNAL CON MOD DLY WATERFLOW These screens will indicate the delay time, in seconds, for each of the first three and last possible delay options. The AC Loss Delay time is displayed in hours.

  • Page 119: 8: History

    Read Status Operating Instructions 4.24.8 History Pressing 3 while viewing Read Status Screen #3 will display the following screen: HISTORY 1=VIEW ALL 2=VIEW ALARMS 3=VIEW OTHER EVENTS The operator can view all events which have been stored in the history file, only alarms or other events, such as troubles or supervisories, by pressing the corresponding number key.

  • Page 120: 11: Print

    Operating Instructions Read Status Pressing 2 for POTS Settings while viewing Communicator Screen #1 will display settings for the telephone portion of the Communicator. POTS SETTINGS 1=LINE 1 2=LINE 2 3=GAINS Pressing 1 or 2 will display whether each phone line is enabled Yes or disabled No, whether the phone type is touchtone or rotary, and whether the phone line is being supervised Yes or No.

  • Page 121: Chamber Value

    Read Status Operating Instructions Pressing 1 while viewing Print Screen #2 allows the user to print the detector data for each addressable smoke detector connected to the sys- tem. A printout, similar to the following example, will be generated if an optional printer is connected to the FACP. DEVICE # DEVICE TYPE % DRIFT COMP...

  • Page 122: 12: Time-Date

    Operating Instructions Read Status Figure 4.1 illustrates a graphic representation of the maintenance levels: DIRTY Maintenance Urgent Maintenance Alert Acceptable Range Low Chamber Reading VALUE Figure 4.1 Diagram of Maintenance Levels Pressing 2 while viewing Print Screen #2 allows the user to print the Communicator’s settings. Refer to “Com- PRINT municator”...

  • Page 123: Section 5: Central Station Communications - Pots Transmission

    Section 5: Central Station Communications - POTS Transmission The control panel transmits zone and system status reports to Central Stations via the public switched telephone network. Two supervised telephone line connections are made to interface the control panel to the telephone lines. Two optional 7 foot telephone cords are available for this purpose and can be purchased separately.
  • Page 124 Central Station Communications - POTS Transmission Transmittal Priorities Red LEDs are provided on the circuit board to identify which telephone line is activated. Also, a green LED labeled Kissoff will turn on whenever the control panel has successfully transmitted reports to the Central Station. The Kissoff LED may turn on several times during communications with a Central Station.

  • Page 125: Section 6: Fs-Tools Upload/Download

    Section 6: FS-Tools Upload/Download Important! The FACP will automatically reset 2 minutes after completion of a user program download via the FS-Tools programming util- ity. To prevent program corruption, the operator must wait until this panel reset occurs before performing any panel operations. The control panel may be programmed or interrogated off-site via an Ethernet connection or locally using a USB cable.

  • Page 126: 1: Security Features

    FS-Tools Upload/Download Transferring a Program There cannot be any active communications ongoing with a Central Station receiver All active events must be successfully 'kissed-off' by the Central Station(s). The communicator must be in a standby state with no new information waiting to be transmitted to a Central Station 6.2.1 Security Features Upload and download with the control panel have been carefully designed to include key security features to ensure proper functionality.

  • Page 127: Section 7: Usb Upload/Download

    Section 7: USB Upload/Download Important! The FACP will automatically reset 2 minutes after completion of a user program download. To prevent program corruption, the operator must wait until this panel reset occurs before performing any panel operations. CAUTION: After successfully downloading a program, make certain to perform the following steps: Print out all programmed data via Print Mode or manually view programmed entries and compare to intended program data Test all affected panel operations Immediately correct any problems found...
  • Page 128 USB Upload/Download USB Upload/Download Pressing 2 for Yes will cause the following screen to be displayed: USB UP/DOWNLOAD SYSTEM CONFIGURATION TRANSFER IN PROCESS PLEASE WAIT An error message will display if there is no USB drive inserted in the FACP or if there is no existing configuration saved on the USB drive. While this screen is displayed, local programming downloads are allowed.

  • Page 129: Section 8: Firmware Upgrade

    Section 8: Firmware Upgrade In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that you download the most current version of software for each product from www.notifier.com prior to commissioning any system.

  • Page 130: Section 9: Power Supply Calculations

    Section 9: Power Supply Calculations 9.1 Overview This section contains instructions and tables for calculating power supply currents in alarm and standby conditions. This is a four-step pro- cess, consisting of the following: Calculating the total amount of AC branch circuit current required to operate the system Calculating the worst-case system current load on the control panel, when primary (AC) power is applied, to assure that the limit of the its internal power supply will not be exceeded.
  • Page 131 Calculating the System Current Load Power Supply Calculations Calculation Column 1 Calculation Column 2 Calculation Column 3 Device Type Primary (AC) Power Source Secondary (Battery) Power Source Secondary (Battery) Power Source Fire Alarm Current (amps) Fire Alarm Current (amps) Standby Current (amps) X[current draw]= Total X [current draw]=...

  • Page 132: Calculating The Battery Size

    Power Supply Calculations Calculating the Battery Size When AC power is initially applied to the panel and the battery is not fully charged, an initial charge current of up to 5.3 amps may be observed at the battery. This high current is only applied for a very short duration (milliseconds) and does not affect system load or battery size calculations. 10 Total Standby current load cannot exceed 2.25 amps.

  • Page 133: Appendix A: Software Zones

    Appendix A: Software Zones A.1 Correlations Setup and configuration of an addressable system is different than a conventional system. In a conventional system, assignment of input devices (smoke detectors, pull stations, heat detectors, etc.) to zones is accomplished through wiring. The wiring is direct from clearly marked panel terminals to any device assigned to a particular zone.
  • Page 134 Software Zones Correlations Correlation of Input and Output Zones Input Devices Zones Output Devices smoke control smoke control ZONE monitor control monitor control control monitor control smoke ZONE control smoke smoke control smoke ZONE smoke control monitor NFW-100X Manual — P/N LS10131-001NF-E:F 6/7/2022...
  • Page 135 Correlations Software Zones The zone correlations which are shown graphically above are also presented in Table A.1 on page 135 and Table A.2 on page 136. DETECTOR ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN smoke FIRST HALL...
  • Page 136 Software Zones Correlations MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN monitor monitor 1, 2 monitor 1, 2 monitor control control control control control 1, 2, 3 control Table A.2 Module Programming Sheet Example NFW-100X Manual —...
  • Page 137 Correlations Software Zones DETECTOR ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN Table A.3 Blank Detector Programming Sheet NFW-100X Manual — P/N LS10131-001NF-E:F 6/7/2022...
  • Page 138 Software Zones Correlations MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Type Zone Number ADJ/NOUN Address Device Type Zone Number ADJ/NOUN Table A.4 Blank Module Programming Sheet NFW-100X Manual — P/N LS10131-001NF-E:F 6/7/2022...

  • Page 139: Appendix B: Default Programming

    Appendix B: Default Programming The following table provides a list of the programming options and their factory default settings. Program Option Factory Default Program Option Factory Default Detector Programming Not Installed Aux Power Class A Detector Type Smoke-Photo Aux Power Resettable Detector Verification Aux Power 2 Resettable Detector Walktest...

  • Page 140: Appendix C: Nfpa Standard-Specific Requirements

    Appendix C: NFPA Standard-Specific Requirements The NFW-100X has been designed for use in commercial, industrial, and institutional applications and meets the requirements for service under the National Fire Protection Association (NFPA) Standards outlined in this Appendix. The minimum system components required for compliance with the appropriate NFPA standard are listed below: NFW-100X Control Panel...
  • Page 141 NFPA Standard-Specific Requirements NFPA 72 Remote Station Protective Signaling System Notes: Enable 4XTM supervision in FACP System Setup programming. Refer to page 83 for more information. Refer to “4XTM Transmitter Module Installation” on page 31 for detailed information. RS82 Remote Station Receiver UL listed. Refer to Instruction Manual for Remote Station Receiver Model RS82.
  • Page 142 NFPA Standard-Specific Requirements NFPA 72 Proprietary Protective Signaling Systems NFW-100X Addressable Fire Control Panel NFW-100X Main Board Form-C Alarm contact programmed to activate on General Alarm. Form-C Trouble contact which will automatically activate on any Trouble condition. Form-C relay contact programmed to activate on Supervisory condition.

  • Page 143: C.1: Mbt-1 Municipal Box Trip - Silenceable

    MBT-1 Municipal Box Trip - Silenceable NFPA Standard-Specific Requirements C.1 MBT-1 Municipal Box Trip - Silenceable The following figure illustrates the connection of the MBT-1 (Municipal Box Trip) between the FACP and a Local Energy Municipal Box. The use of an addressable control module programmed for General Alarm and Silenceable allows silencing of the Municipal Box without resetting the panel or box.

  • Page 144: Appendix D: Wire Requirements

    Appendix D: Wire Requirements T-tapping of the SLC loop wiring is allowed for 2-wire (Class B) configurations. The total resistance of any branch cannot exceed 40 ohms. The total wire length of all branches cannot exceed 10,000 feet (3,000 m). Connecting external system accessories to the NFW-100X main circuits must be carefully considered to ensure proper operation.

  • Page 145: D.1: Nac Wiring

    NAC Wiring Wire Requirements D.1 NAC Wiring The following table lists NAC wiring requirements for the FACP. CLASS-B CLASS-A Max. Max. allowable wire pair length Max. allowable wire pair length allowable NAC Load (feet) (feet) total loop (Amps) resistance AWG 12 AWG 14 AWG 16 AWG 18...

  • Page 146: Appendix E: Hvac Control

    Appendix E: HVAC Control The FACP can be programmed to shut down a building’s HVAC fans in the event of a fire. The fans cannot be restarted until the fire alarm condition has been cleared and the FACP has been reset to a normal (non-alarm) condition. IMPORTANT! This HVAC feature is not to be used for smoke control.

  • Page 147: E.2: Monitor Module Operation

    Monitor Module Operation HVAC Control E.2 Monitor Module Operation E.2.1 HVAC RESTART The HVAC RESTART type code can be assigned to any addressable monitor module for the purpose of resetting (deactivating) the HVAC SHUTDN control module and turning the fans back on. The HVAC RESTART monitor module acts globally throughout the FACP system and therefore is not programmed to a particular software zone.

  • Page 148: Appendix F: Ademco Contact Id Format Event Code Descriptions

    Appendix F: Ademco Contact ID Format Event Code Descriptions This appendix describes the various Event Codes and their messages which are available for the Ademco Contact ID Format. F.1 Transmission Format Between DACT and Receiver The transmission string for the Ademco Contact ID Format is as follows: SSSS 18 QXYZ GG CCC where SSSS...
  • Page 149 Ademco Contact ID Typical Printout Ademco Contact ID Format Event Code Descriptions EVENT CODE CLASSIFICATIONS ALARMS SUPERVISORY TROUBLES OPEN/CLOSE DISABLES/BY TEST/MISC. REMOTE ACCESS PASSES Medical Fire System Open/Close System Test Fire Sounder/Relay Remote Access Sounder/Relay Panic System Peripheral Access Control System Peripheral Burglary Communication...
  • Page 150 Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Typical Printout EVENT MESSAGE 24-Hour Non-Burglary - 150 and 160 150 24-Hour Non-Burg ALARM - 24-Hr. Non-Burg - # 151 Gas detected ALARM - Gas Detected - # 152 Refrigeration ALARM - Refrigeration - # 153 Loss of heat ALARM - Heating System - #...
  • Page 151 Ademco Contact ID Typical Printout Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE Communication Troubles - 350 and 360 350 Communication TROUBLE - Communication Trouble 351 Telco 1 fault TROUBLE - Phone Line #1 352 Telco 2 fault TROUBLE - Phone Line #2 353 Long range radio transmitter fault TROUBLE - Radio Transmitter 354 Fail to communicate...
  • Page 152 Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Typical Printout EVENT MESSAGE 527 Bell 4 disable DISABLE - Bell/Siren - #4 System Peripheral Disables - 530 and 540 Communication Disables - 550 and 560 551 Dialer disabled DISABLE - Dialer Disable 552 Radio transmitter disabled DISABLE - Radio Disable Bypasses - 570...

  • Page 153: Appendix G: Central Station Points

    Appendix G: Central Station Points The control panel transmits Central Station Reports in a numerical format which indicates the FACP addressable device address that is reporting. The following table indicates the Central Station Report (CS Report) number that will be transmitted and the addressable device address it represents.
  • Page 154 Central Station Points Module Module Module Module Report Address Report Address Report Address Report Address Table G.2 Addressable MODULES NFW-100X Manual — P/N LS10131-001NF-E:F 6/7/2022...

  • Page 155: Appendix H: Nfpa Requirements

    Appendix H: NFPA Requirements The following is the minimum configuration to meet the NFPA requirements. Process Module Local Proprietary Management NFW-100X IPOTS-COM (pre-installed communicator) 4XTM DP-ES-R or DP-ES-B NFS-LBB N-ANN-LED N-ANN-80 N-ANN-100 N-ANN-S/PG N-ANN-I/O N-ANN-RLED N-ANN-RLY Where Y = Yes, N = No, and O = Optional Non-Emergency Not available on the NFW-100XI One of the indicated modules is required when the IPOTS-COM is not employed.

  • Page 156: Appendix I: Open/Short/Ground Trip Values

    Appendix I: Open/Short/Ground Trip Values Table I.1 lists the earth fault resistance detection for each applicable terminal on the FACP. Output Circuit Terminal Trip Resistance (in ohms) Remote Sync 360K Remote Sync 330K NAC 1-2 360K NAC 1-2 320K ANN Bus 270K ANN Bus 265K...

  • Page 157: Index

    Index Numerics auxiliary power 14 settings 84 control buttons 108 24 hour test time 87 control module 17 24VDC power 73 auto silence 77 4XTM module 140 backbox 17 description display 69 coil resistance 31 see also cabinet 23 display 66 current 31 banner 73 edit 66...
  • Page 158 Index disable battery charger 73 gains 85 maintenance alert 13 charger 73 gateway IP address 85 levels 121 zone 70 general alarm zone Maintenance Program Level 49 disable point see also zone Z000 59 maintenance program level 2 103 maintenance level 103 ground fault 45 maintenance programming 52 download 125...
  • Page 159 Index N-ANN-80 annunciator module 14 password 13 exiting 49 N-ANN-I/O LED driver 14 change 50 factory default 139 N-ANN-LED annunciator module 14 invalid 52 manual 49 N-ANN-RLED annunciator module 14 maintenance level 2 103 modules 61 N-ANN-RLY relay module 14 password change off-line computer 49 N-ANN-S/PG printer module 14...
  • Page 160 Index security features 126 maintenance level 105 nonsilenceable 71 sensitivity 113 system point 116 silenceable 72 see also smoke detector sensitivity 113 system setup 72 waterflow delay timer 76 signal rate 13 waterflow retard Timer 115 signaling line circuit waterflow silenceable 73 see also SLC 14 wire requirements 144 telephone circuitry 20...

  • Page 161: Slide-In Labels

    Slide-in Labels Carefully cut along the outside of each label. Identify Function (F1-F4) keys as desired and slide the labels into the keypad. Starting at the center of the keypad next to the Function Keys, slide each label into the groove towards the outer edge. Slide-in Labels NFW-100X Manual —...
  • Page 162 NFW-100X Manual — P/N LS10131-001NF-E:F 6/7/2022...

  • Page 163: Nfw-100X Series Fire Alarm Control Panel Operating Instructions

    NFW-100X Series Fire Alarm Control Panel Operating Instructions NORMAL - Only AC POWER is illuminated green. PANEL KEY - The key to open the panel can be found at the following All other indicators are off. LCD display will read SYSTEM ALL location: NORMAL.

  • Page 165: Manufacturer Warranties And Limitation Of Liability

    Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan.
  • Page 166 NOTIFIER 12 Clintonville Road Northford, CT 06472-1610 USA 203-484-7161 www.notifier.com...

This manual is also suitable for:

Notifier nfw-100x

Table of Contents