Page 1
Installations- und Bedienungsanleitung Installation instruction and operating manual Fußbodenheizungsaktor – S. 2 6-fach, 230 V Floor Heating Actuator – p. 44 6 channels, 230 V HmIP-FAL230-C6...
Anlernen ................20 6.4.1 Anlernen an den Homematic IP Wandthermostaten ..........20 6.4.2 Anlernen an die Homematic IP Multi IO Box ... 22 6.4.3 Einen weiteren Fußbodenheizungsaktor hinzufügen .............. 22 6.4.4 Anlernen an den Homematic IP Access Point . 24 Konfiguration über den Homematic IP...
Page 8
10.2 Duty Cycle ................36 10.3 Fehlercodes und Blinkfolgen ..........37 10.3.1 Blinkfolgen der System-LED (A) ......37 10.3.2 Blinkfolgen der Kanal-LED ........39 Wiederherstellung der Werkseinstellungen ..... 40 12 Wartung und Reinigung ..........40 13 Allgemeine Hinweise zum Funkbetrieb .....41 14 Technische Daten ............42...
Hinweise zur Anleitung Hinweise zur Anleitung Lesen Sie diese Anleitung sorgfältig, bevor Sie Ihr Home- matic IP Gerät in Betrieb nehmen. Bewahren Sie die An- leitung zum späteren Nachschlagen auf! Wenn Sie das Gerät anderen Personen zur Nutzung über- lassen, übergeben Sie auch diese Anleitung. Benutzte Symbole: Achtung! Hier wird auf eine Gefahr hingewiesen.
Page 10
Gefahrenhinweise Betreiben Sie das Gerät nur in trockener sowie staubfreier Umgebung, setzen Sie es keinem Ein- fluss von Feuchtigkeit, Vibrationen, ständiger Sonnen- oder anderer Wärmeeinstrahlung, Kälte und keinen mechanischen Belastungen aus. Das Gerät ist kein Spielzeug! Erlauben Sie Kindern nicht damit zu spielen. Lassen Sie das Verpa- ckungsmaterial nicht achtlos...
Page 11
Gefahrenhinweise Arbeiten am 230-V-Netz dürfen nur von einer Elektrofachkraft (nach VDE 0100) erfolgen. Dabei sind die geltenden Unfallverhütungsvorschriften zu beachten. Zur Vermeidung eines elektrischen Schlages am Gerät, schalten Sie bitte die Netz- spannung frei (Sicherungsautomat abschalten). Bei Nichtbeachtung der Installationshinweise können Brand oder andere Gefahren entstehen.
Mit dem Homematic IP Fußbodenheizungsaktor können Sie Ihre Fußbodenheizung Raum für Raum komfortabel und bedarfsgerecht per Smartphone App oder mit dem Homematic IP Wandthermostaten steuern und so die Raumtemperatur auf Ihre individuellen Bedürfnisse an- passen. Der Fußbodenheizungsaktor kann zur Steuerung einer Fußbodenheizung mit bis zu 6 Heizzonen/9 Heizkreise...
Page 13
Sie können das Gerät flexibel mit den mitgelieferten Schrauben oder einfach auf einer Hutschiene montie- ren. Dank der sicheren Funkkommunikation zwischen den Homematic IP Geräten beschränkt sich der Verdrah- tungsaufwand auf ein Minimum. Geräteübersicht (s. Abbildung 1): Systemtaste (Anlerntaste und LED) Selecttaste (Kanaltaste und LED) Öffnungsschlitz...
Allgemeine Systeminformationen Allgemeine Systeminformationen Dieses Gerät ist Teil des Smart-Home-Systems Homema- tic IP und kommuniziert über das Homematic IP Funk- protokoll. Alle Homematic IP Geräte können komfortabel und individuell per Smartphone über die Homematic IP App konfiguriert werden. Welcher Funktionsumfang sich...
Montage • Zeichnen Sie zwei der Bohrlöcher im Anstand von 13,6 cm mit einem Stift an der Wand an (s. Abbildung 3). • Bohren Sie die vorgezeichneten Löcher mit ei- nem geeigneten Bohrer. • Montieren Sie den Fußbodenheizungsaktor durch Eindrehen der mitgelieferten Dübel und Schrau- ben (s.
Inbetriebnahme Inbetriebnahme Installationshinweise Bitte lesen Sie diesen Abschnitt erst vollständig, bevor Sie mit der Installation beginnen. Hinweis! Installation nur durch Personen mit einschlägigen elektrotechnischen Kenntnissen und Erfahrungen!* Durch eine unsachgemäße Installation gefährden Sie • Ihr eigenes Leben; • das Leben der Nutzer der elektrischen Anlage. Mit einer unsachgemäßen Installation riskieren Sie schwere Sachschäden, z.
Page 17
Inbetriebnahme der Abschaltbedingungen; • IP-Schutzarten; • Einbau des Elektroinstallationsmaterials; • Art des Versorgungsnetzes (TN-System, IT-System, TT-System) und die daraus folgenden Anschlussbedingungen (klassische Nullung, Schutzerdung, erforderliche Zusatzmaßnahmen etc.). Für den Einbau des Fußbodenheizungsaktos in ei- nen Stromkreisverteiler, muss das Gerät entspre- chend VDE 0603, DIN 43871 (Niederspannungs- unterverteilung (NSUV)), DIN 18015-x eingebaut werden.
Inbetriebnahme Zugelassene Leitungsquerschnitte zum Anschluss an die Anschlussklemmen des Fußbodenheizungsaktors sind: Starre Leitung [mm Flexible Leitung mit und ohne Aderendhülse [mm 0,75 – 1,50 0,75 – 1,50 Installation Für die Installation des Fußbodenheizungsaktors gehen Sie wie folgt vor: • Öffnen Sie die Abdeckung (D), indem Sie die Ver- rastung unter dem Öffnungsschlitz (C) mit einem geeigneten Schraubendreher eindrücken und die Abdeckung nach oben abziehen (s.
Inbetriebnahme be der Heizkreise an die Anschlussklemmen (H-I) oder eine Umwälzpumpe an die Anschlussklem- men (H) an. • Achten Sie vor dem Verschließen der Abdeckung darauf, dass alle Anschlussleitungen ordnungs- gemäß in die vorgesehenen Kabelführungen ge- drückt sind. • Schließen Sie die Abdeckung wieder, indem Sie die Rastnasen der Abdeckung in die vorgesehenen Öffnungen schieben und die Abdeckung herunter- drücken.
Sie können den Fußbodenheizungsaktor entweder direkt an Homematic IP Geräte (wie bspw. an den Wandthermo- staten oder an die Multi IO Box) oder an den Homematic IP Access Point anlernen. Beim direkten Anlernen erfolgt die Konfiguration am Wandthermostaten und beim Anlernen an den Access Point über die Homematic IP App.
Page 21
Inbetriebnahme Sie können den Anlernvorgang durch erneute kurze Betätigung der Systemtaste (A) abbrechen. Dies wird durch ein rotes Aufleuchten der LED (A) bestätigt. Wenn kein Anlernen erfolgt, wird der Anlernmo- dus automatisch nach 3 Minuten beendet. Wenn Sie den Fußbodenheizungsaktor an einen Home- matic ...
War der Anlernvorgang nicht erfolgreich, leuchtet die LED (A) rot auf. Versuchen Sie es erneut. 6.4.2 Anlernen an die Homematic IP Multi IO Box Wenn Sie den Fußbodenheizungsaktor an eine Homema- tic IP Multi IO Box anlernen möchten, müssen die beiden zu verknüpfenden Geräte in den Anlernmodus gebracht...
Page 23
Versuchen Sie es erneut. • Lernen Sie den neuen Fußbodenheizungsaktor ggf. an weitere Homematic IP Geräte, wie z. B. an einen Wandthermostaten oder eine Multi IO Box, an, indem Sie zunächst den Fußbodenheizungs- aktor und dann das anzulernende Gerät in den Anlernmodus versetzen.
6.4.4 Anlernen an den Homematic IP Access Point Richten Sie zunächst Ihren Homematic IP Access Point über die Homematic IP App ein, um weitere Homematic IP Geräte im System nutzen zu kön- nen. Ausführliche Informationen dazu finden Sie in der Bedienungsanleitung des Access Points.
Page 25
Inbetriebnahme matic IP App. • Zur Bestätigung geben Sie in der App die letzten vier Ziffern der Gerätenummer (SGTIN) ein oder scannen Sie den QR-Code. Die Gerätenummer finden Sie auf dem Aufkleber im Lieferumfang oder direkt am Gerät. • Warten Sie, bis der Anlernvorgang abgeschlossen ist.
Konfiguration über den Homema- tic IP Wandthermostaten Die Konfiguration des Homematic IP Fußboden- heizungsaktors ist mit dem Homematic IP Wand- thermostaten (HmIP-WTH-2), über den Home- matic IP Access Point in Verbindung mit der Smartphone App oder über die WebUI der Homematic Zentrale CCU2 möglich.
Page 27
Konfiguration über den Homematic IP Wandthermostaten • Stellen Sie Vor- sowie Nachlaufzeiten der Pumpe, Eco-Temperaturen, Zeitintervalle etc. ganz indivi- duell nach dem folgenden Schema ein. Geräteparameter UnP1: Parame- Index Wert Bedeutung Frost- P024 Frostschutz inaktiv schutz- 2,0 °C tempe- 2,5 °C ratur 8,0 °C (default)
Page 28
Konfiguration über den Homematic IP Wandthermostaten Pumpensteuerung aktiv *4 Pumpen- P025 steue- Lastausgleich rung Pumpensteuerung aktiv *4 aktiv/ inaktiv, Lastausgleich Pumpensteuerung aktiv *4 Lastaus- gleich *1 / Lastsammlung Last- Pumpensteuerung aktiv *4 samm- lung *2 Lastsammlung Antriebs- Pumpensteuerung inaktiv (default)
Page 29
Konfiguration über den Homematic IP Wandthermostaten Notbe- P026 trieb im Heizmo- … 25 % (default) … 99 % 100 % Notbe- P032 0 % (default) trieb im Kühlmo- … … 99 % 100 % *1: Heizzonen werden (wenn möglich) gestaffelt ge- steuert.
Page 30
Konfiguration über den Homematic IP Wandthermostaten Geräteparameter UnP2: Parameter Index Wert Bedeutung Ventilschutz- P007 0 Minuten Funktions- 1 Minute Dauer 5 Minuten (default) 10 Minuten Ventilschutz- P051 0 Tage Funktions- 1 Tag Intervallzeit 14 Tage (default) 27 Tage 28 Tage...
Page 31
Konfiguration über den Homematic IP Wandthermostaten Kanalparameter ChAn: Parameter Index Wert Bedeutung Einschalt- P006 0 Minuten verzöge- 1 Minute rung der 2 Minuten (default) Pumpe (nur für 19 Minuten Kanal 1 20 Minuten verfügbar) Dauer/ P007 0 Minuten Länge der...
Page 32
Konfiguration über den Homematic IP Wandthermostaten Minimale P045 5.0 °C Fußbo- 5.5 °C dentem- 19.0 °C (default) peratur in Verbin- dung mit 29.5°C einem 30.0°C Fußbo- den-Tem- peratur- sensor Luftfeuch- P050 40 %; Luftfeuchtigkeits- tigkeits- grenze inaktiv grenze … …...
Page 33
Konfiguration über den Homematic IP Wandthermostaten Zeitinter- P051 1 Tag vall für die 2 Tage Pumpen- 14 Tage (default) schutz- funktion (nur für 27 Tage Kanal 1 28 Tage verfügbar) Kühlen im P052 Kühlen im Kühlmodus Kühlmo- inaktiv dus aktiv/ Kühlen im Kühlmodus...
Manuelle Bedienung Manuelle Bedienung Heizzonen ein- bzw. ausschalten Zu Installations- und Testzwecken können die einzelnen Heizzonen manuell ein- bzw. ausgeschaltet werden. Um eine Heizzone manuell ein- bzw. auszuschalten, gehen Sie wie folgt vor: • Wählen Sie mit der Selecttaste (B) den gewünsch- ten Kanal aus (s.
Geräteverknüpfungen löschen • Wollen Sie keine Änderung des Parameters vor- nehmen, können Sie das Menü über einen kurzen Tastendruck der Selecttaste (B) verlassen. • Um den Parameter von aktiv auf inaktiv bzw. von inaktiv auf aktiv umzustellen, drücken Sie für mind.
Stunde (also 36 Sekunden in einer Stunde). Die Geräte dürfen bei Erreichen des 1-%-Limits nicht mehr senden, bis diese zeitliche Begrenzung vorüber ist. Gemäß dieser Richtlinie, werden Homematic IP Geräte zu 100 % nor- menkonform entwickelt und produziert. Im normalen Betrieb wird der Duty Cycle in der Regel nicht erreicht.
Fehlerbehebung vermehrte und funkintensive Anlernprozesse der Fall sein. Eine Überschreitung des Duty-Cycle-Limits wird durch dreimal langes rotes Blinken der LED angezeigt und kann sich durch temporär fehlende Funktion des Gerätes äu- ßern. Nach kurzer Zeit (max. 1 Stunde) ist die Funktion des Gerätes wiederhergestellt.
Page 38
Fehlerbehebung Kurzes Anlernmodus aktiv Geben Sie die oranges letzten vier Ziffern Blinken (alle der Geräte- 10 s) Seriennummer zur Bestätigung ein (s. „6.4 Teaching-in“ auf Seite 58). 1x langes Vorgang Versuchen Sie es rotes fehlgeschlagen erneut („10.1 Befehl Leuchten oder Duty-Cycle- nicht bestätigt“...
Fehlerbehebung 10.3.2 Blinkfolgen der Kanal-LED Blinkcode Bedeutung Lösung Langsames Notbetrieb aktiv Batterien des Blinken Wandthermostaten wechseln, Funktest durchführen, Wandthermostat ggf. neu positio- nieren, defekten Wandthermostaten austauschen Doppeltes, Funkverbindung Position des kurzes zum Wandther- Wandthermostaten Blinken mostaten gestört verändern oder einen Repeater einsetzen.
Lassen Sie die Systemtaste wieder los, um das Wiederherstellen der Werkseinstellungen abzu- schließen. Das Gerät führt einen Neustart durch. Nach dem Neustart können Sie das Gerät wieder in Ihr Homematic IP System integrieren. Wartung und Reinigung Das Gerät ist wartungsfrei. Überlassen Sie eine War-...
Allgemeine Hinweise zum Funkbetrieb Reinigen Sie das Gerät mit einem weichen, sauberen, trockenen und fusselfreien Tuch. Verwenden Sie keine lösemittelhaltigen Reinigungsmittel, das Kunststoffge- häuse und die Beschriftung können dadurch angegriffen werden. Allgemeine Hinweise zum Funk- betrieb Die Funk-Übertragung wird auf einem nicht exklusiven Übertragungsweg realisiert, weshalb Störungen nicht ausgeschlossen werden können.
Technische Daten Technische Daten Geräte-Kurzbezeichnung: HmIP-FAL230-C6 Konstruktion des Regel- und Steuergerätes (RS): Unabhängig montiertes elektro-nisches RS für Aufbaumontage Anzahl Heizzonen: Anzahl Antriebe: 9 / (8) Anzahl Pumpen: Versorgungsspannung: 230 V/50 Hz Stromaufnahme: 6,3 A max. Schaltleistung je Heizzone: 1 A max.
Page 43
Technische Daten Temperatur Glühdrahtprüfung: 850 °C Temperatur Kugeldruckprüfung: 125 °C PTI-Wert des Gehäusematerials: IIIb mit 100 < CTI < 175 Abmessungen (B x H x T ): 225 x 75 x 52 mm Gewicht: 566 g Funkfrequenz: 868,3 MHz / 869,525 Empfängerkategorie: SRD category 2 Typ.
Page 45
Teaching-in ................58 6.4.1 Pairing with a Homematic IP Wall Thermostat 58 6.4.2 Pairing with a Homematic IP Multi IO Box ..59 6.4.3 Adding a new floor heating actuator ....60 6.4.4 Teaching-in to the Homematic IP Access Point .............61 Configuration via the Homematic IP Wall Thermostat .............63...
Page 46
10.3 Error codes and flashing sequences .......74 10.3.1 Flashing sequences of the system LED (A) ..74 10.3.2 Flashing sequences of the channel LED ....76 Restore factory settings ..........77 12 Maintenance and cleaning ...........78 13 General information about radio operation .....78 14 Technical specifications ..........79...
Information about this manual Please read this manual carefully before beginning op- eration with your Homematic IP component. Keep the manual so you can refer to it at a later date if you need to. If you hand over the device to other persons for use, please hand over this manual as well.
Page 48
Hazard information The device may only be operated in dry and dust- free environment and must be protected from the effects of moisture, vibrations, solar or other meth- ods of heat radiation, cold and mechanical loads. The device is not a toy; do not allow children to play with it.
Page 49
Hazard information accident prevention regulations must complied with whilst such work is being carried out. To avoid electric shocks from the device, please disconnect the mains voltage (trip the miniature circuit-breaker). Noncompliance with the installation instructions can cause fire or introduce other hazards.
The Homematic IP Floor Heating Actuator offers comfortable and demand-based room-by-room control of your floor heating system via smartphone app or the Homematic IP Wall Thermostat, according to your personal needs. The floor heating actuator can be used for controlling a floor heating system with up to 6 heating zones/9 heating circuits as well as a heating pump or circulation pump.
Page 51
Function and device overview between the Homematic IP devices, the wiring effort is kept to a minimum. Device overview (see fig. 1): System button (teach-in/pairing button and LED) Select button (channel button and LED) Slot for opening Cover Spring latch for DIN rail mounting...
General system information General system information This device is part of the Homematic IP smart home sys- tem and works with the Homematic IP radio protocol. All Homematic IP devices can be configured comfortably and individually with a smartphone via the Homematic IP app.
Start-up • Use an appropriate drill to make the holes as il- lustrated. • Use the supplied screws and plugs to fasten the floor heating actuator (see fig. 3). DIN rail mount For mounting the floor heating actuator to a DIN rail, please proceed as follows: •...
Page 54
Start-up • and the lives of other users of the electrical sys- tem. Incorrect installation also means that you are running the risk of serious damage to property, e.g. because of a fire. You may be personally liable in the event of injuries or damage to property.
Page 55
Start-up voltage sub-distribution board), DIN 18015-x. In this case, the installation must be made on a mounting rail (DIN rail) according to EN50022. Installation and wiring have to be performed according to VDE 0100 (VDE 0100-410, VDE 0100-510 etc.). Please consider the technical connection requirements (TAB) of your energy supplier.
Start-up Installation To install the floor heating actuator, please proceed as follows: Open the cover (D). Therefore, release the catch • under the slot for opening (C) by pushing it with a screwdriver. Remove the cover by pulling it up- wards (see fig.
Start-up Behaviour after switching on the mains voltage After switching on the mains voltage, the LED (B) lights permanently green. If the device has not yet been connected, teach-in mode will be activated during the first 3 minutes after the mains voltage has been switched on.
You can either pair the floor heating actuator directly with other Homematic IP devices (e.g. the wall thermostat or the Multi IO Box) or teach it in to the Homematic IP Access Point. After pairing, the device is configured at the wall thermostat.
Pairing with a Homematic IP Multi IO Box If you want to pair the floor heating actuator with a Homematic IP Multi IO Box, the pairing mode of both devices has to be activated first. To do this, proceed as...
Start-up seconds until the LED quickly starts flashing or- ange (see fig. 7). Pairing mode remains activated for 3 minutes. • Press and hold down the system button of the Multi IO Box for at least 4 seconds to activate the pairing mode.
6.4.4 Teaching-in to the Homematic IP Access Point First set up your Homematic IP Access Point via the Homematic IP app to enable operation of other Homematic IP devices within your system. For further information, please refer to the operating manual of the Access Point.
Page 62
3 minutes by pressing the system button (A) briefly (see fig. 7). • Your device will automatically appear in the Homematic IP app. • To confirm, please enter the last four digits of the device number (SGTIN) in your app or scan the QR code.
Configuration via the Homematic IP Wall Thermostat Configuration via the Homematic IP Wall Thermostat The Homematic IP Floor Heating Actuator can be configured via the Homematic IP Wall Thermo- stat (HmIP-WTH-2), via the Homematic IP Access Point together with the smartphone app or via the WebUI of the Homematic Central Control Unit CCU2.
Page 64
Configuration via the Homematic IP Wall Thermostat All the settings that are made under “UnP1/UnP2” will be applied to the entire device. All settings that are made under “ChAn” will be applied to the single channels of the device. •...
Page 65
Configuration via the Homematic IP Wall Thermostat Pump control activated *4 Pump P025 control Load balancing activated/ Pump control activated *4 deactiva- ted, Load balancing Pump control activated *4 Load ba- lancing *1 / Load collection Load Pump control activated *4...
Page 66
Configuration via the Homematic IP Wall Thermostat Emer- P026 gency operation … 25 % (default) in heating mode … 99 % 100 % Emer- 0 % (default) P032 gency operating … … in cooling 99 % mode 100 % *1: Heating zones will be controlled in a staggered way...
Page 67
Configuration via the Homematic IP Wall Thermostat Device parameter UnP2: Parameter Index Value Meaning Duration P007 0 minutes of valve 1 minute protection function 5 minutes (default) 10 minutes Invertal P051 0 days time for 1 day valve protection 14 days (default)
Page 68
Configuration via the Homematic IP Wall Thermostat Duration P007 0 minutes of pump 1 minute (default) protection function 9 minutes (only for 10 minutes channel 1) Switch off P008 0 minutes delay for 1 minute 2 minutes (default) pump (only for...
Passive convector Active convector For further information regarding the configura- tion, please refer to the user manual of the Homematic IP Wall Thermostat (HmIP-WTH-2). Manual operation Switch heating zones on/off For installation and tests you can manually switch single heating zones on or off. To switch single heating zones on or off, please proceed as follows: •...
Manual operation The channel will be switched on or off for 15 minutes. Afterwards, normal operation will be continued for the heating zone. Activating/deactivating the pump control If you want to use connection terminal (H) for controlling a heating pump, the heating zone can be switched to pump control directly via the device.
Delete device connections Delete device connections To delete the device connections between the floor heat- ing actuator and the wall thermostat, please proceed as follows: • Select the channel of the floor heating actuator to which the wall thermostat is connected using the select button (B) (see fig.
Devices must cease transmission when they reach the 1% limit until this time restriction comes to an end. Homematic IP devices are designed and produced with 100% conformity to this regulation. During normal operation, the duty cycle is not usually reached.
Page 74
Troubleshooting Short orange Radio Wait until the flashing transmission/ transmission is attempting to completed. transmit/data transmission 1x long green Transmission You can continue lighting confirmed operation. 1x long red Transmission Please try again (s. lighting failed „10.1 Command not confirmed“ on page 72).
Troubleshooting 6x long red Device defective Please see your flashing app for error message or contact your retailer. 1x orange Test display Once the test dis- and 1 x green play has stopped, lighting you can continue. 10.3.2 Flashing sequences of the channel LED Flashing code Meaning Solution...
Page 76
Restore factory settings Slow Emergency op- Change batteries flashing eration activated of the wall ther- mostat, perform a communication test, re-posi- tion the wall thermostat (if required), replace wall thermostat if defective Short double Radio connec- Re-position wall flashing tion to wall ther- thermostat or mostat failed add a repeater...
• Release the system button to finish the proce- dure. The device will perform a restart. After the restart, you can again integrate your device into your Homematic IP system. Maintenance and cleaning The product does not require any maintenance.
General information about radio operation Enlist the help of an expert to carry out any maintenance or repairs. Clean the device using a soft, lint-free cloth that is clean and dry. Do not use any detergents containing solvents, as they could corrode the plastic housing and label. General information about radio operation Radio transmission is performed on a non-exclusive...
Technical specifications Technical specifications Device short description: HmIP-FAL230-C6 Construction of the regulation and control device: independently mounted electronic regulation and control device, surface mount Number of heating zones: Number of actuators: 9 / (8) Number of pumps: Supply voltage: 230 V/50 Hz Current consumption: 6.3 A max.
Technical specifications Ambient temperature: 0 - 50°C Type: 1.B. Withstand voltage: 2500 V Temperature glow wire test: 850 °C Temperature ball pressure test: 125 °C PTI value of housing: IIIb with 100 < CTI < Dimensions (W x H x D): 225 x 75 x 52 mm Weight: 566 g...
Page 81
Technical specifications domestic waste! Electronic equipment must be disposed of at local collection points for waste electronic equipment in compliance with the Waste Electrical and Electronic Equipment Directive. Information about conformity The CE sign is a free trading sign addressed ex- clusively to the authorities and does not include any warranty of any properties.
Page 82
Kostenloser Download der Homematic IP App! Free download of the Homematic IP app! Bevollmächtigter des Herstellers: Manufacturer’s authorised representative: eQ-3 AG Maiburger Straße 29 26789 Leer / GERMANY www.eQ-3.de...